4PORTS VDSL2 11N MODEM WITH GIGAWAN SR500N User Manual
ZXDSL 831AII User Manual CONTENTS 1. OVERVIEW .................................................................................................................................................................................... 5 1.1 ABOUT VDSL ................................................................................................................................................................. 5 1.2 DEVICE INTRODUCTION ...............................................................................
ZXDSL 831AII User Manual Caution This device complies with Part15 of the FCC Rules.
ZXDSL 831AII User Manual CO Central Office EC Echo Canceling -4-
ZXDSL 831AII User Manual OVERVIEW 1. OVERVIEW 1.1 ABOUT VDSL VDSL is a fast version of ADSL.VDSL MODEM is a broadband Internet access device，which utilizes the high frequency segment of the phone line to transmit high-speed data without interfering with the voice transmission. The frequency of VDSL signal is higher than that of voice, so voice and VDSL signal can coexist in one line by using a splitter to insulate each from the other. VDSL data transfer on the asymmetry way. The upload speed is up to 19.
ZXDSL 831AII User Manual ② Power switch: To turn on or turn off the power. ③ Reset Key: Reset default configuration. ④ Ethernet Interface: To be connected to a PC network card by a network cable, also can use a crossover cable to connect to Hub, Switch or Router. ⑤ Line Interface: Connected with phone line or “VDSL” port of the splitter. 1.3 LED STATUS INDICATION Table 1.
ZXDSL 831AII User Manual HARDWARE INSTALLATION AND SOFTWARE CONFIGURATION 2. HARDWARE INSTALLATION AND SOFTWARE CONFIGURATION 2.1 SYSTEM REQUIREMENT A computer with a USB interface or a network card with Ethernet interface. 2.2 HARDWARE INSTALLATION 2.2.1 HARDWARE CONNECTION Figure 2.1 To go online and make phone calls simultaneously, please refer to Appendix B: SPLITTER CONNECTION. 2.2.2 INSTALLATION STEPS 1.
ZXDSL 831AII User Manual 2. 3. 4. modem. Connect Ethernet port of the VDSL MODEM to Ethernet port of the computer using the network cable that comes with the modem. Connect USB port of the VDSL MODEM to USB port of the computer using the USB cable that comes with the modem. Plug in the power cord , and turn on the power. 2.3 SOFTWARE CONFIGURATION 2.3.1 PREPARATION BEFORE SOFTWARE INSTALLATION Before the installation, please confirm information below or consult with the VDSL service provider. Table 2.
ZXDSL 831AII User Manual Figure 2.2 2.3.4 VDSL MODEM WORK MODE CONFIGURATION 1． For different protocols, the users need to set VDSL Modem accordingly as listed below: Table 2.2 PPPoE PPPoA 1483 Bridged ATM VC Protocol Use DNS User Name Password √ PPPoE Enable √ √ √ PPPoA Enable √ √ Lower interface Default route √ Disable Note: √ means configure according to VDSL service provider’s instructed value. PPPoE can also be realized via third party dialup software.
ZXDSL 831AII User Manual Figure 2.3 PROTOCAL CONFIGURATION 3. PROTOCOL CONFIGURATION If the configuration is bridge encapsulation, there is no need to configure any more parameters. Only need to use the third party dial-up software to connect the Internet. Totally, this router supports：PPPoA、PPPoE、Bridging. For detail configuration information, please check the following configuration guide. 3.
ZXDSL 831AII User Manual Figure 3.1 Click on the next connection which you want add. Press “Add” button, enter the configure guide, as Figure 3.2 Figure 3.2 The value for VPI/VCI is assigned by your ISP. After inputing the PVC value, press “Apply/Save” to save configuration. As Figure 3.3.
ZXDSL 831AII User Manual Figure 3.3 The Modem supports five VDSL protocol modes. Choose the protocol which is appointed by ISP and PVC encapsulation. • PPP over ATM (PPPoA) • PPP over Ethernet (PPPoE) • Bridging Some connection lines need to confirm the LLC or VC, if you can’t confirm, please don’t modify the default value or ask your ISP. 3.2 RFC1483 BRIDGE CONFIGURATION Click “Advanced Setup” on the left page, enter into “WAN Service Setup” page. As Figure 3.4.
ZXDSL 831AII User Manual Figure 3.4 Press “Next” button, enter the configure guide, as Figure 3.5 Figure 3.5 Press “Next” button, enter the configure guide, as Figure 3.
ZXDSL 831AII User Manual Figure 3.6 Press “Apple/Save” to save your configuration,and you will see as following Figure 3.7. . Figure 3.7 3.3 PPPOA AND PPPOE CONFIGURATION PPPoE is also known as RFC 2516. It is a method of encapsulating PPP packets over Ethernet. PPPoA is also known as RFC2364 and named as Peer to Peer Protocol over ATM. As PPPoE, it also has all the features of PPP. Although it’s based on ATM protocol, the setting of all the other parameters is similar with PPPoE.
ZXDSL 831AII User Manual an existing connection Figure 3.8 Press “Next” button, enter the configure guide, as Figure 3.9 Figure 3.9 The value for VPI/VCI is assigned by your ISP.Press “Next” button, enter the configure guide, as Figure 3.10.
ZXDSL 831AII User Manual Figure 3.10 Ealble “Fullcone NAT “press “Next” to continue. As Figure 3.11. Figure 3.11 Press “Next” to continue. As Figure 3.
ZXDSL 831AII User Manual . Figure 3.12 Configure your DNS info and press “Next” to save your configuration,and you will see as following Figure 3.13. .
ZXDSL 831AII User Manual Figure 3.13 Press “Apply/Save” to save your configuration. As Figure 3.14. Figure 3.
ZXDSL 831AII User Manual 4.1 TCP/IP PROTOCOL CONFIGURATION 1. Set IP address as “192.168.1.1”; 2. Set netmask as”255.255.255.0”; 4.2 MODEM CONFIGURATION 1. Click “Advanced Setup” on the left page, enter into “Url Filter” page, shown as Figure 4.1. Figure 4.1 2.
ZXDSL 831AII User Manual a) b) Choose Exclude or Include,then press “add” to add the url you want to configration. Fill in the url and press Apply/Save to save your configration, shown as Figure 4.2 Figure 4.
ZXDSL 831AII User Manual OTHER FUNCTIONS AND CONFIGURATION 5. OTHER FUNCTIONS AND CONFIGURATION 5.1 STATUS CHECKING The working status of VDSL MODEM can be monitored by some pages. 1． Overview of Device Information As shown in Figure 5.1, the information of hardware version, software version, DSL link status, link speed and LAN interface can be viewed on this page.
ZXDSL 831AII User Manual Figure 5.1 5.2 CONFIGURATION OF MODEM’S IP ADDRESS AND PASSWORD 1. CONFIGURATION OF MODEM’S IP ADDRESS As a network device, VDSL Modem has its own IP address and MAC address. The factory sets the VDSL Modem at a default IP address of 192.168.1.1 and subnet mask of 255.255.255.0. The user can configure these addresses through the Local Network page as shown in Figure 5.2 Figure 5.2. 2.
ZXDSL 831AII User Manual RESET TO DEFAULT SETTING 6. RESET TO DEFAULT SETTING If you are experiencing difficulty logging on to the configuration page (For example: you forget the password), you can reset the VDSL MODEM to the default configuration，Then you will be able to log on with the default username and password. Method: Turn on the VDSL MODEM, put a pin into the eyelet, and press only once.
ZXDSL 831AII User Manual USAGE OF USB INTERFACE 7. USAGE OF USB INTERFACE The Combo DSL Gateway is a device with both Ethernet Interface and USB Interface, which is independent, you may use either of them to connect to the different computers, in this way the two computers can connect to the network at one time. The Gateway can be seen as a simple two-port HUB. So, do not connect both the Ethernet Interface and USB Interface to a same computer. When using USB Interface, you must install the drivers.
ZXDSL 831AII User Manual Figure 7.1.1 2. A new dialog box will show you a figure 7.1.2. Click “Accept” to continue. Figure 7.1.2 3. A new box will show whether you want to reboot the computer. then click “close” button to finish the installing.
ZXDSL 831AII User Manual Figure 7.1.3 7.2 UNINSTILL DRIVER 1.Click “Start” à “Programs” à “DSL Two Ports MODEM” à “Uninstall”. As shown figure 7.2.1. Figure 7.2.
ZXDSL 831AII User Manual 2. It will ask you to click“Yes”to confirm deletion. As shown figure 7.2.2. Figure 7.2.2 3．Choose “Yes, reboot the computer now”. As shown figure 7.2.3. Figure 7.2.3 7.3 CONFIGURATION OF "USB IAD LAN MODEM" As a virtual network card, "USB IAD LAN MODEM " can be configured as a normal network card. Set the computer IP address at same segment of VDSL MODEM, such as set the IP address of the network card to one of the “192.168.1.3”～ “192.168.1.254”.
ZXDSL 831AII User Manual Figure 7.3.
ZXDSL 831AII User Manual SPECIFICATION 8. SPECIFICATION 8.1 POWER SUPPLY l Exterior power adapter l Input: 220VAC, 50Hz l Output: 12VDC. l Polarity： 8.2 STANDARDS l EMI/Immunity: FCC Part 15 Class B, CE Mark (EN55022 Class B/EN50082) l Safety Standard: UL, EN60950, 3C l Communication: FCC Part 68, CYR21 l Electromagnetic: in accordance with FCC, ETSI and CISPR standard 8.
ZXDSL 831AII User Manual APPENDIX APPENDIX APPENDIX A. TROUBLESHOOTING Phenomena Solution 1. The indicator of power 2. supply is not on 3. The indicator of PC is not on Make sure the connection of power supply is good. Make sure the switch of power supply is turned on. Make sure the output of power supply is correct. 1. Check the connection between the cable and the network card. 2. Make sure that the correct cable is used. 3. Make sure the cable works fine by pinging the host IP address. 1.
ZXDSL 831AII User Manual APPENDIX B. SPLITTER CONNECTION 1. Splitter 2. Connection Firstly, use a telephone cord to connect the LINE port of the splitter and the RJ-11 port (the phone jack) on the wall. Then use another telephone cord to connect the VDSL port of the splitter and the LINE port of the VDSL Modem. Finally, use another telephone cord to connect the telephone set and the PHONE port of the splitter.
ZXDSL 831AII User Manual APPENDIX C. CONFIGURATION OF TCP/IP PROTOCOL Here we will explain the configuration which using Windows 2000 operation system as an example. For other operation systems the process is similar. 1. Right click on the “Local Area Connection”, click “Properties” on the pop up menu, as shown in Figure C.1. 2. Figure C.1 The dialog box of networks is shown in Figure C.2. On the “General” property page select “Internet Protocol(TCP/IP)”，and then click the “Properties” button. Figure C.
ZXDSL 831AII User Manual 3. The “Internet Protocol (TCP/IP) properties” pop up window is shown as Figure C.3. Select “Use the following IP address”. Input the following IP address: 192.168.1.11 and subnet mask: 255.255.255.0 (These addresses and subnet mask are similar with the factory default setting. The user can set different IP address and subnet mask whenever necessary). Select “Gateway”, input the default IP address of the gateway: 192.168.1.1 and IP address of Preferred DNS server: 202.96.209.
ZXDSL 831AII User Manual APPENDIX D. SHIPPING LIST Make sure the following items are included in the box. If any one of them is missing, please contact the vendor immediately.
ZXDSL 831AII User Manual FCC INFORMATION This equipment complies with CFR 47, Part 15.19 of the FCC rules. Operation of the equipment is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.
