SMART/RG SR400ac 802.11ac Gigabit Router User Manual V1.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Contents 1 Safety Precautions ............................................................................................. 1 2 Overview ............................................................................................................ 2 3 2.1 Product Introduction .............................................................................. 2 2.2 Packing list .............................................................................
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 7 6.9 Storage ................................................................................................ 33 6.10 Radio ................................................................................................... 34 6.11 SSID .................................................................................................... 36 6.12 Passpoint .............................................................................................
SMART/RG SR400ac 802.11ac Gigabit Router User Manual About User Manual This user manual mainly describes how to install and configure the wireless router. Organization This user manual is organized as follows: Chapter Descriptio n Provides safety Chapter 2 Safety Precautions precaution information . Provides a general overview of Chapter 3 : Overview the wireless router, and the packing list.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual procedure for hardware installation . Describes how to set the TCP/IP and how to Chapter 5 : TCP/IP Settings and Wireless Connection Introduction connect the wireless router wirelessly. Describes how to log Chapter 6 : Logging In to the Web Page in to the wireless router. Mainly describes how to navigate through the Chapter 7 : Web Configuration Web pages and how to configure the parameter s.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual BSS-MAC oting Select desired BSS to configure (SSID) Show Mode whether the BSSID information is AP, WirelessBridge, WET or STA. BSS Enabled Enable or disable this SSID. Network Set the Network Name (also known as Name (SSID) SSID) of this network. Select Closed hides the network from Network Type active areas. Select Open reveals the network to active scans. Select On enables AP isolation mode.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual capabilities required for stations to associate to the mode required BSS supported by the interface: none – no requirements on joining devices. erp – devices must advertise ERP (11g) capabilities to be allowed on a 2G band BSS. ht – devices must advertise HT (11n) capabilities to be allowed on the BSS. vht – devices must advertise VHT (11ac) capabilities to be allowed on the BSS. 1.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Wireless Interface Select which wireless interface to configure. ANQP Elements: 802.11u ANQP Parameters 802.11status Enable or disable 802.11u Interworking Capability for this SSID. Internet Enable or disable Internet Access capability Access for this SSID. Network Access Type Interworking HESSID IP Network Access Type. Set Interworking HESSID of this network.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field Description Wireless Select Interface configure. 802.11 Select 802.11 authentication method. Authentication Open or shared. 802.11X Authentication WPA WPA-PSK WPA2 WPA2-PSK BRCM-PSK WPA2 Preauthentication which wireless interface to Select Network anthentication type. Enable/Disable WPA Authenticated Key Management suite. Enable/Disable WPA-PSK Authenticated Key Management suite.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual WEP Encryption WPA Encryption Enable/Disable WEP data encryption. Select the WPA data encryption algorithm. Set the IP address of the RADIUS server RADIUS Server to use for authentication and dynamic key derivation. Set the UDP port number of the RADIUS RADIUS Port server. The port number is usually 1812 or 1645 and depends upon the server. RADIUS Key 1.3 Set the shared secret for the RADIUS connection.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Wireless Interface WPS Current Mode WPS Configuration Select which wireless interface to configure. WPS Current Mode Select WiFi Simple Config mode. Wifi-Invite Enable or disable Wifi-Invite feature. Wifi-Invite Set the Wifi-Invite PIN Mode to auto or PIN Mode manual. List Wifi-Invite enabled STAs Wifi-Invite enabled STAs Scan to find Wifi-Invite enabled STAs.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field Boot Loader Version Description Display the current version of Boot Loader. OS Vertion Display the current version of OS. WL Display the current version of Wireless Driver Version Driver. Device Mode Display the current devicemode. New Fireware Select the new firmware to upload to the router. Download Push button to save NVRAM variables to NVRAM file file.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Features Support IEEE802.11b, IEEE802.11g, IEEE802.11n, IEEE802.11a, IEEE802.11ac.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 2 Safety Precautions Before operating the wireless router, read the following precaution information carefully: Use the type of power that user manual marks. Use the power adapter that is packed within the device package. Pay attention to the power load of the outlet or the prolonged lines. An overburden power outlet or damaged lines and plugs may cause electric shock or fire accident. Check the power cords regularly.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 3 Overview 3.1 Product Introduction The wireless router is a high-performance network access device. It is fully compatible with IEEE802.11b, IEEE802.11g, IEEE802.11n and IEEE802.11ac standards. It can provide reliable and convenient access service for individual users and SOHO (Small Office, Home Office). 3.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 4 Hardware Description and Hardware Installation 4.1 Front Panel and LED Status There are 12 LED indicators on the front panel of the wireless router. By observing their status, you can check whether the device runs normally.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes the status of LED indicators on the front panel. Indicator Color Status Description The device is powered on and the device is On operating normally. White power Blink The device is initializing. Off The device is powered off. On The device is in CFE recovery mode. Amber The software is upgrading or the RESET button Blink was pressed. Ethernet WAN interface is connected at 1000 On BASE-T.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Internet is synchronized successfully in routed On mode. White Internet Blink Internet data is being transmitted. Off Ethernet WAN interface is disconnected. On Internet Authentication/Connection has failed. Off Normally off. Red The Ethernet interface is connected at 10/100 On BASE-T. Green Data is being transmitted through the Ethernet Blink interface. Off The Ethernet interface is disconnected.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual No USB device is connected or someone clicked Off the Safely Remove Hardware button, and it is now safe to remove the attached USB device. The connection of 3G/4G dongle or USB flash On disk is established @ USB 3 High-Speed (5Gbps). Data is being transmitted @ USB 3.0 High-Speed White Blink (5Gbps). No USB device is connected or someone clicked Off the Safely Remove Hardware button, and it is now safe to remove the attached USB device.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Off The 2.4GHz WiFi radio is off/disabled. On The 5GHz WiFi radio is operating. The router is sending/receiving WiFi traffic on White Blink 5GHz band. 5GHz White Off The 5GHz WiFi radio is off/disabled. On WPS pairing process was successful. Blink WPS pairing process is active. Off WPS pairing process is inactive. WPS The Ethernet interface is connected at 1000 On BASE-T.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes interfaces and buttons on the side panel. Interface/Button Description This button is used for enabling WPS PBC mode. When WPS WPS is enabled, press this button, and the AP starts to accept negotiation of PBC mode. Wifi 4.3 Turn on/off Wifi. USB3.0 USB 3.0 interface. On/Off Turn/off the router.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes interfaces and buttons on the side panel. Interface/Button Description LAN1/LAN2/ RJ45 LAN interfaces, for connecting hub, switch, or computer LAN3/LAN4 in a LAN. RJ45 WAN interface, for connecting WAN or the uplink WAN network devices. Use a fine needle to press Reset gently for 3-6 seconds and Reset then release the button. The system reboots and restores to USB 2.0 USB 2.0 interface.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 4.4.2 Before You Begin Before you install the device, please pay attention to the following items: When the device is connected to a computer, hub, router or switch, the Ethernet cable should be less than 100 meters. Do not place this device on an unstable surface or support. Do not put this device on the ground. Keep the device clean. Avoid the device from direct sunshine. Avoid any metal in the device.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual To realize roaming in the coverage range of the wireless router by a wireless client, you need to set the APs properly as follows: Set the same SSID for different APs. The SSIDs of all the computers and PDAs should be consistent with that of APs. All the BSSs must use the same wireless channel.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 5 TCP/IP Settings and Wireless Connection Introduction 5.1 TCP/IP Settings By default, the LAN IP address of the wireless router is 192.168.1.1, the subnet mask is 255.255.255.0, and the DHCP server is enabled. It is recommended to set the network adapter to Obtain an IP address automatically. Then, your PC obtains the TCP/IP settings, including the IP address, subnet mask, gateway, and DNS address automatically through the wireless router.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Step 2 Right-click the network adapter icon and choose Properties from the menu. The Local Area Connections Properties window appears. Note: If multiple network cards are installed on your PC, a window other than the Local Area Connections Properties window may appears. Step 3 Double-click Internet Protocol (TCP/IP) and the Internet Protocol (TCP/IP) Properties window appears.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Step 4 Select Use the following IP address and enter the IP address of the network adapter. The IP address must be 192.168. 1.X (X is a number in the range of 2 to 254). If you want to access the Internet through a wireless router, you need to enter the default gateway and IP address of the DNS server correctly.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Step 5 Set the subnet mask and click OK. Step 6 After setting, you can ping the default IP address of the wireless router, to check whether the current connection between the PC and the wireless router is normal. Choose Start > Run from the desktop and enter ping 192.168.1.1.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Note: 192.168.1.1 in the ping command is the default IP address of the LAN interface. If the IP address changes, enter the current IP address instead. Step 7 If the PC can ping through the default IP address of the wireless router, the following page appears, indicating that the connection between your PC and the wireless router is normal. 5.2 Wireless Connection Introduction By default, the AP function of the wireless router is enabled.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Step 1 Enable the wireless network adapter on your PC and ensure that the Wireless Zero Configuration tool is available. Right-click the Wireless Network Connection icon and choose View Available Wireless Networks from the menu. Step 2 In the Wireless Network Connection page, click Refresh network list and the network list is refreshed. The default SSID of the wireless router is Broadcom24 (2.4G) or Broadcom58 (5.8G).
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Note: After your wireless network card connects to the wireless router successfully, usually, you should set the network adapter to Obtain an IP address automatically. The configuration of wireless connection is now complete.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 6 Logging In to the Web Page Run the Internet Explorer (IE), enter http://192.168.1.1/ (the default IP address of the wireless router) in the address bar, and press Enter. In the pop-up window, enter the user name and password, and click Login. Note: The default user name is void and the default password is admin. After logging in to the Web page, you can view, configure and modify the router settings.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 7 Web Configuration 7.1 Basic You can set the basic operation of the router by following this wizard. To configure the basic operation, do as follows: Step 1 After login, click Basic in the navigation bar on the top pane of the page. The Basic page appears. The following table describes parameters in this page: Field Local Time Description Show the local time as kept in the router.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Field Description Router Set the username for access to these configuration pages. Username Router Set the password for access to these configuration pages, Leave Password this filed and Router Username blank to disable access control. Router Mode Choose Router or Access Point here. Firewall Sets whether the firewall shoule be disabled, Connetctions from the WAN are allowed if the firewall is disabled.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 7.2 LAN Click LAN to switch to LAN configuration page. In this page, you can configure the parameters of the LAN port. You can modify the IP address of the LAN port according to the actual network environment. This router supports Guest Network, so you can set LAN configuration on both Internel Network and Guest Network. 7.2.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 7.2.2 DHCP configuration The following table describes parameters in this picture: Field Description DHCP Server If it is set Enabled, the router serves as the DHCP server and automatically assigns IP addresses for all connected computers. DHPC Starting IP The first address in a consecutive IP address pool. Address DHCP Ending IP The last address in a consecutive IP address pool.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Field Description 6to4 is an Internet transition mechanism for migrating from IPv4 to IPv6, a system that allows IPv6 packets to be transmitted over an IPv4 network (generally the IPv4 Internet) without the need to configure explicittunnels. IPv6 LAN Network Set IPv6 LAN Network Prefix here. Prefix IPv6 DNS Server If you want to surf the Internet through IPv6, IPv6 DNS IPv6 6to4 subnet ID Set the 6to4 subnet ID(0-65535).
SMART/RG SR400ac 802.11ac Gigabit Router User Manual DHCP If you select DHCP, the router automatically obtains IP address, subnet mask, and IP address of the gateway from the ISP. Select this connection mode if the ISP does not provide any IP network parameters. Static IP (Fixed) If the ISP provides the information of the IP address, subnet mask, gateway, and DNS server, select Static. For detailed settings, refer to your ISP.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in the above picture: Field Host Name Description Some ISPs require that a host name be provided when requesting an IP address through DHCP. Domain Name Set the domain name to be provided to LAN clients who request an IP address through DHCP MAC Address Some ISPs require that a specific MAC address be used. Also known as MAC address cloning, this feature allows you to set the MAC address of the WAN interface.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field Description PPPoE Username PPPoE Password PPPoE Server Name PPPoE Access Concentrator PPPoE Connect on Demand PPPoE Set the username to use when authenricating with a PPPoE server. Set the password to use when authenticating with a PPPoE server Set the PPPoE server name. Set the name of the PPPoE access concentrator.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 7.5 FILTERS Click FILTERS in the navigation bar on the top pane of the page, the FILTERS page appears. This page allows you to configure LAN filters for the router. The LAN machines affected by the filters will not be able to communicate through the WAN but will be able to communicate with each other and with the router itself.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field LAN MAC Description Fiter Mode Select whether clients with the specified MAC address are allowed of denied access to the router and the WAN Filter packets from LAN machines with the specified MAC LAN MAC Fiters address.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field Description Forward packets destined to ports in the first range to the Port Forwards LAN machine with the specified IP address. You may optionally specify a second range (the range may not overlap and must be the same size). NAT Type DMZ IP Address Symmetric NAT is more secured, Cone NAT traversal technology like Teredo.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field Description Enable Qos Enable the Qos feature. Prioritizes ACK Prioritize the transmit ACK packets. Prioritize ICMP Prioritize the ICMP packets (PING replies, etc). Default Traffic Class IQos default traffic class for unclassified traffic. Inbound Classes (% Max Input BW) BW Max inbound Set the maximum bw for inbound traffic.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 7.8 Media Click Media in the navigation bar on the top pane of the page, the Media page appears. This page allows you to configure the basic Media related parameters. The following table describes parameters in this page: Field Description Enable IGMP Proxy Enable IGMP Proxy in AP mode: 0: disable; 1: enable. BandSteering Role of BandSteering Daemon: 0: disable; 1: primary; Daemon 2:helper; 3: standalone.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Field Stalled Description Link Detection Stalled Link Detection Threshold, 0 to disable. Threshold Packet Saving Retry Limit Unicast IGMP Query Multicast Data Sendup Send Set PsPretend retry limit, 0 to disable. Convert multicast IGMP mac packet to unicast mac packet. Send (sendup) multicast packets from EMF/WMF to host always. multicast packets to PSTA Send multicast packets to PSTA.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field Description DLNA Server Set whether DLNA Server is enabled. Content Directory Tell DLNA Server which directory is going to scan. DLNA Renderer Set whether DLNA Renderer is enabled. Samba Mode Set Samba Mode. User Name Samba User Name. Password Set samba password for remote connection. 7.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Click Radio in the navigation bar on the top pane of the page, the Radio page appears. This page allows you to configure the Physical Wireless interfaces. The following table describes parameters in this page: Field Description Wireless Interface Select which wireless interface to configure. Country Restrinct the channel set based on country requirements. Interface Enable or disable the wireless interface. 802.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Field Basic Rate Set Multicast Rate Description Select the basic rates that wireless clients must support. Force the multicast/broadcast transmission rate for the AP to a particular speed. Regulatory Mode Select a regulatory mode to use. TPC Mitigation (db) Power Mitigation factor (in db). OBSS Coexistence Enable/disable Overlapping BSS Coexisistence aka 20/40 Coex. 7.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Wireless Interface BSS-MAC (SSID) Select which wireless interface to configure. Select desired BSS to configure Show whether the BSSID is AP, WirelessBridge, WET or Mode STA. BSS Enabled Enable or disable this SSID. Network Name (SSID) Set the Network Name (also known as SSID) of this network. Select Closed hides the network from active areas.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual advertise VHT (11ac) capabilities to be allowed on the BSS. 7.12 Passpoint Click SSID in the navigation bar on the top pane of the page, the SSID page appears. This page allows you to configure the Passpoint parameters for each Virtual/Physical interface. The following table describes parameters in this page: Field Description Wireless Interface Select which wireless interface to configure. ANQP Elements: 802.11u ANQP Parameters 802.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual Field Description Interworking Set Interworking HESSID of this network. HESSID IP Address Type Availability Information IPv4 IPv6 Network Authentication Type List Realm List Set IP Address Type Availability Information to this BSS supported by this interface. Set IPv4 Address Type Avaliability to this BSS supported by this interface. Set IPv6 Address Type Avaliability to this BSS supported by this interface.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field Wireless Interface 802.11 Authentication 802.11X Authentication WPA WPA-PSK WPA2 WPA2-PSK BRCM-PSK WPA2 Preauthentication Description Select which wireless interface to configure. Select 802.11 authentication method. Open or shared. Select Network anthentication type. Enable/Disable WPA Authenticated Key Management suite. Enable/Disable WPA-PSK Authenticated Key Management suite.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual The following table describes parameters in this page: Field Description Wireless Interface Select which wireless interface to configure. WPS Current Mode WPS Current Mode WPS Configuration Select WiFi Simple Config mode. Wifi-Invite Enable or disable Wifi-Invite feature. Wifi-Invite PIN Mode List Wifi-Invite enabled STAs Wifi-Invite enabled STAs Set the Wifi-Invite PIN Mode to auto or manual. Scan to find Wifi-Invite enabled STAs.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 7.15 FIRMWARE Click FIRMWARE in the navigation bar on the top pane of the page, the FIRMWARE page appears. This page allows you to upgrade the firmware. The following table describes parameters in this page: Field Boot Description Loader Version Display the current version of Boot Loader. OS Vertion Display the current version of OS. WL Driver Version Display the current version of Wireless Driver. Device Mode Display the current devicemode.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual 8 Troubleshooting Failure to configure the router through a web browser (1) Open the Web browser (for example, IE) and choose Tools > Internet Options from the main menu. (2) Click Delete Cookies and Delete Files. Failure to establish wireless network connection Because the router is beyond the wireless coverage.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual (1) Place the router near the customer premises equipment (CPE). (2) Try modifying the channel setting. Because of authentication problems. (1) Use a computer of wired connection to connect the router. (2) Check the network security settings. (3) Try hard reset on the router. Because the router cannot be detected. (1) Try hard reset on the router and test again. (2) Check the settings of the wireless network.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual (9) Check the LAN settings of your Internet options, and do not use a proxy server for your LAN.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
SMART/RG SR400ac 802.11ac Gigabit Router User Manual —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits .
SMART/RG SR400ac 802.11ac Gigabit Router User Manual radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The device is compliance with RF exposure limits, users can obtain Canadian information on RF exposure and compliance.
