4 Port ADSL2+ 11n 150Mbps Router SR310N USER MANUAL
ADSL MODEM USER MANUAL CONTENTS 1. OVERVIEW ................................................................................................................................. 4 1.1 ABOUT ADSL AND ADSL 2+ ............................................................................ 4 1.2 DEVICE INTRODUCTION ................................................................................ 4 1.3 LED STATUS INDICATION............................................................................... 5 1.4 PROTOCOLS .
ADSL MODEM USER MANUAL Related Documents Definition & Acronyms ATU-C ADSL Transceiver Unit, Central Office End ATU-R ADSL Transceiver Unit, Remote Terminal End FEXT Far-end Cross Talk HDSL High-rate Digital Subscriber Line POTS Plain Old Telephone Service PSTN Public Switched Telephone Network WINS Windows® Internet Name Server ADSL Asymmetric Digital Subscriber Line OAM Operations, Administration And Maintenance QAM Quadrature Amplitude Modulation DMT Discrete Multitone DSL Digital
ADSL MODEM USER MANUAL OVERVIEW 1 1. OVERVIEW 1.1 ABOUT ADSL AND ADSL 2+ ADSL MODEM is a broadband Internet access device，which utilizes the high frequency segment of the phone line to transmit high-speed data without interfering with the voice transmission. The frequency of ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. ADSL data transfer on the asymmetry way.
ADSL MODEM USER MANUAL Interface introduction: a) Power Interface: 12V DC, 500mA. b) c) d) Switch: To turn on or turn off the power. WIFI: To switch on or switch off the WIFI. LAN1~LAN4: Connect Ethernet port of the Gateway with 10/100BASE-T port of the computer using the network cable that comes with the modem Line: Connected with phone line or “ADSL” port of the splitter. e) . 1.3 LED STATUS INDICATION Table 1.
ADSL MODEM USER MANUAL 6. Support GUI Upgrading. 7. ATM management function. 8. Wireless access distance is more than 150m 1.6 ABOUT WIRLESS ADSL An ADSL MODEM is a broadband Internet access device, which utilizes the high frequency segment of the phone line to transmit high-speed data without affecting the voice transmission. The frequency of the ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other.
ADSL MODEM USER MANUAL HARDWARE INSTALLATION AND SOFTWARE CONFIGURATION 2 2. HARDWARE INSTALLATION AND SOFTWARE CONFIGURATION 2.1 SYSTEM REQUIREMENT A computer with a network card with Ethernet interface. 2.2 HARDWARE INSTALLATION 2.2.1 HARDWARE CONNECTION Figure 2.1 To go online and make phone calls simultaneously, please refer to Appendix B: SPLITTER CONNECTION. 2.2.2 INSTALLATION STEPS 1.
ADSL MODEM USER MANUAL 2. 3. modem. Connect Ethernet port of the ADSL MODEM to Ethernet port of the computer using the network cable that comes with the modem. Plug in the power cord , and turn on the power. 2.3 SOFTWARE CONFIGURATION 2.3.1 PREPARATION BEFORE SOFTWARE INSTALLATION Before the installation, please confirm information below or consult with the ADSL service provider. Table 2.1 shows all the information needed to configure for different protocols. Table 2.
ADSL MODEM USER MANUAL Figure 2.2 2.3.4 ADSL MODEM WORK MODE CONFIGURATION 1． For different protocols, the users need to set ADSL Modem accordingly as listed below: Table 2.2 PPPoE PPPoA 1483 Bridged PVC Protocol Use DNS User Name Password √ PPPoE Enable √ √ √ PPPoA Enable √ √ PVC Default route √ Disable Note: √ means configure according to ADSL service provider’s instructed value. PPPoE can also be realized via third party dialup software.
ADSL MODEM USER MANUAL PROTOCAL CONFIGURATION 3 3. PROTOCOL CONFIGURATION If the configuration is bridge encapsulation, there is no need to configure any more parameters. Only need to use the third party dial-up software to connect the Internet. Totally, this router supports：PPPoA、PPPoE、Bridging. For detail configuration information, please check the following configuration guide. 3.1 CONFIGURATION GUIDE Click “Internet” on “Interface Setup” Tab. You can modify the configuration.
ADSL MODEM USER MANUAL Figure 3.2 Figure 3.3 The Modem supports three ADSL protocol modes. Choose the protocol which is appointed by ISP and PVC encapsulation. Below, we introduce the configuraion of the three protocol modes.
ADSL MODEM USER MANUAL • PPP over ATM (PPPoA) • PPP over Ethernet (PPPoE) • Bridging Some connection lines need to confirm the LLC or VC, if you can’t confirm, please don’t modify the default value or ask your ISP. 3.2 RFC1483 BRIDGE CONFIGURATION If you get the correct PVC (VPI/VCI) which you can get from the ISP, you don’t need modify another parameter. Click “save” to save configuration as Figure 3.4. Figure 3.4 3.3 PPPOA AND PPPOE CONFIGURATION PPPoE is also known as RFC 2516.
ADSL MODEM USER MANUAL PPPoE. So we only introduce PPPoE in detail here. In Figure 3.4, select PPP over Ethernet (PPPoE), entering the configuration interface, as Figure 3.5 Figure 3.
ADSL MODEM USER MANUAL In Figure 3.4, select PPPoA from “Encapsulation”entering the configuration interface, as Figure 3.6 Figure 3.
ADSL MODEM USER MANUAL Select “Get IP Address Dynamic”and enter Severvice name、username、password. Broadband User Name: Your account from ISP to access Internet. Password: Input the password assigned by your ISP.
ADSL MODEM USER MANUAL APPLICATION OF DHCP 4 4. APPLICATION OF DHCP Apart from being a modem, ADSL Modem can also support router and DHCP applications, which are especially applicable for small business, small scale LAN, net-café, etc. The ADSL Modem can work as a router and DHCP sever without proxy server. The configuration steps are shown below: 4.1 TCP/IP PROTOCOL CONFIGURATION 1. Set IP address as “Automatically obtain IP address”; 2. Set gateway’s IP the same as Modem’s; 4.2 MODEM CONFIGURATION 1.
ADSL MODEM USER MANUAL Figure 4.
ADSL MODEM USER MANUAL OTHER FUNCTIONS AND CONFIGURATION 5 5. OTHER FUNCTIONS AND CONFIGURATION 5.1 STATUS CHECKING The working status of ADSL MODEM can be monitored by some pages. 1． Overview of Device Information As shown in Figure 5.1, the information of Firmware Version, ADSL firmware Version, ADSL link status, link speed and LAN interface can be viewed on this page.
ADSL MODEM USER MANUAL Figure 5.1 5.2 CONFIGURATION OF MODEM’S IP ADDRESS AND PASSWORD 1. CONFIGURATION OF MODEM’S IP ADDRESS As a network device, ADSL Modem has its own IP address and MAC address. The factory sets the ADSL Modem at a default IP address of 192.168.1.1 and subnet mask of 255.255.255.0.
ADSL MODEM USER MANUAL addresses through the LAN page. 2. Configuration of administrator’s password and user’s password When logging on the setting page of ADSL Modem, the system requires user name and password to verify for permission. The default administrator’s account is “admin” and the default password for this account is “1234”. The user, through the user configuration tab on Administration page, can change the passwords.
ADSL MODEM USER MANUAL Figure 5.
ADSL MODEM USER MANUAL 5.3.1.2. Multiple SSID’S Settings SSID Index, SSID: The SSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change the default name to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure your wireless clients have exactly the SSID as the device, in order to get connected to your network.
ADSL MODEM USER MANUAL Pre-Shared key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters. The WPS Hardware Push Button and LED behaviors are defined as below: 1）Physical push button is pressed down and holds until the LED starts flashing, WPS starts to process and the LED will flash. 2）Push button (in the web UI) is pressed, WPS starts to process and the LED will flash.
ADSL MODEM USER MANUAL RESET TO DEFAULT SETTING 6 6. RESET TO DEFAULT SETTING If you are experiencing difficulty logging on to the configuration page (For example: you forget the password), you can reset the ADSL MODEM to the default configuration，Then you will be able to log on with the default username and password. Method: 1) Turn on the ADSL MODEM. 2) Keep pressing the RESET BUTTON for 6 seconds. 3) Release the RESET BUTTON when the PC light off. 4) Done.
ADSL MODEM USER MANUAL 7 SPECIFICATION 7. SPECIFICATION 7.1 POWER SUPPLY Exterior power adapter Input: 110VAC, 60Hz Output: 12VDC，500mA. Polarity： 7.2 STANDARDS EMI/Immunity: FCC Part 15 Class B, CE Mark (EN55022 Class B/EN50082) Safety Standard: UL, EN60950, 3C Communication: FCC Part 68, CYR21 Electromagnetic: in accordance with FCC, ETSI and CISPR standard 7.
ADSL MODEM USER MANUAL APPENDIX APPENDIX APPENDIX A. TROUBLESHOOTING Phenomena Solution 1. Make sure the connection of power supply is good. The indicator of power 2. Make sure the switch of power supply is turned on. supply is not on 3. Make sure the output of power supply is correct. 1. The indicator of LAN is not on Check the connection between the cable and the network card. 2. Make sure that the correct cable is used. 3. Make sure the cable works fine by pinging the host IP address. 1.
ADSL MODEM USER MANUAL APPENDIX B. SPLITTER CONNECTION 1. Splitter 2. Connection Firstly, use a telephone cord to connect the LINE port of the splitter and the RJ-11 port (the phone jack) on the wall. Then use another telephone cord to connect the ADSL port of the splitter and the LINE port of the ADSL Modem. Finally, use another telephone cord to connect the telephone set and the PHONE port of the splitter. APPENDIX C.
ADSL MODEM USER MANUAL 2. Figure C.1 The dialog box of networks is shown in Figure C.2. On the “General” property page select “Internet Protocol(TCP/IP)”，and then click the “Properties” button. Figure C.2 3. The “Internet Protocol (TCP/IP) properties” pop up window is shown as Figure C.3. Select “Use the following IP address”. Input the following IP address: 192.168.1.11 and subnet mask: 255.255.255.0 (These addresses and subnet mask are similar with the factory default setting.
ADSL MODEM USER MANUAL shown in Figure C.3. Figure C.3 4. Click “OK” button to return to the “Local Area Connection Property” dialog box. 5. Click “OK” button to close the Network property dialog box. APPENDIX D. SHIPPING LIST Make sure the following items are included in the box. If any one of them is missing, please contact the vendor immediately.
ADSL MODEM USER MANUAL FCC INFORMATION FCC Caution • Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
