４ PORTS ＋ 802.11n WIRELESS ADSL MODEM User Manual V 1.
DSL Gateway/Router — User Manual CONTENTS 1.OVERVIEW ....................................................................................................................................................... 3 1.1 ABOUT ADSL ...................................................................................................................................... 3 1.2 ABOUT ADSL2/2+............................................................................................................................... 3 1.
DSL Gateway/Router — User Manual 1.OVERVIEW 1.1 ABOUT ADSL An ADSL MODEM is a broadband Internet access device, which utilizes the high frequency segment of the phone line to transmit high-speed data without affecting the voice transmission. The frequency of the ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. ADSL data transfer adapts the asymmetry model.
DSL Gateway/Router — User Manual 2 SPECIFICATION 2.1 INTERFACE INTRODUCTION 2.1.1 INDICATOR AND INTERFACE Table 2.1 ITEM Indicator Interface Name State introduction POWER A steady Green light means the power connection works properly DSL Green, shows DSL line status.
DSL Gateway/Router — User Manual LINE Connected with telephone line ADSL Connect with the LINE port of the ADSL Modem using telephone line provided. PHONE Connect with telephone 2.2 HARDWARE CONNECTION Introduction： 1、 Use a telephone cord to connect the LINE port of the splitter with the RJ-11 port (the phone jack) on the wall. 2、 Use another telephone cord to connect the ADSL port of the splitter with the LINE port of the ADSL Modem.
DSL Gateway/Router — User Manual 3. CONFIGURATION 3.1 DEFAULT CONFIGURATION ADSL MODEM has pre-configured with the VCI/VPI which is in common use. 3.2 COMPUTER CONFIGURATION The default IP address for ADSL MODEM is: 192.168.1.1; The Subnet Mask is：255.255.255.0. Users can configure ADSL MODEM through an Internet browser.
DSL Gateway/Router — User Manual When you save the settings, the web page will be refreshed slowly, please wait it finished. Some settings only take effect after rebooting the router. 3.4 WAN CONFIGURATION If the configuration is bridge encapsulation, there is no need to configure any more parameters. Only need to use the third party dial-up software to connect the Internet. Totally, this router supports：PPPoA、PPPoE、MER、IPoA、Bridging.
DSL Gateway/Router — User Manual Figure 3.3 After your save, there will be one Layer2 Interface(atm3) added as following: Figure 3.4 Next, add one Layer3 Interface via “Wan Service” configuration page, and click “Add” button as following: Figure 3.5 You need to select one Layer2 Interface from the Layer2Interface List.
DSL Gateway/Router — User Manual Figure 3.6 Press “Next” to enter into “WAN Setup - Summary”, click “Apply/Save” to save configuration, if you need to modify the parameter, click “Back” as Figure 3.7. Figure 3.7 3.4.3 PPPOE ON ATM CONFIGURATION PPPoE is also known as RFC 2516. It is a method of encapsulating PPP packets over Ethernet. PPPoA is also known as RFC2364 and named as Peer to Peer Protocol over ATM. As PPPoE, it also has all the features of PPP.
DSL Gateway/Router — User Manual Press “Next” entering the configuring interface, as Figure3.9. Figure 3.9 PPP Username: Your account from ISP to access Internet. PPP Password: Input the password assigned by your ISP. PPPoE Service Name: Server name of network ISP. No need to set. Authentication Method: Authentication mode of network ISP. Default is AUTO. Dial on demand: When this mode is selected, the connection that has no traffic within assigned disconnect timeout (e.g.
DSL Gateway/Router — User Manual Figure 3.10 Press “Next” to setup default DNS server as following: Figure 3.11 Press “Next” to enter into “WAN Setup - Summary”, click “Apply/Save” to save configuration, if you need to modify the parameter, click “Back” as Figure 3.
DSL Gateway/Router — User Manual Figure 3.12 3.4.4 IPOE ON ATM CONFIGURATION In Figure3.6, select MAC Encapsulation Routing (MER), Figure 3.13 Press “Next”, and the IP address can be queried from your ISP, the result as Figure3.14.
DSL Gateway/Router — User Manual Figure 3.14 Press “Next” to configure services of Translation on this connection, as Figure 3.15: Figure 3.15 Press “Next” to select default gateway from Routing Interfaces as Figure 3.16: Figure 3.16 Press “Next” to setup default DNS server as Figure 3.
DSL Gateway/Router — User Manual Figure 3.17 Press “Next” to enter into “WAN Setup - Summary”, click “Apply/Save” to save configuration, if you need to modify the parameter, click “Back” as as Figure 3.18 Figure 3.18 3.5 WIRELESS CONFIGURATION Press “Wireless” on the top of web pages to enter wireless section. You can select to configure wireless setup, security and management.
DSL Gateway/Router — User Manual Figure 3.19 3.5.1 WIRELESS BASIC SETUP Click “Basic” on the left menu to setup basic wireless parameters. In default, check “Enable Ｗireless” box to launch wireless AP. SSID (Service Set Identifier): The mobile users cannot access WLAN until setting their SSID as the same value of the wireless ADSL. The SSID value of the ADSL is “default” Hide Access Point: If checked, wireless station will no see SSID of the ADSL. 3.5.
DSL Gateway/Router — User Manual Figure 3.20 802.1x Authentication Select “802.1x” to enter 802.1x authentication page. The 802.1x authentication needs a Radius server in LAN. In this page, you can input Radius server IP address, port number and secret key. Figure 3.21 3.5.
DSL Gateway/Router — User Manual Figure 3.22 Notice: You only can select one of allow mode or deny mode. 3.5.4 WIRELESS ADVANCED SETUP Press “Advanced” on the left menu to construct wireless security as Figure 3.23 Figure 3.23 4 OTHER CONFIGURATION 4.1 LAN CONFIGURATION 4.1.1 CONFIGURATION OF MODEM’S PASSWORD When you configure ADSL MODEM through an Internet browser, the system requires user name and password to validate access permission.
DSL Gateway/Router — User Manual Configuration column to change the password. Attention: please remember the password after change, otherwise you will not be able to change configuration after saving setting as Figure 4.1 Figure 4.1 4.1.2 CONFIGURATION OF MODEM’S IP ADDRESS As a network device, ADSL Modem has its own IP address and MAC address. The factory sets the MODEM, at a default IP address of 192.168.1.1 and subnet mask of 255.255.255.0.
DSL Gateway/Router — User Manual • click“Enable DHCP server” ； • Define the “Start IP address” and the “End IP address” of DHCP server (for example, from 10.10.10.11 to 10.10.10.254). • Input the value of Lease Time (Measured by the second, 0 indicates permanently valid). As Figure 4.3, open DHCP server, computer will set the IP Address of network card with one of the address 10.10.10.11 ～ 10.10.10.254. Figure 4.
DSL Gateway/Router — User Manual 3、 Try to run command “ping 192.168.1.1” on command line mode. If the response returns “time out”, please check Ethernet connection and IP settings; 4、 If this modem is reachable, try to run ping with a known outer IP, e.g. the DNS server IP of ShangHai Online: “ping 202.96.209.133”. If ping is reachable, there shall be no problems in the modem. Please see step 5; If ping is not reachable, see step 6 and check if the configuration is correct.
DSL Gateway/Router — User Manual ANNEX：SHIPPING LIST ADSL MODEM Splitter User Manual Power Supply Cable Cat5 RJ45 Telephone Line Warranty Certificate ×1 ×1 ×1 ×1 ×1 ×2 ×1 Page 21 Total 21 Pages
