On-Line Owner’s Manual Containing Cautionary FCC & IC Statements April 20, 2012 In-Line Hardwired Light Dimming Module Model: 2475DA1 FCC ID: SBP2475DA1 IC: 5202A-2475DA1 The owner’s manual below may be accessed freely via the Internet with any web browser and supports the PDF format. www.smarthome.com/2475DA1.html Complies with Section 5 of FCC document 784748 D01 Labeling Part 15 18 Guidelines v07 where cautionary statements in the user manual may be provided over the Internet.
In-LineLinc™ Dimmer INSTEON® In-LineLinc Dimmer, Dual-Band Owner’s Manual (#2475DA1) Page 1 of 14 2475DA1 - Rev: 4/20/2012 4:35 PM
In-LineLinc Dimmer Dual-Band ................................................................................................................. 3 Features and Benefits................................................................................................................................. 3 What’s in the Box?..................................................................................................................................... 3 Installation ...............................................
In-LineLinc Dimmer Dual-Band Congratulations on your purchase of the elegant, high-quality In-LineLinc Dimmer Dual-Band. In-LineLinc Dimmer Dual-Band installs in-line to provide INSTEON control of individual dimmable lighting fixtures. Additionally, In-LineLinc Dimmer Dual-Band eliminates the need for a conventional light switch, reducing the “switch sprawl” common to automation projects.
Installation CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. In-LineLinc Dimmer Dual-Band is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. Use indoors only.
Installing In-LineLinc Dimmer Dual-Band 1) At electrical panel, turn off circuit breaker(s) and/or remove fuse(s) feeding wall box. Verify the power is off. 2) Remove the fixture’s wallplate, unscrew the fixture and pull it out from the junction box. 3) Disconnect the wires from the fixture and In-LineLinc Wire Wall Box Wires ensure that you have ½” of bare wire on Ground 1 the ends. Bare copper (commonly bare green wire or 4) After ensuring wires are not touching, turn green screw) breaker(s) back on.
Using In-LineLinc Dimmer Dual-Band LEDs LED Meaning Solid green Load is on (at any dim level) Solid red Load is off Blinking green Unit is in linking mode Blinking red Unit is in unlinking mode Fast blinking red and optional blink-on-traffic is turned on Dimmer is off and INSTEON traffic received Fast blinking green and optional blink-on-traffic is turned on Dimmer is on and INSTEON traffic received Using the ON and OFF Buttons The small button switches allows you to test the load and function
NOTE: If In-LineLinc Dimmer Dual-Band’s Status LED is blinking, you held the Set button down too long and accidentally placed it into linking mode, which times out after 4 minutes of inactivity. To manually exit linking mode, tap any button except Set button. Beeper Behavior The In-LineLinc Dimmer Dual-Band features a built-in beeper which aids in programming and can also be used as an indicator via compatible software controllers.
Advanced Features Using In-LineLinc Dimmer Dual-Band as a Phase Bridge In-LineLinc Dimmer Dual-Band automatically bridges the electrical phases in your home to allow powerline-only INSTEON devices to communicate with RF-only INSTEON devices.
After a few seconds, In-LineLinc Dimmer Dual-Band will double-beep. The connected load will turn on. Local Ramp Rate The local ramp rate is the time it takes for the light(s) physically wired to In-LineLinc Dimmer Dual-Band to brighten from off to 100% brightness and vice versa. The default ramp rate is 0.5 seconds, but it is adjustable from 0.1 seconds to 9 seconds locally or up to 8 minutes using software such as HouseLinc. Ramp rate is determined using the brightness level of the load.
Specifications General Product name In-LineLinc Dimmer Dual-Band – INSTEON Remote Control In-Line Dimmer (Dual-Band) Brand INSTEON Manufacturer product number 2475DA1 UPC 813922012361 FCC ID SBP2475DA1 Patent number 7,345,998; protected under U.S. and foreign patents (see www.insteon.com ) Warranty 2 years, limited INSTEON INSTEON I.D.
INSTEON device category 0x01 INSTEON device subcategory 0x32 Mechanical Mounting Mounts inside standard electrical box in the ceiling or in the wall Colors: White – Neutral 18-gauge Black – Hot 16-gauge Wires Red – Load 16-gauge Copper – Earth ground 16-gauge Set button 1 Beeper Yes LED Dual-color green and red Dimensions 2.75" H x 1.75" W x 0.88" D Weight 120 grams / 0.
Maximum load 400 Watts Load type(s) Wired-in incandescent lighting Retains all settings without power Yes, all saved in Non-volatile EEPROM Standby power consumption < 1 watt Safety approved ETL (Intertek Testing Services) Certifications FCC, IC Canada Page 12 of 14 2475DA1 - Rev: 4/20/2012 4:35 PM
Troubleshooting Problem In-LineLinc Dimmer Dual-Band won’t control the load and the Status LED is not turning on. In-LineLinc Dimmer Dual-Band won’t add to a scene or respond to a controller. In-LineLinc Dimmer Dual-Band is taking a long time to respond to a controller. The load turned on by itself. Possible Cause Solution Make sure the circuit breaker is turned on. In-LineLinc Dimmer DualBand may not be getting power.
Certification and Warranty Certification This product has been thoroughly tested by Intertek ETL, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S.