On-Line Owner’s Manual Containing Cautionary FCC & IC Statements March 6, 2012 Wireless Remote Control AC Dimmer INSTEON SwitchLinc 2-Wire Dimmer Model: 2474DWH SMART Wall Dimmer 2-Wire Model: 4742A3 FCC ID: SBP2474DWH IC: 5202A-2474DWH The owner’s manual below may be accessed freely via the Internet with any web browser and supports the PDF format. http://www.smarthome.com/2474DWH.
SwitchLinc™ 2-Wire Dimmer Owners Manual #2474DWH Page 3 of 32 2474DWH- Rev: 3/6/2012 10:13 AM
Product Requirements Document...........................................................................................................1 Installation ................................................................................................................................................5 Identifying the Electrical Wires in your Home..........................................................................................5 Installation .................................................................
Installation CAUTIONS AND WARNINGS Read and understand these instructions before installing and retain them for future reference. This product is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. Use indoors only. This product is not designed or approved for use on power lines other than 120V 60Hz, single phase.
Installation 1) 2) 3) 4) 5) 6) 7) 8) At electrical panel, turn off circuit breaker(s) feeding wall box (verify that power is off) Remove wallplate and unscrew the switch you are replacing and gently pull out Disconnect wires from switch1 Turn breaker on Use a voltage meter to identify the line and load wires which connected to the switch Identify ground Turn breaker back off Connect wires SwitchLinc Wire Bare copper Red Black Wall Box Wire (common colors) Ground (bare copper, green wire or green screw) Li
Local Control Follow these instructions to control the connected light/load (as well as responders, if any) from the dimmer paddle. SwitchLinc Paddle Top Bottom Tap Press & hold Double-tap LED On Brighten On ramped until release or 100% instant Off Dim Off Bottom ramped until release or off instant LED Off White Setup Local Settings Local On-Level The local on-level is the brightness that the light physically wired to SwitchLinc will come on at when turned on at the SwitchLinc paddle.
Change LED Brightness (or turn it off) 1) 2) 3) 4) 5) Press & hold SwitchLinc set button until it beeps (3 seconds) SwitchLinc LED will begin blinking green Press & hold set button until it beeps again (3 seconds) SwitchLinc LED will start blinking red Press & hold set button until it beeps a third time (3 seconds) SwitchLinc LED will stop blinking SwitchLinc Status LED will illuminate at current LED brightness level Use the paddle to brighten or dim the LEDs to desired brightness a.
- If you wish the load to be off when link is activated (such as for an “all off” scene), turn the load off in step #2 Make SwitchLinc a Controller Follow the steps below to control a different INSTEON device from SwitchLinc.
7) Test by tapping controller button on and off SwitchLinc and other scene responders will all respond appropriately Add Multiple Responders 1) Press & hold SwitchLinc set button until beep LED will start blinking green 2) Tap SwitchLinc set button LED will start double-blinking green 3) For each responder you are adding - adjust responder to desired link/scene state - press & hold set button until double-beep (or LED flashes) 4) Press SwitchLinc Set button once SwitchLinc will beep once LED stops blinking
- press & hold set button until double-beep 5) Press SwitchLinc Set button once SwitchLinc will beep once LED stops blinking 6) Test by tapping the SwitchLinc on and off None of the former responders will respond Factory Reset NOTE: All settings and scenes will be erased 1) Pull set button out (creating an air gap) 2) Wait 10 seconds 3) Press the set button in as far as you can and hold SwitchLinc will begin a long beep 4) Continue pressing SwitchLinc set button until beep stops 5) Release set button Switc
Changing the Paddle and LED Colors You can remove the LED light pipes and/or front paddle and trim frame assembly before or after SwitchLinc is installed. During the changeover process, power and load may remain on and operating. There are no dangerous voltages or unsafe areas under the paddle.
Figure 4: Installed correctly Figure 5: Installed incorrectly 9) Gently place the paddle assembly back onto front of SwitchLinc. A little force may be necessary to snap the assembly over the Set button. Reinstall four screws that you removed in step 2.
Commands Supported as responder On Off Fast-on Fast-off Begin bright Begin dim End bright End dim Incremental bright Incremental dim Beep Go to specific brightness level Software Configurable Yes RF Range Up to 100’ open air Phase detect beacon No, RF only product INSTEON Device Category 0x01 Dimmable Lighting Control INSTEON Device Subcategory 0x24 X10 No X10 Support (RF only product) Mechanical Mounting Single gang electrical box Screw clamp connections Black – line (16 gauge) Re
Retains all settings without power Yes, saved in non-volatile EEPROM Standby power consumption < 1 watt Certifications FCC, IC Canada FCC ID SBP2474DWH Safety Approved ETL (Intertek Testing Services) Troubleshooting Problem Possible Cause Solution Make sure circuit breaker is on LED won’t come On SwitchLinc not getting power Check the junction box wires to ensure all connections are tight and no bare wires are exposed Check that a standard incandescent bulb is installed and is rated for 25-wa
Certification and Warranty Certification This product has been thoroughly tested by Intertek - ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S.