User's Manual

Quick-Start Guide
ACCESS POINT
TM
Set Button
Status LED
INSTEON-Compatible Access Point (#2443 & 2443P)
NNeeeedd HHeellpp?? FFoorr aassssiissttaannccee ccaallll yyoouurr
ssuuppppoorrtt ppeerrssoonn @@ 880000--776622--77884466
Access Points bridge RF-only INSTEON devices with power line-
only INSTEON devices and couple the phases of your home.
Installing Two Access Points
SStteepp 11..
Plug the
ffiirrsstt
Access Point into a convenient wall outlet.
For best performance when using a remote control place an Access Point in the
same room.
SStteepp 22..
On the
ffiirrsstt
Access Point tap the SET button four times rapidly.
The Access Point’s LED will turn bright and remain steadily on.
SStteepp 33..
Plug the
sseeccoonndd
Access Point into another outlet.
SStteepp 44..
Look at the
sseeccoonndd
Access Point’s Status LED:
• If it is
bbrriigghhtt aanndd sstteeaaddiillyy oonn
, go to step 5.
• If it is
bblliinnkkiinngg oorr ddiimm
, repeat step 3, trying another outlet.
NNoottee:: YYoouu mmaayy nneeeedd ttoo ttrryy sseevveerraall oouuttlleettss..
If you are unable to locate an outlet please call 866-243-8018
for assistance. If you have tried 5 outlets, go back and move the first Access Point to another outlet.
SStteepp 55..
Tap and release the SET button on the
ffiirrsstt
Access Point.
The Status LED on both Access Points will go dim and remain steadily on.
Congratulations! You have made your home INSTEON ready.
HINTS
• Do not use an outlet controlled by
a switch.
• Do not place near large metal
objects.
Troubleshooting Tips
•The Status LED on the Access Point is not turning on at all.
Make sure you are not on a switched outlet.
•Do not plug into a power strip or UPS (uninterruptible power supply).
•Add additional Access Points around the home to eliminate RF dead spots.
The advanced User's Guide can be found at
hhttttpp::////wwwwww..ssmmaarrtthhoommee..ccoomm//22444433..hhttmmll
.
SSmmaarrttLLaabbss LLiimmiitteedd WWaarrrraannttyy
SmartLabs warrants to the original consumer of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will perform
in substantial conformity to the description of the product in the owner's manual. This warranty shall not apply to defects or errors caused by misuse or neglect.
IINNSSTTEEOONN aanndd TThhee IINNSSTTEEOONN CCOOMMPPAATTIIBBLLEE llooggoo aarree ttrraaddeemmaarrkkss ooff SSmmaarrttLLaabbss,, IInncc.. UU.. SS.. PPaattnntt NNoo.. 77,,334455,,999988 ©© CCooppyyrriigghhtt 22000099 SSmmaarrttLLaabbss,, 1166554422 MMiilllliikkaann AAvvee..,, IIrrvviinnee,, CCAA 9922660066--55002277
880000--776622--77884466 wwwwww..ssmmaarrttllaabbssiinncc..ccoomm
rev. 090108
.
FCC Compliance Statement
This device complies with FCC Rules Part 15. Operation is subject to two conditions:
((11))
This device may not cause harmful interference, and
((22))
this device must accept any interference that may be received or that may cause
undesired operation. The digital circuitry of this device has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in residential installations. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio and television reception. However, there is no
guarantee that interference will not occur in a particular installation. If this device does
cause such interference, which can be verified by turning the device off and on, the user
is encouraged to eliminate the interference by one or more of the following measures:
•Re-orient or re-locate the receiving antenna
of the device experiencing the interference.
•Increase the distance between this device
and the receiver.
•Connect the device to an AC outlet on a
circuit different from the one that supplies
power to the receiver.
•Consult the dealer or an experienced
radio/TV technician.
WWAARRNNIINNGG!!
Changes or modifications to this
unit not expressly approved by the party
responsible for compliance could void the
user's authority to operate the equipment.