Quick Installation Guide

【Quick Installation Guide─RF Gateway and Fall Down Detector】

1 QIG GW-SD 11-2021 / v1.2

➢ Preparation

Equipment Required: SmartPhone or Laptop, WiFi Router

Application: Web Browser (Microsoft Edge/ Google Chrome/ Safari...)

9abcx-rf is only a sensor, so it must be combined with gateway 8811 to work

➢ Product Photo

Gateway (8811S-GW) Fall Down Detector

➢ Gateway Installation

1.1. Install Gateway：Power on the Gateway, the Indicator Light turns Red.

1.2. Indicator Light flashes rend and greed for next installation (AP-Mode)

1.3. Turn on WiFi Setting on SmartPhone/Laptop and connect to Gateway SSID. The format is

like ”SBI-GW-XXXXXXXXXXXXX”, and password ”12345678”.

1.4. Turn on web browser and enter“http://10.42.0.1:8000” (AP-mode connected address)

➢ Setting

1.1 RF pairing Process the pairing process for Gateway and Sensor

Press “RF pairing” on web browser and take a fine needle to press the pairing button at

the bottom left of the Detector around 2-5 seconds. The Indicator light flashes green

then take out the fine needle. The pairing process is done after the indicator light turns

solid green for seconds. The sensor number starts from {0}, followed by {1,2…7}. (Up to

8 ). Check it by “Find Sensor” ->” Online Sensor” after 30 seconds after pairing. (Section

1.6)

1.2 Remove all RF devices Remove all the pairing between Gateway and Sensors

Press ”Remove all RF” on web browser and all the pairing between Gateway and Sensors

are invalid.

1.3 WiFi Setting Connect Gateway to WiFi router and connect it by http:// <gateway

IP> :8000. (Client mode). Select the WiFi SSID and enter password of your router. It takes

3-5 minutes for WiFi setting. The Indicator Light turns to Blue after the WiFi setting is

completed. (Blue for Internet accessible; Red means Internet non-accessible)

1.4 API server address setting Modify the server address

You can configure the server address for data upload by this option.

(http://server IP). To upload the Gateway heartbeat and event record.

Please find the API document provided by SBI for more detail.

1.5 Read slip trigger log Read the fall down event record

You can check the time record table of fall down event from this option. It will keep the

last 50 data. The data will be completely removed and re-recorded after Gateway power

Indicator Light

Pairing

Button

Indicator

Light

Sensor

PAGE 1
【Quick Installation Guide─RF Gateway and Fall Down Detector】 ➢ Preparation ➢ Equipment Required: SmartPhone or Laptop, WiFi Router Setting 1.1 Application: Web Browser (Microsoft Edge/ Google Chrome/ Safari...) Product Photo Gateway (8811S-GW) Fall Down Detector 1.2 Remove all the pairing between Gateway and Sensors 1.3 WiFi Setting Connect Gateway to WiFi router and connect it by http:// :8000. (Client mode). Select the WiFi SSID and enter password of your router.
PAGE 2
【Quick Installation Guide─RF Gateway and Fall Down Detector】 on again. *Reminder~ 1.6 Find Sensor Check all the pairing list and status of Gateway and Sensors The sensor needs to be installed at a Online sensor: The sensor list for pairing to Gateway and online. Ex: Sensor {0} distance of 40~50 cm from the Offline sensor: The sensor list for pairing to Gateway and offline. NULL means none. ground to produce a 35 degrees Not paired: The sensor list that are not paired with Gateway.
PAGE 3
【Quick Installation Guide─RF Gateway and Fall Down Detector】 -- Increase the separation between the equipment and receiver. [ Warning ] Herty, Smart Bridge Information Inc. declares that this 8811S-GW&9202N-RF is in compliance with the essential requirements and other relevant provisions of Of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.