Torque Wrench CETOP-ZC-101W & CETOP-ZC-202W Manual Ｖｅｒ．１２．１（２０１８．１０）
Introduction Thank you for your purchase of "Digital torque wrench ". This software allows you to save taken out and it is possible to make various settings for the " Digital torque wrench " , work record that has been recorded in the torque wrench . In addition , the software and the "real-time monitor " can be taken out of the torque data and angle data (OP) in real time , you can use a wide variety of data analysis.
Traceability control system PC software Contents ・・・・・・・・・・・・・・・・・・・・・・・・・・ 2 3．Preparations for PC ・・・・・・・・・・・・・・・・・・・・・・・・・・ 3 4．Communication and connection settings ・・・・・・・・・・・・・・・・・・・・・・・・・・ 6 1．Overview 2．PC software 4-1) Connect the torque wrench(receiver) to the PC with the USB cable 4-2) Type of wireless receiver ・・・・・・・・・・・・・・・・・・・・・・・・・・ 7 ・・・・・・・・・・・・・・・・・・・・・・・・・・ 8 ・・・・・・・・・・・・・・・・・・・・・・・・・・ 9 4-3) Communication and connection settings 5．PC software and preparation 5-1) Starti
Traceability control system PC software 1．Overview This software is a tool for you to easily take advantage of the traceability management function of the torque wrench. You can load and save work data and various settings of the torque wrench. In addition, equipped with Excel conversion function, it is equipped with the easy-to-use function to another. 2．PC software 2-1) Setting operation Make the various settings of the torque wrench. Describe the function by major setting items below.
Traceability control system PC software 3．Preparations for PC 3-1) Compatible OS Microsoft Windows 2000 ・ Me・ XP ・ XPx64 ・ Vista ・ Vistax64 Microsoft Windows 7 ・ 7x64 ・ 8 ・ 8x64 ・ 8.1 ・ 10 ※It requires the installation of Microsoft .NET Framework 3.5. ☞ Point Please go on with administrator privileges software installation. 3-2) Installing USB drivers Installing USB drivers for torque wrench and receiver. (1) Load the supplied with the torque wrench. (2) Run the < CDM v2. **.
Traceability control system PC software Click 3-3) Installing PC software Install PC software (1) Run the "setup.exe" program of < SWrench.NET_PC Software > folder in the supplied installation CD. (2) Start the setup while following the on-screen instructions. Display Procedure It is Preparing to Install. Please wait. Click the . Specify the destination folder. If there are no changes, please click on the "Next" button.
Traceability control system PC software Display Procedure Please click on the "Install" button. To start the installation. It is during the installation. Please wait. The installation is complete. Please click on the "Finish" button. If the installation was successful , it is added to the < All Programs > , a shortcut icon is created on the desktop.
Traceability control system PC software 4．Communication and connection settings 4-1) Connect the torque wrench(receiver) to the PC with the USB cable HTW: Grip end DPW: Inside the cap on the Back Display Procedure Please connect the torque wrench or wireless receiver. It is recognized automatically. Confirmation of the COM number USB Serial Port (COM**) will be created in Ports (COM&LPT). When COM No. is between 1 and 16, the installation has been complete.
Traceability control system PC software Select a number on the list of COM Port Number: and click OK button to finish. 4-2) Type of wireless receiver ZC-101W I/O:USB mini-B/ D-Sub connector Early type Can be a USB connection to the PC. Shape: Box type Can be connected to devices such as Size:75×75×28 PLC / sequencer. ZC-201W Secure ZC-101W and compatibility. I/O:USB Type A Strong connection terminal.
Traceability control system PC software 5．PC software and preparation 5-1) Starting the software Please start . If you are using a < torque wrench > only the following, it will start directly < setting operation screen >. If you are using a < option function > at the same time the following, it will be displayed . Switch Button 5-2) Preparation of communication This section describes the procedures for performing communication between the torque wrenches.
Traceability control system PC software 2) Wireline・Wireless communication [Menu bar・communication Wireline/Wireless] [Wireline / Wireless]Icon (1) Wired connection completion ・・・・・ (2) Wireless connection completion ・・・・・ Wireless ID setting ・・・・・ *If the communication between the torque wrenches of the appropriate is successful icon is enabled.
Traceability control system PC software Display－Data output operation Data output operation icon Communication－Mode switching Displays screen. Changes the mode setting on the torque wrench when an operation is switched to another.
Traceability control system PC software 6．PC software Setting operation 6-1) setting operation 1) Overall Torque wrench data Pattern setting Mode setting 2) ＜Torque wrench data＞ (1)[Wrench type] Wrench type shows HTW-nn. (2) [Wrench name] The wrench name is set on screen (up to 8 alphanumeric characters). (3) [Unit code] The unique unit code can be set for each set of conditions (up to 8 alphanumeric characters).
Traceability control system PC software The field shows the tightening range that can be set on the torque wrench. (5) [Total number] The field shows the number of torque data sets stored in the memory of the torque wrench. (6) [Date] The date and time information which the torque wrench has recorded will be displayed. [Update] System time icon to display the time and date information on the PC. Date and time information by writing to the torque wrench will be updated.
Traceability control system PC software Enter an arbitrary number between 0 and 999. (4) [Next PT No,] A tightening condition can be set to automatically follow another condition. Up to 10 conditions can be registered. Enter the number of the pattern. * To repeat a condition, enter 0 for the condition. (5) [Memo mode] Invalid: Torque data will not be stored in the memory of the torque wrench. Valid: Up to 6,000 sets of torque data will be stored in the memory of the torque wrench.
Traceability control system PC software to move to next operation. Auto: After the tightening times have reached the set number, next operation will begin automatically. (5) [Wrench operation lock] (Only for HTW) Invalid: The settings can be changed on the torque wrench. (* There are restrictions. For details, see VII. Wrench operation.) Valid: The settings cannot be changed on the torque wrench. (6) [Date setting] Invalid: The time and date information of the set torque wrench is maintained.
Traceability control system PC software 3) Deleting torque data [Menu bar → Communication → Data deletion] [Data deletion]icon Deletes torque data on the torque wrench. 4) Saving PC settings [Menu bar → File → Save] ☞ Point 5) [Save] icon (Extension: .setting) Reading the settings [Menu bar → File → Open] [Open]icon 6-3) Optional feature Description 1) Angle wrench For angle-controlled bolt tightening.
Traceability control system PC software 2) ☞ Poka-yoke function Until it reaches a value that the torque value has been set, when the torque wrench in the “Specified angle " or more does not rotate , it is determined that had been tightening already in the " lower torque " , and warning . Work data is not recorded, will not be sent. Point "Specified angle" to be set depends on the conditions of the type and the bearing surface of the screw.
Traceability control system PC software 7．PC software Data output operation 7-1) Data output operation 1) Display of < output operation > ＜Menu bar＞ → Display → Data output operation ＜Data output operation＞Icon It will be displayed < output operation > screen.
Traceability control system PC software ＜individual detail of the wrench＞ Displaying torque wrench information Displaying setting conditions Displaying Data specification 3) ＜Screen switching tab＞ Switch the screen ＜Displaying torque data＞ and the screen ＜individual detail of the wrench＞ . 4) ＜Displaying torque wrench information＞ The content is the same as "setting operation". 5) ＜Displaying torque data＞ Work / measured data is displayed.
Traceability control system PC software 7) ＜Displaying setting conditions＞ Setting the content of the data that has been working or measured is displayed. 8) ＜Displaying Data specification＞ Work or measured data items are displayed. ＜Torque data＞ ＜Torque and angle data＞ 7-2) Reading Torque data from torque wrench 1) It reads the data from the torque wrench.
Traceability control system PC software (2) PC display 2) Deleting torque data on torque wrench ＜Menu bar＞ → Communication → Memory delete ＜Memory delete＞icon Data in the torque wrench will be deleted. 7-3) Data editing and saving 1) Data editing You can edit the < name > item column or < operator > column of the loaded data. " PT01 " in the < name > column 2) Click the < operator > column Editing of work or measurement "name" screen for data editing is displayed.
Traceability control system PC software 4) Change of the operator name Click the < operator > column. < Setting input > screen for data editing is displayed . Enter the work’s name to < operator > item, will be applied to the data in the "Apply" button. 5) Save the data ＜Menu bar＞ → File → Save ☞ Point 6) ＜Save＞icon The extension is“****.dat”. Reading of the stored data ＜Menu bar＞ → File → Open ＜Open＞icon 7-4) Optional feature Configure the settings of the output operation .
Traceability control system PC software 7-5) data transfer output transfer the data.
Traceability control system PC software 8．PC software Maintenance operation ☞ ☞ Point Point "Maintenance operation" is normally not displayed on the screen. When you start the program first, please start by holding down the "shift key" Communication shall be edited in mode. 8-1) Maintenance operation screen 1) Running Maintenance operation ＜Menu bar＞ → Display → Maintenance operation ＜Maintenance operation＞icon It will be displayed < Maintenance operation > screen.
Traceability control system PC software 8-2) Reading and writing of maintenance data Call the data from the torque wrench. ☞ 1), 2) of the order is required. Point 1) Remove the work data in the torque wrench. ＜Menu bar＞ → Communication → Data deletion ＜Data deletion＞icon Work and measurement data will be deleted in the torque wrench. 2) Reads data ＜Menu bar＞ → Communication → Reads data Maintenance information of the torque wrench is loaded.
Traceability control system PC software alert are activated continuously. Retention：It will work until it is canceled by manual operation. 7) Over torque counting function (Only for HTW) Do not count: When torque data has exceeded , does not count. Count: When torque data has exceeded , counts. * Please refer to the next page for details.
Traceability control system PC software See below for [Over torque counting function] and [Tightening direction].
低功率電波幅射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅 自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合 法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
FCC Warning 1. This device complies with part 15 of the fcc rules. Operationis subject to the following two conditions: (1) this device maynot cause harmful interference, and (2) this device mustaccept any interference received, including interference thatmay cause undesired operation. 2. NOTE: the grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. 3.
RF warning statement:Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
1 Oka, Okimura, Kitanagoya-shi, Aichi 481-8540 Japan TEL +81-568-21-1111 FAX．+81-568-23-4711 Smart Automation R&D ：1 Oka, Okimura, Kitanagoya-shi, Aichi 481-8540 Japan TEL．+81-568-21-2294 FAX．+81-568-25-4295 Web: http://www.smartautomation.jp/ E-mail: sa@sanyo-machine.co.
