User's Manual

ManualsBrandsSmart Technologies & Investment ManualsElectronicsWireless Sensor

User Guide

Wire-Free Home Protection System WS100S

Contents

Section 1 – Getting Started

1.1 Introduction to the System

1.2 Items included with the System

1.3 Introduction to the Smart Panel WS101

1.4 Introduction to the Smart Panel Backlight

Section 2 – Installing the Wire-Free Home Protection

System WS100S

2.1 Installing the Smart Panel WS101

2.2 Powering up the Smart Panel WS101

2.3 Understanding the Battery and AC Adaptor Symbols

Section 3 – Using the Wire-Free Home Protection

System WS100S

3.1 Program your 4-Digit PIN

3.2 Transmitting the Alarm Signal without a Siren

3.3 Operating different Modes

Section 4 – Installing the Sensors

4.1 Introduction to the Sensors

4.2 Installing the Sensors

4.3 Powering up the Sensors

4.4 Installing the Code Connectors

Section 5 -- Troubleshooting

5.1 FQA

5.2. Troubleshooting

5.3 Alarm System Limitations

Section 6 – General Information

6.1 Product Information

6.2 Specifications

6.2.1 Smart Panel WS101

6.2.2 4-Button Key Fob Remote WS101TX

6.2.3 Door/Window Magnetic Sensor WS102

6.2.4 Motion Sensor WS103

3.3.3 ALERT Mode

A. Entering the Alert Mode

B. Triggers in Alert Mode

3.3.4 HOME Mode

A. Entering the Home Mode

B. Triggers in Home Mode

3.3.1 STANDBY Mode

3.3.2 ARM Mode

A. Arming the System

B. Disarming the System

C. Zone Settings

D. Triggers in ARM Mode

Summary of content (16 pages)

PAGE 1
User Guide Wire-Free Home Protection System WS100S Contents Section 1 – Getting Started 1.1 Introduction to the System 1.2 Items included with the System 1.3 Introduction to the Smart Panel WS101 1.4 Introduction to the Smart Panel Backlight Section 4 – Installing the Sensors 4.1 Introduction to the Sensors 4.2 Installing the Sensors 4.3 Powering up the Sensors 4.4 Installing the Code Connectors Section 2 – Installing the Wire-Free Home Protection System WS100S 2.1 Installing the Smart Panel WS101 2.
PAGE 2
Section 1 – Getting Started 1.1 Introduction to the System The Wire-free Home Protection System WS100S is a high quality security system combined with user-friendly features that allow you to know the state of security of your home at all times. The System is managed by a Smart Panel, which gathers information from wireless sensors placed inside and at the entry points of your home. If the Smart Panel detects a security breach, you will be alerted via indicator lights and sounds.
PAGE 3
Programming Buttons: Function Buttons: ARM HOME ALERT Other: “9VDC INPUT” port For AC Adaptor (Included) Siren 120dB Buzzer Battery Compartment: Backup battery - 9V Alkaline Battery (Not Included) House code - Pin Header x 4, Jumper: x 4 “Reset” button - When you lost the 4-Digit, press: “Reset” and enter factory default password 1.
PAGE 4
Description 1 2 3 Note Insert backup battery (9V Alkaline – Not Included) Battery Voltage low level Plug in AC adapter to the DC socket System Entry “OFF” mode - You will hear one beep and the backlight will blink within 1 second (Yellow Red Green Yellow) - The Smart Panel will enter “OFF” mode after the automatic self - checking is complete. Then will appear on the LCD screen.
PAGE 5
Section 3 – Using the Wire-Free Home Protection System WS100S 3.1 Programming your new 4-Digit PIN Step 1 2 3 4 Keys 1234 Enter 1 4-Dight PIN Enter 4-Dight PIN Enter Description “Standby ” Mode Setting the new PIN Note You must be in STANDBY Mode.
PAGE 6
Step 1 Keys (1234 / 4-DIGIT PIN) + Description Note You must be in STANDBY Mode *To make sure you are in STANDBY mode: - Enter the default PIN 1 2 3 4 OR your new 4-Digit PIN - Press ENTER. - The LCD screen will display the below image: “Standby ” Mode (One beep indicates that you entered a valid PIN; Three beeps indicate that an invalid operation was performed). 2 4-DIGIT PIN Entry delay: up to 15 seconds * There is a 15sec entry delay time with a visual count down before the system is armed.
PAGE 7
Step Keys Description Note LCD will shown per below: 2 4-DIGIT PIN Enter 4-DIGIT PIN for setting 3 Press then to set the ARM mode 4 Press to Complete the setting (One beep indicates that you entered a valid PIN; Three beeps indicate that an invalid operation was performed).
PAGE 8
B.
PAGE 9
HOME mode default setting: Device Sensor Zone Status (MODE) WS102 Magnetic 1 ALERT WS102 Magnetic 2 ALERT WS103 PIR 8 ARM A. Entering the HOME Mode - First make sure the Smart Panel is in STANDBY Mode - On the Smart Panel: Enter your 4-Digit PIN + “ENTER” then press - On the Remote Control: Press to activate. B. Triggers in HOME Mode - Example: Zone setting: HOME Mode to activate.
PAGE 10
Section 4 – Installing the Sensors 4.1 Introduction to the Sensors The Wire-Free Home Protection System WS100S allows you to expand your system at any time. The System includes a range of sensors such as a 4-Button Key Fob Remote, a Door/Window Magnetic Sensor, a Motion Sensor, an Optional Auto Dialer, an Outdoor Bell Box, a Mat Sensor, a Garage Door Sensor, an Inactivity Sensor, and a Shock Sensor.
PAGE 11
- The transmitter and the magnet must be no more than 0.5mm apart. C. Mounting with the Double-Sided Adhesive - Ensure the mounting surface is clean. - Peel back one layer of the protective film and attach it to the transmitter. - Peel back the remaining layer of protective film and press the transmitter firmly in place against the mounting surface until firmly attached. - Repeat to attach the magnet. 4.2.
PAGE 12
4.3 House Code and Zone Setting The Wire-Free Home Protection System WS100S allows you can change the house security codes to avoid interference with different combinations. Step 1: Remove the battery compartment cover. You will find the 4 jumpers for setting the house security code. In most cases you will not need to change the factory settings for the house security code.
PAGE 13
Section 5 - Troubleshooting 5.1 FQA Q.1: What is the best way to set up my system? Where should I put my Smart Panel and the sensors? A.1: We recommend that you take some time in advance to think about the placement of the Smart Panel and Sensors. The best location for the Smart Panel is usually by the main entry/exit point, in a hallway, or in another central location in your home. The Smart Panel must be plugged into a power socket, which may dictate where it can be placed.
PAGE 14
5.2 Troubleshooting AC Power Failure: This may occur if your security system is accidentally unplugged or if there has been an AC power outage. If a full power failure occurs, please contact your electric company to find out the source of the problem. The backup battery will continue to run the system for approximately 6 hours. System Battery Failure: This may occur if the emergency backup battery has been drained and needs to be replaced.
PAGE 15
6.2 Specifications 6.2.1 Smart Panel WS101 Power source: Sensor Numbers: House code: Operating Frequencies: 9V Alkaline battery x1pc Unlimited 4 Jumpers 433.92MHz +/-0.5MHz 6.2.2 4-Button Key Fob Remote WS101TX Power source: RF Working transmission frequency: Transmission power: Buttons: House code: Wireless Range to Smart Panel: 12V Alkaline battery x 1pc 433.92MHz +/-0.5MHz > -45dBm(@12VDC, 1foot on the Lab table) “ARM”, “Home”, “Alert”, “OFF”; Panic function: “Home” + ”Alert” 4 Jumpers >50M 6.2.
PAGE 16
FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for and radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.