User's Manual

ManualsBrandsSmart Technologies & Investment ManualsElectronicsWireless Intercom (902MHz Tx)

Crystal clear two-way communication up to 500 feet wireless or 1000 feet with extended antenna.

Wireless Gate Entry Intercom/Keypad

Thank you for purchasing the GTO Wireless Gate Entry Intercom/Keypad. Be sure to read the

directions carefully and completely. Before permanently mounting the intercom/keypad, please

program the keypad and test its range.

IMPORTANT: Your intercom/keypad may need to be hard wired due to the fact that it must

accept interference according to FCC regulations listed below. For example, applications that

are relativity close to cell towers or airports may receive intermittent interference and require

hard-wiring.

In areas of high radio frequency (RF) interference, the keypad may need to be connected (hard

wired) directly to the gate opener using 16 gauge (AWG) stranded, direct burial, low voltage

wire (part no. RB509 not included).

Also in areas of high radio frequency (RF) interference, the intercom base unit may need to be

hard wired to the keypad using co-ax (cable TV cable not included) .

Instructions for Wireless and Wired Installations

ACCESS CONTROLS

GTO, Inc. • 3121 Hartsﬁeld Road • Tallahassee, Florida 32303

Telephone (850) 575-0176 • Fax (850) 575-8912 • website www.gtoinc.com

SAFETY NOTE: Never install the keypad portion of this unit where a person

can reach through the gate to activate it, or where a person can touch the gate

while activating the keypad. The recommended minimum distance between the

gate and keypad is 10 ft.

IMPORTANT: Allow the

intercom base unit’s battery

to charge for 12 hours before

using the system for the ﬁrst

time. See page 6 for details.

Summary of content (11 pages)

PAGE 1
® ACCESS CONTROLS IMPORTANT: Allow the intercom base unit’s battery to charge for 12 hours before using the system for the first time. See page 6 for details. Wireless Gate Entry Intercom/Keypad Instructions for Wireless and Wired Installations Crystal clear two-way communication up to 500 feet wireless or 1000 feet with extended antenna. Thank you for purchasing the GTO Wireless Gate Entry Intercom/Keypad. Be sure to read the directions carefully and completely.
PAGE 2
Features of the Intercom/Keypad The intercom/keypad has two separate units. The keypad (outside unit) should be mounted outside the gate allowing the driver of the vehicle approaching the property to press the CALL button from their vehicle. The base (inside unit), with it’s rechargable battery, can be plugged into any 110 Volt AC outlet for use while charging. It can also be disconnected from the charger allowing it to go any where within range for convenience.
PAGE 3
Keypad Description Keypad - Inside Keypad - Front $"--*/( ()* 134 (3"/5&% "#$ +,- 567 %&' ./0 89: 45"564 130(3". $"-- CALLING Light: LED is RED when calling and turns GREEN when call is answered. GRANTED Light: LED turns GREEN when access permissiom is granted. o DIP Switches: Match these switches to your remote transmitter to program the keypad. +6.1&3 2%,!9 /54054 !# $# 0/7%2 ).
PAGE 4
Step 2: For hard-wired communication between the keypad and gate opener, strip the wires back 3/16” and attach the wires to the terminal block marked RELAY OUTPUT on the keypad control board as shown to the right. Connect the other end to the opener’s control board as shown in Control Board Connections section below. Jumper OFF NOTE: For a hard-wired application the jumper between the two terminals on the keypad control board must be connected (ON) as shown. This will disable the 318 MHz RF transmitter.
PAGE 5
Programming the Keypad Programming Interface: Program (Add) New Temporary Entry Code: • • • • • Press and release PROGRAM button. • Enter the Master Code then press and release PROGRAM button. • Enter 8, and any number between 1 thru 7 then press and release the PROGRAM button.
PAGE 6
Delete ALL Entry Codes: Normal Keypad operation: • Press and release PROGRAM button. • Enter the Master Code then press and release PROGRAM button. • Enter 0, 7 then press and release PROGRAM button. • Beeper beeps 3 times to confirm that the All Entry Codes are deleted. • If the user enters a 4-digit code that is matched to one of the 25 stored codes, the STATUS light should blink twice and the beeper should beep twice to confirm that a matched code is entered.
PAGE 7
Intercom Base Unit Installation Connecting the Battery Remove the battery access cover using a small phillips head screwdriver. Plug the rechargeable Ni-Cad battery into the receptacle inside the battery compartment. See diagram to the right. When this is done, replace the battery access cover. ID S ET Battery Plug Battery Setting Intercom ID Codes In order for the Intercom(s) to communicate with the Keypad the ID Codes must be set.
PAGE 8
Adding Intercoms After Initial Installation Batteries must be installed and the units turned ON. ID SET button 1. Press the “ID SET” button on the Keypad until you hear a beep, then release. o +6.1&3 2. Press the number on the Keypad that corresponds to the Intercom you are adding or changing. For Example: If you are adding a third Intercom to the system PRESS #3. 2%,!9 /54054 !# $# 0/7%2 ). $"--*/( *% 4&5 3&4&5 o o ()* 3.
PAGE 9
Extending Antenna Range In areas of high radio frequency (RF) interference, the intercom may not work as a wireless system. In these areas the keypad antenna will need to be extended (run closer to the house) using co-axial cable, which is the same type of cable used for cable TV. You will need enough co-ax cable to run from the keypad location to a convenient location close to the house, but not closer than 30 feet from the intercom base unit.
PAGE 10
Test the System IMPORTANT: The base unit and the keypad can not be within 30 feet of each other when operating. If units are closer than 30 feet the signal will be inconsistent as well as emit speaker feed back. Have someone press the CALL button on the keypad at the gate. When the base unit inside the house rings, press the ANSWER button and talk to the person at the gate to check the connection and range.
PAGE 11
Hole Template for Mounting the Base Unit Limited One Year Warranty GTO, Inc. gate opener accessories are warranted by the manufacturer against defects in workmanship for a period of one (1) year from the date of purchase, provided recommended installation procedures have been followed.