Product Overview The CCS704WHD represents a combination of the highest quality camera and LCD components, combined with the most advance digital wireless communication technology available. The system operates at 2.4GHz. It uses Coded Differential Orthogonal Frequency Division Multiplexing (CDOFDM) technology to provide the highest quality, most secure, most reliable wireless signal available. The camera and LCD are paired together and the image from the camera can only be received on the paired monitor.
Features & Specification LCD701WHD Monitor size Transmission frequency Transmission resolution Transmission delay (ave) RF pairing Changeable channel Video frame rate Operating voltage Consumption Brightness Mirror image Speaker Contrast / Brightness Camera selection Dimensions (without sunshade) Weight Operating temperature 7.0’’ IPS-LCD monitor 2.4GHz (digital) High definition < 200mS Auto 125CH (overlapping hopping channel) 25fps / 30fps DC 9V-36V < 5.
Required Tool List Screwdrivers Marker pencil Drill Plyers Panel removal tool Soldering iron & solder Voltmeter Safety Glasses Supplied Parts list Wireless camera with power cable Wireless monitor with wiring harness Monitor stand Monitor sunshade Installation screws/clips Antenna rubber stoppers Set Antenna & Rubber Stopper This procedure can be used for both the camera and LCD: 1. Screw antenna on the base 2. Align antenna to allow it to point straight up. 3. Adjust antenna as desired.
Camera Installation The CAM150WHD Camera installation is simply a matter of bolting the camera onto the vehicle and supplying reverse power (DC 9V-36V). The only issue to take into account is mounting location. There are 3 main factors to consider: 1.Wireless Performance – The wireless communication cannot pass through metal so it is always better to try and install the camera near the top of truck or as low as possible so that the signal can effectively travel over the top or under the vehicle. 2.
Operation Instruction 1 2 3 4 Button 1: System functionality setting MENU Button 2: Selection/adjustment down Button 3: Selection/adjustment up Button 4: Record-Pause (Normal) / Setting enter (Menu) Button 5: System power ON-OFF / CAM-CH selection Page 6 5
To enter the system menu interface power on the screen, press the “MENU” button and use the “ ” or “ ” button to move the cursor to the required sub menu. Press the REC / ENT button to enter the selected sub menu. 1. System Pairing The purchased set will have been ‘paired’ during the assembly process so the initial operation should be as simply as power on the system monitor and camera.
2. Picture setting Select the “PICTURE” icon to enter the sub-menu setting interface a shown, then select and adjust the brightness, contrast, saturation and guideline feature. 3. Mirror-FLP Select the “MIR-FLP” icon to enter the sub-menu setting interface as shown, choose and select the correct mode. When used as a backup camera the image is MIRRORED, this is the default configuration. If the camera is not used for reversing, then the imager must be switched to NORMAL mode. 4.
5. CAMERA SETUP Select the “CAM-SETUP” to enter the sub-menu setting interface as shown. Choose and select the 4 cameras’ ON-OFF status, scan time and auto scan. The auto scan feature will continuously loop the picture display of multiply cameras. The cycling time interval displays can be adjusted using the scan time feature. 6. System Select the “SYSTEM” icon to enter the sub-menu settings interface as shown. Adjust the time/date, language, color system, auto dim, delay time and volume settings. 7.
8. Record Select the “RECORD” icon to enter the sub-menu setting interface as shown. Choose and select the rewrite and format settings. The initial use of a new SD card (not supplied) must be formatted prior to using the record feature. To use the record feature, select the CAM-CH to be recorded e.g. CAM1or for multiply CAM recording select the CAM-CH display mode combination e.g. CAM1/CAM2.
Wiring Diagram Page 11
FCC Declaration of Conformity This device complies with Part 15 of the RCC rules. Operation is subject to the following conditions, (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, the product may cause disruptive interference to radio communications.
Smart Park® Warranty Card PLEASE MAIL OR FAX THIS PAGE TO: Att: PERFORMANCE GUARANTEE DEPT.
Page 14