in-lite INSTALLATION MANUAL SMART HUB-150 INSTALLATION MANUAL SMART HUB-150 12 V Attention This product may only be used within the in-lite system. If components are used in the system that do not originate from in-lite, the warranty no longer applies. Install the in-lite system components (fixtures, transformers, mini-connectors, Easy-Locks and cable connectors) so that they can easily be replaced Never use the in-lite low-voltage cable directly connected to 100-230V.
in-lite INSTALLATION MANUAL SMART HUB-150 Contents 1x SMART HUB-150 INPUT : 230 V~, 50 Hz OUTPUT HUB-150: 12 V~, 12.5 A max., 150 VA Or, 1x SMART HUB-150 INPUT : 120 V~, 60 Hz OUTPUT HUB-150: 12 V~, 12.5 A max., 150 VA Dimensions 228 x 143 x 82 mm / 9.0 x 5.6 x 3.2 inches 2x screws Optional SMART MOVE (motion sensor) Please read the following instructions before installing. You are advised to keep these installation instructions in a safe place.
in-lite INSTALLATION MANUAL SMART HUB-150 Safety The external flexible cord of this product cannot be replaced; if the cord is damaged, the product shall be scrapped. When the transformer is connected in a wrong way (short circuit) or it encounters an overload, the “Off-led” will blink to signal the installer. Above a certain level of overload the transformer will shut down and reset itself. This procedure will loop until the connection has be done right or the load is reduced to an acceptable level.
in-lite INSTALLATION MANUAL SMART HUB-150 IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
in-lite INSTALLATION MANUAL SMART HUB-150 Installation The SMART HUB-150 is easy to install. After mounting the transformer and downloading and installing the in-lite application (app), the system is ready for connection. All lights can be controlled with the in-lite app on a smart phone or tablet. The app, which is suitable for an Android and iOS device, can be downloaded from the app store and installed on your device.
in-lite INSTALLATION MANUAL SMART HUB-150 Installation step by step Although the transformer is designed to withstand inclement weather, you are recommended not to place it close to a sprayer system. Place the transformer at least 50 cm above the ground and in the immediate vicinity of a 110V/230V electric socket. Installing the transformer (Fig. 5) Step 1 Open the package of the transformer. Here you will find the screws for fixing the transformer in place and the terminal lugs for the cable.
in-lite INSTALLATION MANUAL FIG. 1 FIG. 2 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 3 FIG. 4 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 5 www.in-lite.
in-lite INSTALLATION MANUAL SMART HUB-150 Installing the in-lite app Step 1 Open the app store on your Android or iOS device (smart phone or tablet). Search for in-lite and download the app. Step 2 Open the app on your device. You have two options to select; you’re a new user or you already have an account. (Fig. 6) FIG. 6 Step 3 Follow the instructions in the app. You’ll be guided through the process of logging in or creating your account.
in-lite INSTALLATION MANUAL SMART HUB-150 When you’ve created an account before you can log in with the code you’ve got by email. (Fig. 17) It’s also possible to skip the set-up when it has already been done by someone else and you’ve got a share code. You use that code to log in. (Fig. 18) Step 4 After logging in or creating your account you can connect accessories; at this time the SMART MOVE is available. Select the option in the pull-down menu in the upper right corner of the screen.
in-lite INSTALLATION MANUAL FIG. 7 FIG. 8 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 9 FIG. 10 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 11 FIG. 12 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 13 FIG. 14 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 15 FIG. 16 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 17 FIG. 18 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 19 FIG. 20 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 21 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 22 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 23 www.in-lite.
in-lite INSTALLATION MANUAL FIG. 24 www.in-lite.
in-lite INSTALLATION MANUAL SMART HUB-150 Use Manual use Press the on/off button on the side of the transformer to switch between “ON” and “OFF”. When the transformer is switched to “ON”, the light settings in the device application (in-lite app) are activated. If one or more light sections (total 3) are set to “ON” they will be activated; the lights switch on. The light sections that are set to “OFF” stay deactivated. The first time while installing, all light sections will be set to ‘ON”.
in-lite INSTALLATION MANUAL SMART HUB-150 Troubleshooting tips The lighting does not switch on with any of the programs. Check that the transformer is correctly connected. If so, check the voltage at the electric socket (you can do this using a voltage tester). Check that the low-voltage cable is correctly wired to the transformer. Only a few lamps switch on. Check that the contacts of the fixture’s Easy-Lock have correctly pierced the insulation of the cable.
in-lite INSTALLATION MANUAL SMART HUB-150 Installation tips Tip 1 Use plenty of cable for the installation. In that case the cable will have enough length if the garden subsides a little. Tip 2 Insulate the cable ends with caps. You can do this by pulling the end three centimetres of cable apart and putting a cap on each end. You do not need to remove any insulation from the cable. Tip 3 When connecting the fixtures leave plenty of cable from the fixture.