Use And Care Manual

ManualsBrandsSmart Electrician ManualsDimmers & OutletsOutdoor 7-Day Heavy Duty Digital Timer

Outdoor 7-day Digital Heavy-Duty Timer 3C with 2 outlets 368-1726

125 V AC / 60 Hz

15 A / 1875 W resistive

15 A / 1875 W tungsten

8 A ballast

3/4 HP, 15 FLA, 90 LRA

2. Press HOUR and MINUTE to set ON time. To change from AM to PM,

press HOUR 12 times.

3. Press DAY to select the desired day (or days) for the ﬁrst ON time.

4. P ress PROG to display 1 OFF setting.

Display will look like this:

Repeat steps 2 and 3 to select OFF time and day(s).

To program additional ON/OFF cycles: Repeat steps above to create

additional ON/OFF cycles (2 ON-2 OFF, 3 ON-3 OFF, etc.) up to a maximum

of 20 different ON/OFF cycles.

Once all ON/OFF cycles are programmed correctly, press CLOCK to exit

programming mode.

To program the ﬁrst ON/OFF cycle:

1. Press PROG to display 1 ON setting.

Display will look like this:

SECURITY (RANDOM) MODE: To operate a

plugged-in appliance in a random pattern while

you are away (to simulate actual use and give your

home a lived-in look): With timer in AUTO mode,

press and hold the HOUR button 3-5 seconds until RND appears in the

upper right of the display.

In Random mode, the plugged-in appliance will operate in random cycles

approx. 10-26 minutes ON and 26-42 minutes OFF. The RND mode over-

rides all programmed settings.

To cancel Random mode, press and hold HOUR 3-5 seconds until RND

disappears from display. Timer will now function using your previously

programmed settings.

TO OVERRIDE THE TIMER: Press ON-OFF until desired timer mode is

displayed:

ON: Programmed settings will be overridden; the plugged-in appliance

will remain ON.

OFF: Programmed settings will be overridden; the plugged-in appliance

will remain OFF.

AUTO ON turns the appliance on immediately until the next programmed

OFF time. AUTO OFF keeps the appliance off and will turn appliance on at

the next programmed ON time.

Note: The timer allows a maximum of 20 different programmable ON/OFF

cycles.

PROGRAMMING THE TIMER

Press the R button with the tip of a toothpick or

similar object to clear the memory. Display will look

like this:

Set time/day: Press and hold CLOCK while you press HOUR and MINUTE

to advance the display to the correct time. To change from AM to PM, press

and hold CLOCK while you press HOUR 12 times. Press and hold CLOCK

while you press DAY until correct day is displayed.

BEFORE YOU BEGIN PROGRAMMING THE TIMER:

This timer has an internal backup battery to save all programming.

1. Plug timer into a wall outlet for 10 minutes to charge the

internal battery.

2. After 10 minutes, unplug timer and press R button with the

tip of a toothpick or similar object to clear the memory.

Day display

AM/PM display

Clock display

Countdown mode display

Minute set button

Clock set button

Hour set button

Program button

Timer mode button

Day set button

Random mode display

Daylight savings mode display

Timer mode display

Memory erase (R) button

RCL-CD button

10.

11.

12.

13.

14.

15.

TROUBLESHOOTING TIPS: If timer is not operating as desired:

• Check outlet for power.

• Check that appliance works... plug it directly into outlet with power.

• Check that timer is in correct mode.

• Check programmed cycles for conﬂicts and overlapping day/time settings.

• Don't exceed maximum wattage rating.

Note that a power surge, power outage or nearby lightning strike can

permanently disable the timer.

IMPORTANT! Review programmed ON/OFF cycles: Press

and hold PROG to scroll through all cycles. Stop at any cycle

you want to change. To change any programmed cycle: Press

HOUR , MINUTE, and DAY as needed to revise any individual

cycle’s ON/OFF times. To remove any unwanted programmed

cycles: Press RCL-CD and cycle will be deleted. Make sure

that the desired day/times selected for all ON/OFF cycles don’t

overlap any other ON/OFF day/time settings.

When ﬁnished programming desired ON/OFF cycles, press ON-OFF until

AUTO ON or AUTO OFF appears in display. AUTO ON turns the appliance

on immediately until the next programmed OFF time. AUTO OFF keeps the

appliance off and will turn appliance on at the next programmed ON time.

Timer must be in AUTO ON or AUTO OFF mode for programmed settings

to operate. Plug appliance (such as a lamp) into timer and plug timer into

wall receptacle.

IMPORTANT! Appliance(s) must be turned ON or be in the

ON position before plugging into timer.

CAUTION: Timer must be mounted in a vertical position with

the receptacles facing downward and at least 4.5 feet (1.4m)

above ground level (not meant to be immersed in water).

COUNTDOWN MODE: Allows a plugged-in appliance to remain ON or OFF

for a speciﬁed length of time. To operate timer in Countdown mode: with

timer in AUTO mode, press PROG to cycle through

all 20 possible ON/OFF cycles until display shows

either “d ON” or “d OFF.” Display will look like this:

Press HOUR and MINUTE to set desired length of time for the timer to remain

in Countdown mode (In this example, timer will remain in Countdown mode

for a period of three hours). Press CLOCK , then

press and hold down RCL-CD for 3-5 seconds

until CD ﬂashes in lower left corner of display:

Note: If Countdown mode is activated while timer is operating within a

programmed ON cycle, the plugged-in appliance will stay ON for the

speciﬁed countdown time and will turn OFF after countdown time has

elapsed. If Countdown mode is activated while timer is operating within

a programmed OFF cycle, the plugged-in appliance will stay OFF for the

speciﬁed amount of time and will turn ON after countdown time has elapsed.

After countdown time has elapsed, timer will resume programmed operation

at the next programmed cycle.

To cancel Countdown mode at any time, press and hold RCL-CD for 3-5

seconds until CD disappears from display. Timer will now function using

previously programmed settings.

DAYLIGHT SAVINGS MODE: Adjusts the timer one

hour ahead to accomm odate daylight savings. To

operate timer in daylight savings mode, press and

hold CLOCK for 3-5 seconds until time display

advances one hour and DST appears on the right side of display.

To cancel Daylight Savings mode, press and hold CLOCK for 3-5 seconds

until DST disappears from display. Clock will move back one hour and timer

will now function using your previously programmed settings.

MINUTE

CLOCK

HOUR

PROG

DAY

ON-OFF

DST

RND

RCL-CD

MO TU WE TH FR SA SU

AUTO ON OFF

DST

7 8 9 10

OFF

AUTO ON

RND

AUTO ON

OFF

AUTO ON

DST