Smart Com Portable Transceiver SCV08 AND SCU08 INSTRUCTION MANUAL “think smart” 471 Ballard Drive Melbourne, FL 32935 Phone: 321-751-9047 Fax: 321-751-9074 www.smartcommusa.
SAFETY INFORMATION Your portable contains a low power transmitter. Then the Push-to-Talk button is pushed it sends out radio frequency signals. The device is authorized to operate at a duty factor not to exceed 50%. In august 1996, the Federal Communications Commission (FCC) adopted RF exposure guidelines with safety levels for hand-held devices USE only the supplied antenna. Unauthorized antennas, modifications, or attachments could damage the transceiver and may violate FCC regulations.
• American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields- RF and Microwave. TO ENSURE THAT YOUR EXPOSURE TO RF ELECTROMAGNETIC ENERGY IS WITHIN THE FCC ALLOWABLE LIMITS FOR OCCUPATIONAL USE, ALWAYS ADHERE TO THE FOLLOWING GUIDELINES: • • • • Do not operate the radio without a proper antenna attached, as this may cause damage to the radio as well as cause the RF exposure to exceed the FCC limits.
INDEX Introduction………………………………………………………………... 5 Installation Battery Installation and Removal……………………………… 5 Antenna Installation and Removal…………………………….. 5 Transceiver Views…………………………………………………………. 6 Transceiver Details………………………………………………………… 7 Operation Turning Unit On……………………………………………….. 8 Channel Selection………………………………….. 9 Mode Selection…………………………………….. 9 Tone Selection……………………………………… 9 Busy Channel Lockout……………………………… 9 Transmitter Operation…………………………………………..
INTRODUCTION SCV08 and SCU08 are 8-Channel, State of the Art, and Synthesized Portable FM Transceivers. The SCV08 operates in the 136-174 MHz VHF band. The SCU08B operates in the 450-480 MHz UHF band. The SCU08 operates in the UHF band with a 4 or 1 Watt RF power output. The SCV08 operates in the VHF band with a 5 or 1 Watt RF power output.
TRANSCEIVER VIEWS Prog Mic Speaker Antenna Jack Hi/Lo Power Antenna On/Off/Volume CH Selector Squelch Control TX/Busy Indicator Function Belt Clip Mounting Speaker PTT Internal Mic Battery Release Charge Jack 6
TRANSCEIVER DETAILS The various controls and features are enumerated and pointed out in the views shown on page 5. ON/OFF/Volume Control-Turning this control in the clockwise direction turns the Unit On. Turning it further in the clockwise direction increases the volume. Channel Selector-This control is used to change the channel number. Squelch Control-This control is used to eliminate speaker noise and reduce battery drain while not receiving a transmission.
Battery- The BPSC1L -1is a rechargeable Nickel-Cadmium (Ni-Cad) type battery. Battery Charging Jack-This jack is used to recharge the battery. The WCSC7 Wall Charger (included with the Radio) will fully charge the battery in approximately 20 hours if either the radio is turned off or the battery is removed from the Unit. Be sure to reinstall the protective plug when the Charger is disconnected. Belt Clip- When not using the belt-clip; install the mounting screws in order to help ensure water resistance.
LED ON CONDITION GREEN Channel is Busy (in use); or not programmed (if the channel has not been programmed a beep will be heard every four seconds) RED PTT is pressed; transmitter is activated Flashing RED Battery is low when PTT is pressed. CHANNEL SELECTION Rotate the CHANNEL SELECTOR switch until the knob’s pointer is at the desired channel number. Each time the switch is turned to a different channel, a beep will be heard. MODE SELECTION Pressing the FUNC button changes the radio’s mode.
TRANSMITTER OPERATION WARNING: In some countries, a license may be required to operate. Do Not transmit on Unlicensed channels. WARNING: Do Not operate this Unit close to electrical blasting caps, or in an explosive Atmosphere such as fuel or solvent vapors, dust, etc. PROCEDURE 1. Select the desired channel. Monitor the channel for activity before transmitting. If the BUSY LED is ON and no audio is heard, the channel is busy with another tone code.
BATTERY INFORMATION GENERAL INFORMATION The Wall Charger will fully charge the battery in approximately 20 hours. The RSC21-7 Drop-In Rapid Charger will fully charge the battery in approximately 1.5 hours. These times are dependent upon the Unit being turned off or the battery is not installed. DO NOT use any other charger or damage to the Battery may occur. FOR LONGEST BATTERY LIFE AND BEST PERFORMANCE 1. Charge the Battery to full capacity: Approximately 20 hours with the Wall Charger or 1.
SPECIFICATIONS (Subject to change without notice) GENERAL Number of Channels Frequency Range SCV08 SCU08 Operation Bandwidth Channel Spacing 1-8 Channel Increments Size With Battery Metric (cm) Weight With Battery and Antenna Power Requirements Battery Voltage Current Drain Squelched (w/Power Save) Squelched (w/out Power Save) Rated Audio Transmit – 1 Watt VHF 1 Watt UHF Transmit – 5 Watts 4 Watts Antenna Impedance Speaker Impedance Frequency Stability Operating Temperature RECEIVER Sensitivity (12 dB SI
SPECIFICATIONS (CONTINUED) Intermodulation -70 dB Min (VHF) -67 dB Min (UHF) -40 dB Min 500 mW Min 10% T.H.D. Max Hum and Noise Ratio Rated Audio Output Audio Distortion @ 0.25 W RF Output Power VHF UHF Spurious/Harmonic Emissions 5W/1W, +1dB 4W/1W, +1dB -70dBc Min (VHF) -63dBc Min (UHF) Modulation FM Hum and Noise Audio Distortion +5kHz -40 dB Min. 5% Max For service, in or out of Warranty, send Unit to SmartComm USA, Inc.
TWO YEAR LIMITED WARRANTY. Smart CommUSA Inc.