Installation Guide

ManualsBrandsSloan ManualsBathroom Sink FaucetsOptima Polished Chrome Touchless Single Hole Bathroom Sink Faucet

Code No. 0816542

Rev. 3 (02/11)

SPOUT

TEMPERED

SUPPLY

O-RING

GASKET

RETAINER

NUT

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED ‡

1-1/2” (38 mm)

MAX. DECK

THICKNESS ‡

If a connection to separate hot

and cold water supplies is desired,

then a Bak-Chek

tee fitting (not

supplied) must be used prior to

connecting to the faucet.

13” (330 mm)

LONG FLEX HOSE

HOT

SUPPLY

COLD

SUPPLY

MIXING VALVE (Can Be

Set and Removed)

13” (330 mm)

LONG FLEX

HOSES

MODELS EAF-100/150

1.5 gpm (5.7 Lpm) Max. Flow Aerator

Faucets with Single Line Water Supply

MODELS EAF-100/150-ISM

MODELS EAF-100/150-ISM-DPU-IC

1.5 gpm (5.7 Lpm) Max. Flow Aerator

Faucets with Hot and Cold Water Supply

INSTALLATION INSTRUCTIONS FOR OPTIMA I.Q.

ELECTRONIC SENSOR ACTIVATED LAVATORY FAUCETS

LIMITED WARRANTY

Sloan Valve Company warrants its Optima EAF-100 and EAF-150 Series Electronic Hand Washing Faucets to be made of first class materials, free from defects of material or workmanship under normal use and to perform the service for which

they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts

hich prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty

extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the battery.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

FAUCET VARIATIONS

SPOUT

O-RING

GASKET

RETAINER

NUT

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED ‡

1-1/2” (38 mm)

MAX. DECK

THICKNESS ‡

EAF-100 Series

Adapter Powered, Sensor

Activated, Lavatory Faucets

EAF-150 Series

Battery Powered, Sensor

Activated, Lavatory Faucets

6-7/8”

(175 mm)

24º

2-3/8 (60 mm)

2-3/4 (70 mm)

POP UP — MODELS EAF-100/150-ISM-DPU-IC

ONLY

2-3/8

(60 mm)

‡ When installing the Faucet on a three (3) hole

sink, make sure that the center hole is large

enough to accommodate the Faucet shank. A 1-

3/16" (30 mm) minimum diameter hole is

required. NOTE: A 1-7/32” (31 mm) Diameter

hole is required if the deck is greater than 1/2”

(13 mm) thick.

5-9/16”

(142 mm)

-ISM

Integral Spout Mixer

-IC

-Click

Feature

-DPU

rain Pop Up

-P

Plug-in Transformer/Adapter

(EAF-100 Series)

-LT

Less Transformer/Adapter

(EAF-100 Series)

PRIOR TO INSTALLATION

Prior to installing the Sloan Optima EAF-100/150 Series Faucets, install the

items listed below. Also, refer to rough-in illustrations.

• Lavatory/sink

• Drain line

• Hot and cold water supply lines or pre-tempered water supply line.

Trim Plates

When the EAF Faucet is installed on a sink that has three (3) hole punchings, a

Trim Plate should be used.

Trim Plates must be specified and ordered

separately.

ETF-607-A

Trim Plate for 4” (102 mm) Centerset Sink

ETF-608-A

Trim Plate for 8” (203 mm) Centerset Sink

Important:

•

ALL PLUMBING SHOULD BE INSTALLED IN ACCORDANCE WITH APPLICABLE

CODES AND REGULATIONS.

•

FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.

•

KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT

COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON

COMPRESSION FITTINGS.

TOOLS REQUIRED FOR INSTALLATION

• 13 mm open end wrench for male end of flex hose

• 13 mm open end wrench or nut driver for faucet retainer nut

• 5/8” open end wrench for female end of flex hose (US)

• 3/4” open end wrench for female end of flex hose (International)

FAUCET ROUGH-IN

Summary of content (8 pages)

PAGE 1
Code No. 0816542 Rev. 3 (02/11) INSTALLATION INSTRUCTIONS FOR OPTIMA I.Q.
PAGE 2
1 - INSTALL FAUCET B Install Faucet with A Remove Nut, Faucet Retainer O-ring into the center hole in deck or lavatory — 1-3/16" (30 mm) min. hole required. Note: If installing the Faucet on a three (3) hole sink, a Trim Plate should be installed at this time. and Gasket. Do Not remove the O-ring from base of Faucet.
PAGE 3
5 - ACTIVATE FAUCET A Activate faucet by pressing the button one (1) time, then immediately step away. Faucet will run for four (4) seconds and the range will automatically adjust to it’s environment. Wait ten (10) seconds after water shuts off before using Faucet. B Activate Faucet and check for leaks. If Faucet does not function, refer to the Troubleshooting section of this instruction manual.
PAGE 4
OPERATION As the user's hands enter the beam's effective range, the beam is reflected back into the sensor receiver and activates the solenoid valve allowing water to flow from the Faucet. Water will flow until the hands are removed or until the Faucet reaches its automatic time out limit setting.
PAGE 5
ADDITIONAL FEATURES -Click FEATURE & SETTINGS The i.q.-Click feature is a button on the underside of the Faucet spout that allows the user to place the Faucet into the following function modes: Continuous Run, Temporary Off, Permanent Off and Auto Set Range Adjustment. Continuous Run — Water flows from 1 - 20 minutes constantly — for easy filling of sink, pail or for hygienic handwashing. Default setting is two (2) minute run time.
PAGE 6
SENSOR RANGE ADJUSTMENT FACTORY SETTING IS APPROPRIATE FOR THE MAJORITY OF APPLICATIONS AND SHOULD NOT REQUIRE RESETTING UNDER EXTREME CONDITIONS. 4x B A 2x + 1x5 Sec. -IC OPTION C 5 sec E D 1x( 8x 7x 1x, 2x,...,8x) 6x = factory setting 5x 4x 3x 2x 1x DISCLAIMER: Updated electronics have visible red and green LED. Original electronics have only red LED and range setting is reversed (1=longest, 8=shortest).
PAGE 7
TROUBLESHOOTING GUIDE 1. Problem: Cause: Solution: Cause: Solution: Faucet does not function. Adhesive packaging label affixed over sensor eye. Remove adhesive label from sensor eye. "Permanent Off" activated. Press button on Faucet throat one time. 2. Problem: Faucet delivers water in an uncontrolled manner. Cause: Faucet is defective. Solution: Contact the Sloan Valve Company Installation Engineering Department (see below). 3.
PAGE 8
PARTS LIST 1 Item Part No. No. Description 1 1.5 gpm (5.7 Lpm) Aerator Spray Head 2.2 gpm (8.3 Lpm) Aerator Spray Head 0.5 gpm (1.9 Lpm) Spray Head Throat Plate Assembly (Battery Models) Throat Plate Assembly (Plug-in Adapter Models) Throat Plate Assembly with i.q.-Click (Battery Models) Throat Plate Assembly with i.q.-Click (Plug-in Adapter Models) Battery Replacement Kit Faucet Mounting Kit Strainer (Filter) Mixer Handle Assembly and Cartridge Handle Repair Kit 90-264 VAC/6.