Installation Sheet

ManualsBrandsSloan ManualsBathroom FaucetsSloan BASYS 0.5 GPM Deck Mounted Bathroom Faucet with IR Sensor and Battery Power

Code No. 0816408

Rev. 8 (05/16)

INSTALLATION INSTRUCTIONS FOR ELECTRONIC

INFRARED SENSOR ACTIVATED LAVATORY FAUCETS

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and workmanship

for a period of three (3) years (1 year for SF faucets, special finish and PWT electronics and 30 days on PWT software) from date of first purchase. During this period, Sloan Valve

Company will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole

and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No claims will be allowed for labor, transportation or other costs.

This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does

not cover the life of the battery.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES

OF ANY MEASURE WHATSOEVER.

EFX-2XX SERIESEFX-1XX SERIES

EFX-150.500.0000

Model Shown

(High Model with Bowed

Crown and Water

Temperature Adjustment)

EFX-277.502.0000

Model Shown

(Mid LCD Solar Model with

Water Temperature Adjustment

and Scrub Time Display)

MODEL GUIDE OR BUILD YOUR FAUCET ONLINE AT WWW.SLOAN.COM

––––

Body Type Power Crown

Mix Sensing Flow Rate

Batteries

Base

Plate

Adapters

Drain

Pop-Up

– Hardwire Bowed . None Active IR

0.5 gpm (1.9 Lpm)

Multi-Lam Spray Insert

. Alkaline None None No

High – – .

Below Deck,

Mechanical

– – . – 4-inch US Plug-in Yes

Mid – – .

Below Deck,

Thermostatic

–

1.5 gpm (5.7 Lpm)

Aerated Insert

. – 8-inch UK Plug-in –

– – – . – –

1.5 gpm (5.7 Lpm)

Laminar Insert

. – – EU Plug-in –

– – – . – – – . – – Box Mount –

– Battery Solar .

Integral Side

Mixer

– – . – – – –

– – – . – – – . – – – –

– Solar Solar w/LCD . – – – . – – – –

Turbine – . – – – . – – – –

BASYS

™

EFX __ __ __ . __ _0_ ___ . _0_ __ __ __

Choose one from each column.

Any Application.

Any Environment.

™

Summary of content (12 pages)

PAGE 1
BASYS Any Application. Any Environment.™ ™ Code No. 0816408 Rev. 8 (05/16) INSTALLATION INSTRUCTIONS FOR ELECTRONIC INFRARED SENSOR ACTIVATED LAVATORY FAUCETS EFX-150.500.0000 Model Shown (High Model with Bowed Crown and Water Temperature Adjustment) EFX-277.502.0000 Model Shown (Mid LCD Solar Model with Water Temperature Adjustment and Scrub Time Display) EFX-1XX SERIES EFX-2XX SERIES MODEL GUIDE OR BUILD YOUR FAUCET ONLINE AT WWW.SLOAN.COM EFX __ __ __ . __ _0_ ___ –––– Body Type .
PAGE 2
PRIOR TO INSTALLATION • KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON COMPRESSION FITTINGS. Base Plates When the BASYS™ Faucet is installed on a sink that has three (3) hole punchings, a Base Plate should be used. Base Plates should be specified at time of ordering. EFX-20-A Base Plate for 4” (102 mm) Centerset Sink EFX-26-A Base Plate for 8” (203 mm) Centerset Sink Prior to installing the Sloan BASYS™ Series Faucets, install the items listed below.
PAGE 3
1 - INSTALL FAUCET A B Remove Nut and faucet retainer. DO NOT REMOVE the D-shaped gasket from base of faucet. NOTE: Do not remove sensor label until water is connected Install Faucet with faucet retainer into the center hole in deck or lavatory — 1-3/16” (30 mm) min. hole required. NOTE: If installing the Faucet on a three (3) hole sink, a Base Plate should be installed at this time.
PAGE 4
- START-UP SEQUENCE A B For Hardwire Models, Plug Adapter into receptacle. Remove label from sensor window. SENSOR LABEL ADAPTER Green LED TO FAUCET C Activate faucet by holding installation instructions approximately 1-1/2” (38 mm) in front of sensor window until RED LED turns on then remove instructions while faucet senses its surroundings. Wait for green LED on side of faucet. D Activate faucet and check for leaks. If faucet does not function, refer to the troubleshooting section.
PAGE 5
ADDITIONAL FUNCTIONS Function Steps to Activate Function Default Setting IR Clic IR Activation Cover IR clic approximately for 2 sec. until LED will flash GREEN 1x then remove finger from IR clic (Active for 5 sec.) –– –– 2 min. –– IR activation; Cover IR clic 2x - confirmation of the function is active by a couple flashes by the LED; to return to normal operation cover Cleaning Mode IR clic 1x or the faucet will automatically return to normal function after 2 min.
PAGE 6
2x + SENSOR RANGE1x ADJUSTMENT 5 sec 2x + FACTORY SETTING IS APPROPRIATE FOR THE MAJORITY OF APPLICATIONS AND SHOULD NOT REQUIRE RESETTING UNLESS UNDER 1x REFLECTION 5 sec OR LOW LIGHT. EXTREME SITUATIONS: HIGH A IR Activation (see page 5).To enter programming mode place finger on IR clic for 2 times then remove. Light on side of crown should blink red to indicate programming mode.
PAGE 7
BATTERY REPLACEMENT NOTE: Replace battery when LED1 indicator flashes red each time faucet is in use or when faucet stops functioning. LED1 is identified by the battery symbol. NOTE: Turning off water is not necessary. A Remove all four (4) AA-cell batteries from battery pack. E Insert four (4) NEW AA-cell batteries into battery pack assembly cartridge. NOTE: Insure batteries are installed with proper polarity. The cover of the case indicates polarity of batteries.
PAGE 8
REPLACING THE SOLENOID/FILTER NOTE: TURNING OFF WATER IS NOT NECESSARY, DUE TO INTEGRATED AUTOMATIC STOP VALVE. A Remove crown by loosening hex screw located on underside of spout and slide crown down and lift off. NOTE: Screw is captive within faucet body. UNLOCK B Remove battery pack assembly by lifting out of spout. E Insert new solenoid caddy at a 45° angle. F Rotate solenoid caddy clockwise to align with arrow, locking the unit and opening water path. G Reinsert battery pack assembly.
PAGE 9
REPLACE SPRAY INSERT NOTE: TURNING OFF WATER IS NOT NECESSARY, DUE TO INTEGRATED AUTOMATIC STOP VALVE. A Remove crown by loosening hex screw located on underside of spout and slide crown down and lift off. NOTE: Screw is captive within faucet body. D Install new insert. NOTE: If changing to a different flow rate solenoid caddy must also be changed. UNLOCK B Retrieve spray removal tool located near the spray insert. E Return spray removal tool to storage location.
PAGE 10
UPGRADE FAUCET FUNCTIONALITY A B Remove crown by loosening hex screw located on underside of spout and slide crown down and lift off. NOTE: Screw is captive within faucet body. Place new crown on faucet by sliding onto spout and tightening hex screw on underside of spout. NOTE: All electronics are fully encapsulated in the crown and thus protected from the environment and easy to replace or upgrade.
PAGE 11
TROUBLESHOOTING GUIDE 1. Red LED in spout does not blink 2 sec after battery installation. Battery placement incorrect or batteries have been discharged. Ensure alkaline batteries are installed properly. Check the orientation of each battery matches the positive (+) and negative (-) symbols shown on the battery compartment. 2. Faucet does not function. Adhesive packaging label affixed over sensor eye. Remove adhesive label from sensor eye. 3. Faucet delivers water in an uncontrolled manner.
PAGE 12
PARTS LIST Item # Part # 1 2 3A 3B 4 5 6A 6B 6C 7 8 9 10 11 12 13 14 15 16 17 18 Description Mid Mount Faucet Assembly Mid Mount Turbine Faucet Assembly Mid Mount Faucet Assembly with Mixer Mid Mount Turbine Faucet Assembly with Mixer High Mount Faucet Assembly High Mount Turbine Faucet Assembly High Mount Faucet Assembly with Mixer High Mount Turbine Faucet Assembly with Mixer 0.5 gpm/1.9 Lpm Multi-Lam Insert (includes insert, o-ring, 2.5 mm allen key and removal tool) EFX-1001-A 1.5 gpm/5.