User's Manual

ManualsBrandsSleepHalo ManualsElectronicsSleepHalo

Before using your SleepHalo™ we

recommend reading this guide to

prevent any damage that could occur

due to misuse.

We also recommend registering your

product on our website to activate your

2 year warranty.

Visit: www.sleephalo.com/register

Package Contents

Compatibility for Wireless Charging

SleepHalo™ has been designed to be compatible with Qi enabled phones. A list

can be found on our website.

If your phone is not wireless compatible it can still be used with your existing

wired charger by placing the plugged-in phone onto SleepHalo™. You will then

benet from the radiation protection offered by SleepHalo™.

SleepHalo™ Charger Base

Radiation Shield

LED Indicator

Power Adapter (UK)

1M Cable

SleepHalo™ User Manual V1.1 E&OE

Page 1 of 6

Summary of content (6 pages)

PAGE 1
Before using your SleepHalo™ we recommend reading this guide to prevent any damage that could occur due to misuse. We also recommend registering your product on our website to activate your 2 year warranty. Visit: www.sleephalo.com/register Package Contents 1M Cable Radiation Shield Power Adapter (UK) LED Indicator SleepHalo™ Charger Base Compatibility for Wireless Charging SleepHalo™ has been designed to be compatible with Qi enabled phones. A list can be found on our website.
PAGE 2
Connecting your SleepHalo™ Decide which side of the bed you wish to place your SleepHalo™, noting that the raised protection shield should be between you and the phone. On the underside of the product you can route the power cable in 2 directions. Choose which route is best, plug in the connector to the power port and clip the cable through the rebated area. Cable clipped into rebate in base. Power Port Non-slip feet avoid SleepHalo™ slipping or scratching the surface it is placed on.
PAGE 3
Using your SleepHalo™ To charge wirelessly, the phone must be placed onto SleepHalo™ with the screen facing up. The indicator LED on the side will change from red to blue once phone is correctly placed. Place the phone on the centre of SleepHalo™. Outline of phone Use logo for alignment LED Indicator If the red LED flashes, this indicates the phone is not aligned correctly. Fully remove and then replace. Correct charging can also be confirmed by checking the screen of your phone for the charge icon.
PAGE 4
How to position SleepHalo™ on bedside table When positioning SleepHalo™, position it so that when you are laying down you cannot see the screen of your phone. Radiation Shield SleepHalo™ has rubber feet attached to the bottom to prevent it slipping. If you have a phone with a magnetic back, then sticky feet can be purchased from our website to hold SleepHalo™ down. Sticky Feet can be applied here For further set-up information and Troubleshooting please visit our support page at www.sleephalo.
PAGE 5
Safety Information • Using a different power adapter other than the one supplied with SleepHalo™ is at your own risk. • Do not disassemble SleepHalo™, it is a sealed device. • Whilst the phone is charging do not cover. • Do not place anything other than your phone onto SleepHalo™. • Do not use outdoors or in damp conditions. • Unplug if SleepHalo™ is not used for extended periods of time. • If you can see damage to SleepHalo™ do not use. • To clean SleepHalo™ unplug and use a soft damp cloth.
PAGE 6
Declaration of Conformity (FCC) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired operation.