Welcome to your Sleep Number Bed ® X 4000 and 5000 model assembly instructions inside 45 80
35 70
55 Welcome and Congratulations Welcome and Congratulations, Congratulations on your purchase of The Sleep Number Bed by Select Comfort™! You’re about to join more than 5 million people who’ve traded their innerspring mattresses for the most innovative sleep surface ever.
2 Foundation Assembly ....................................pg 3 Mattress Assembly.........................................pg 11 Firmness Control™ System .............................pg 23 FCC Users Information ..................................pg 26 Mattress Care.................................................pg 31 Accessories.....................................................pg 33 Warranty and Comfort Club® .........................pg 35 u u u u u u u Sleep Number® bed.
Foundation Assembly If you are missing any items listed on the following page, please e-mail Customer Service at customerservice@ selectcomfort.com or call 1.800.472.7185 BEFORE YOU BEGIN X Carefully check the contents of your foundation boxes X Decide where to put your new bed X Make sure there’s an electric power source nearby for use with your Firmness Control™ System X Assemble your bed frame if you have one Your foundation should be assembled directly onto your bed frame or on the floor.
CONTENTS Carefully check the contents of your foundation boxes and compare with the list below. Each component is clearly labeled with the part name and part number.
1 CONNECT SIDE RAILS Push the components labeled A side rail and B side rail together. Joints fit tightly. Push firmly. B A 2 INSERT PIN Slide pins in, “T” end up. Push firmly.
3 INSERT SUPPORT/ END BEAMS Pin Pin For Twin, Queen and Eastern King models: – insert support beams with tabs up and textured side out. For Full and California King models: – insert labeled end beams followed by remaining support beams with tabs up. Joints fit tightly. Push firmly until top is flush. Expanded Queen models only Attach a corner bracket over each end before connecting to the side rail.
4 INSERT SUPPORT BEAMS Tabs up, match “A” end with “A” groove; match “B” end with “B” groove. Joints fit tightly, push firmly until top is flush. B A A B Slide the remaining he support beams into the next set of channels.
5 PLACE DECK PANELS Twin shown Slide panels in until they are flush on sides. Panels fit snugly, do not force. Queen shown Reminder King foundation consists of two Twins side by side. 6 PUT ON COVERLET Work on carefully, one corner at a time, position seam at head of bed. Expanded Queen coverlet will go over the corner brackets.
Foundation Frequently Asked Questions What if I can’t get my center support beams flush with the side rails? Make sure the letter on the center support beam matches the side rail. For example, the end of the center beam labeled “A” should connect to the side rail with the “A” on it. Additional force may be required. How can I get my pins in all the way? All pins are wider at one end and narrower at the other end. Make sure the “T” end is up and the narrow end goes into the side rail first.
Mattress Assembly 11
Mattress Assembly If you are missing any items listed on the following page, please e-mail Customer Service at customerservice@ selectcomfort.com or call 1.800.472.7185 BEFORE YOU BEGIN X Carefully check the contents of your mattress boxes X IMPORTANT NOTE Prepare your foam pad(s) If you purchased a bed with foam comfort pad(s), carefully open the pad(s) and set aside. At least 20 minutes of expansion time is needed.
CONTENTS Carefully check the contents of your mattress boxes and compare with the list below. Each component is clearly labeled with the part name and part number.
REMEMBER: Open the foam comfort pad(s) before you begin and let expand for 20 minutes. 1 POSITION MATTRESS COVER Foot Place on foundation or on existing bed platform. )PMFT )PMFT Make sure the holes in the bottom of the cover are at the head of the bed. 2 UNZIP MATTRESS COVER Set cover aside.
3 PLACE CORNER LOCKS Place one in each corner. Corner locks must go under the border wrap. 4 INSTALL FOAM BORDER WALLS Place long border walls along sides.
5 INSTALL NSTALL FOAM ORDER WALLS BORDER Place ace short border walls at the head ead and foot. Foot Make ake sure the foam border walls alls are connected securely and squarely. quarely. The border wrap should cover over the foam border walls. 6 INSTALL AIR CHAMBERS Place air chambers so the hose connectors face the head of the bed, and lay on bottom when inflated.
7 CONNECT FIRMNESS CONTROL™ SYSTEM Place the Firmness Control™ System on the floor at the head of the bed and plug in the power cord. For the Sleep Number® 5000 Bed you will also need to plug the power cord into the Firmness Control™ System. Key Step: Pass the hose marked ”L” through the hole on the left side of the mattress cover and connect to the left air chamber. Press hose connections together until they click. Then complete the right side.
8 INFLATE AIR CHAMBER(S) Using remote, inflate air chamber. For dual chamber models, repeat for second air chamber. Sleep Number® 4000 Bed Sleep Number® 5000 Bed Press L or R to activate and select a side. Press any button on the remote to activate. Press and hold the firmer button to begin inflating the mattress. For wireless remotes, press L or R to activate and select a side. Press the button several times to inflate to 20. Adjustments will begin after a slight delay.