User's Manual

ManualsBrandsSkytech II ManualsElectronicsRemote control transmitter

SKY-6601

INSTALLATION AND OPERATING INSTRUCTIONS

INTRODUCTION

This SKYTECH remote control system was developed to provide a safe, reliable, and

user-friendly remote control system for gas heating appliances. The system can be

operated thermostatically or manually from the transmitter. The system operates on

radio frequencies (RF) within a 20”range using non-directional signals. The system

operates one of 256 security codes that are user programmable; the remote receiver’s

code must be matched to that of the transmitter prior to initial use.

Review COMMUNICATION SAFETY SECTION under TRANSMITTER

section and THERMO SAFETY SECTION under REMOTE RECEIVER section.

These signal/temperature safety features shut down the fireplace system when a

potentially unsafe condition exists.

The transmitter operates on 2 AAA-size 1.5V

batteries. It is recommended that ALKALINE

batteries always be used for longer battery life and

maximum operational performance.

IMPORTANT: New or fully charged batteries are

essential for proper operation of the multi-function

transmitter. Insert 2 AAA-size 1.5V batteries into the

battery compartment on the back of the transmitter,

positioning the (+) and (-) ends of the batteries as

indicated on the casing. When the batteries are

inserted, the screen at right (with similar numbers)

will display.

Note: If a LOW battery icon appears on the

screen, check the position of the batteries; a

reversed battery will not activate transmitter.

Note: Due to the sensitive

temperature-monitoring components in the

transmitter, it may be necessary to allow the

transmitter to stabilize to room temperature

before accurate room temperatures are displayed on the screen. If the transmitter is

TRANSMITTER

SET

LCD DISPLAY

ROOM

Summary of content (8 pages)

PAGE 1
SKY-6601 INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio frequencies (RF) within a 20”range using non-directional signals.
PAGE 2
activated from a severe cold condition, it can take up to fifteen minutes for accurate temperature readings to appear. LCD DISPLAY SCREEN 1. LOW-Battery power is low. Replace batteries within two weeks. ON OFF 3 2. TIMER-Indicates time remaining TIMER THERMO F before system shuts off, when F 4 timer-programmed; 9-hour ROOM SET maximum setting. 5 3. MODE-Indicates operation PM FLAME MODE of system. ON indicates the system is on, either manually 6 or thermostatically.
PAGE 3
SETTING THE CLOCK ON OFF THERMO TIMER F ROOM F Slide down the plastic cover on the front of the transmitter to expose the “SET” buttons. The Slide cover protects the SET buttons from being changed accidentally. Close the cover after completing the following settings/programming. SET Flashing numbers on the display indicate the PM FLAME system is awaiting user input, such as using the UP and DOWN buttons to program a new setting.
PAGE 4
SETTING DESIRED ROOM TEMPERATURE This remote control system can be thermostatically controlled when the ON transmitter is in the THERMO mode OFF TIMER THERMO (THERMO must be displayed on the F screen). To set the DESIRED room F temperature, press the MODE button to place the transmitter into THERMO mode, ROOM SET then press the UP or DOWN button to select the desired room temperature. The PM FLAME highest SET temperature is 99° Fahrenheit (37° Celsius ).
PAGE 5
the temperature differential or “SWING” (1-3). See above for 1-3 “SWING” temperature valves. 3. To store the “swing number” press the SET button or allow 15 seconds to lapse, and the new “swing number” will be automatically programmed. MANUAL CHECK OF “SWING” OR TEMPERATURE DIFFERENTIAL The operation of the factory set “THERMO SWING” can be checked by adjusting the SET TEMP 2℉ above or below the room temperature. This will cause the system to turn OF or OFF.
PAGE 6
ON OFF THERMO TIMER F F ROOM SET PM The low battery icon on the left side of the LCD screen will appear when battery power has dropped significantly. At this time, approximately two weeks of battery power remains until the transmitter may experience partial or complete loss of functions. FLAME CHILDPROOF “LOCK-OUT” –(CP) This SKYTECH remote control includes a CHILDPROOF “LOCK-OUT” feature that allows the user to “LOCK-OUT” operation of the appliance, from the TRANSMITTER.
PAGE 7
THERMO UPDATING FEATURE -TRANSMITTER - (T/S -TX) This SKYTECH remote control has a THERMO UPDATING Feature built into its software. The THERMO UPDATING Feature operates in the following manner, but only in the THERMO MODES: The transmitter normally reads the ROOM temperature every 2 minutes checking the ROOM temperature against the SET temperature and then sends a signal to the receiver.
PAGE 8
uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.