User's Manual

ManualsBrandsSkytech II ManualsElectronicsRemote control transmitter

SKY-4001TH

INSTALLATION AND OPERATING INSTRUCTIONS

INTRODUCTION

SKYTECH’S remote control system was developed to provide a safe, reliable and

user-friendly remote control system for gas heating appliances. This all battery system

operates independently of household current. The system operates on radio

frequencies with a non-directional signals. The SKYTECH’S operating range is

approximately 20 feet range. The system operates on one of 256 security codes that

are user programmable; the remote receiver’s code must be matched to that of the

transmitter prior to initial use.

Review THERMO SAFETY SECTION under RECEIVER section. This high

temperature safety feature shuts down the appliance when a potentially unsafe

condition exists.

TRANSMITTER

This remote control SYSTEM

offers the user a battery-operated

remote control that operates most

millivolt gas valves used in some

heater rated gas logs, gas fireplaces

and other gas heating appliances.

The transmitter operates on Lithium

3V battery.

Before using the transmitter, install

the Lithium 3V transmitter

batteries into the battery compartment. (Use

caution that batteries are installed in the proper

direction)

KEY SETINGS

l ON -Operates unit to on position,

Manually ON.

l OFF -Operates unit to off position,

Manually OFF.

l SET -Sets temperature in thermo mod.

HOUSE

CODE

OFF

SET

BUTTON

BATTERY

COMPARTMENT

OFF

BUTTON

SET

UNIT

CODE

BUTTON

SET

OFF

FRONT

BACK

Summary of content (7 pages)

PAGE 1
SKY-4001TH INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION SKYTECH’S remote control system was developed to provide a safe, reliable and user-friendly remote control system for gas heating appliances. This all battery system operates independently of household current. The system operates on radio frequencies with a non-directional signals. The SKYTECH’S operating range is approximately 20 feet range.
PAGE 2
LCD – Liquid Crystal Display 1. 2. 6 F 1 2 ON 3 OFF 5 3. 4. THERMO 4 5. 6. Display Indicates CURRENT room temperature. ℉ OR ℃ Indicates degrees Fahrenheit or Celsius. FLAME/ON Indicates burner/valve in operation. THERMO Indicates remote is in THERMO operation. OFF Indicates burner/valve is off. Battery Indicates battery power is low. SETTING ℉/℃ SCALE The factory setting for temperature is ℉.
PAGE 3
THERMOSTAT FUNCTION F THERMO SETTING DESIRED ROOM TEMPERATURE This remote control system can be thermostatically controlled when the transmitter is in the THERMO mode (The word THERMO must be displayed on the screen). To set the THERMO MODE and DESIRED room temperature, Press the SET key until the LCD screen shows the word THERMO, then the remote is in the thermostatic mode.
PAGE 4
normal operating cycle of an appliance may be 2-4 times per hour depending on how well the room or home is insulated from the cold or drafts. The factory setting for the “swing number” is 1. This represents a temperature variation of +/-1° F (0.5℃) between SET temperature and ROOM temperature, which determines when the fireplace will be activated. This function is pre-set at the factory.
PAGE 5
SKY-4001LCD INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION SKYTECH’S remote control system was developed to provide a safe, reliable and user-friendly remote control system for gas heating appliances. This all battery system operates independently of household current. The system operates on radio frequencies with a non-directional signals. The SKYTECH’S operating range is approximately 20 feet range.
PAGE 6
LCD – Liquid Crystal Display 1. 2. 3. 5 1 F 2 ON 3 OFF 4 F 4. 5. Display Indicates CURRENT room temperature. ℉ OR ℃ Indicates degrees Fahrenheit or Celsius. FLAME/ON Indicates burner/valve in operation. OFF Indicates burner/valve is off. Battery Indicates battery power is low SETTING ℉/℃ SCALE The factory setting for temperature is ℉. To change this setting to ℃, first l Press the ON key and the OFF key on the transmitter at the same time this will change from ℉ to ℃.
PAGE 7
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.