Installation and Operating Instructions

ManualsBrandsSkytech II ManualsElectronicsWireless Remote Controller (TX)

Model: 4001-A

REV. 3-31-20 Page 1

INSTALLATION AND OPERATING INSTRUCTIONS

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION

INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE

INTRODUCTION

This remote control system was developed to provide a safe, reliable and user-friendly remote control system for gas

heating appliances. This all battery system operates independently of household current. The system operates on radio

frequencies with a non-directional signals. The systems operating range is approximately 20-feet. The system operates

on one of 10,000,000 security codes that are programmed into the transmitter at the factory. It is designed to be used with

millivolt gas valves as a dry contact switch.

The transmitter is an ON and OFF. There is an LED light that

will illuminate when pressing either ON/OFF button. It you do

not see the red LED light illuminate check the position of the

transmitter’s battery.

The transmitter operates on (1) 3V Button Cell (included)

that powers the RF signal. Before using the transmitter, the

3V battery must be installed into the battery compartment.

Tools Needed: Small jewelers screwdriver

To remove the battery holder from the bottom of the

transmitter insert a small jewelers screwdriver into the

notch at the bottom of the transmitter, then gently pry out

the battery holder out. Once it is started, it will pull out

with your ngers. Insert the 3-volt button cell battery in the

battery holder with the plus (+) side up. See the drawings at

the right.

It is recommended that CR2032 lithium battery always

be used for longer battery life and maximum operational

performance.

OFF

ON-OFF Buttons

FRONT

LED (Red) Light

MODEL:

BACK

FRONT

MODEL: 4001-A TX

Bottom of

Transmitter

Summary of content (6 pages)

PAGE 1
MODEL: 4001-A TX INSTALLATION AND OPERATING INSTRUCTIONS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE INTRODUCTION This remote control system was developed to provide a safe, reliable and user-friendly remote control system for gas heating appliances. This all battery system operates independently of household current. The system operates on radio frequencies with a non-directional signals. The systems operating range is approximately 20-feet.
PAGE 2
REMOTE RECEIVER The remote receiver operates on 4 AA-size 1.5V batteries. It is recommended that ALKALINE batteries be used for longer battery life and maximum microprocessor performance. IMPORTANT: New or fully charged batteries are essential for proper operation of the remote receiver. The remote receiver houses the microprocessor that responds to commands from the transmitter to control system operation.
PAGE 3
WALL MOUNTING RECEIVER Install (4) AA-size 1.5 ALKALINE batteries in the remote receiver. For best performance, remote receiver batteries should be factory fresh when installed. Very little battery power is required to operate the remote receiver, but the electronics are tuned to operate best when total battery output is greater than 5.3 volts. Four new AA batteries should provide a total output voltage of 6.0 to 6.2 volts.
PAGE 4
WIRING INSTRUCTIONS A qualified electrician or a gas technician who is familiar with the gas appliance and gas valves that will be operated by this remote should install the remote control system. Incorrect wiring connections WILL cause damage to the gas valve or electronic module operating the gas appliance and may also damage the remote receiver.
PAGE 5
SYSTEM CHECK ELECTRONIC IGNITION SYSTEMS • Slide the 3-position button on the remote receiver to the ON position. The spark electrode should begin sparking to ignite the pilot (the pilot may ignite after only one spark). After the pilot flame is lit, the main gas valve should open and the main gas flame should ignite. • Slide the button to OFF. The main gas flame and pilot flame should BOTH extinguish.
PAGE 6
Federal Communication Commission Interference Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.