User's Manual

ManualsBrandsSkytech II ManualsElectronicsREMOTE CONTROL TRANSMITTER

3002P Instruction

LCD DISPLAY

1. PROGRAM FOR: Flashes when programming days of week and periods of the day. When in

normal state, only current DAY displays. When programming or in PROGRAM mode, both day

and week will display.

2. DAY – Flashes when current day or day of week is being programmed.

3. PERIOD – Flashes when current period of day or period of week is being programmed.

4. MODE – Indicates operation MODE of system. ON indicates the system is on, either

manually or thermostatically. OFF indicates the entire system is turned off. THERMO indicates

the system will automatically cycle ON/OFF, depending on programmed SET temperature.

PROGRAM – Indicates the system is operating with PROGRAMMED settings.

5. START AT – Flashes when programming the time to turn system ON.

6. SET – Indicates desired SET room temperature, when in THERMO or PROGRAM mode.

7. 0F/ 0C – Factory programmed in 0F.( 0C indicates degrees in Celsius.)

8. TIME/TEMP – Displays the CURRENT room temperature. In same frame the current time will

display in AM or PM. You must depress the TIME/TIMER button to display current time.

9. LOW – Battery power is low. Replace batteries within 2 weeks.

10. TIMER – When displayed indicates countdown timer in operation.

11. OVERRIDE – Displays when “programmed”” SET temperature is overridden.

12. FLAME – Single or double flame symbol indicates burner/valve is operational.

13. HOLD – Displays when “programmed” SET temperature is overridden and will hold that

temperature until cancelled or next program period change.

14. CP – Displays when CHILD PROOF “LOCK-OUT” is engaged. Pressing the UP and TIMER

buttons together, engages CP.

15. SWING- Displays in SET frame when setting TEMPERATURE DIFFERENTIAL.

16. FAN – Indicates the fan is on (when fan blade displayed). OFF indicates fan is not in

operation.

Summary of content (6 pages)

PAGE 1
3002P Instruction LCD DISPLAY 1. PROGRAM FOR: Flashes when programming days of week and periods of the day. When in normal state, only current DAY displays. When programming or in PROGRAM mode, both day and week will display. 2. DAY – Flashes when current day or day of week is being programmed. 3. PERIOD – Flashes when current period of day or period of week is being programmed. 4. MODE – Indicates operation MODE of system. ON indicates the system is on, either manually or thermostatically.
PAGE 2
FUNCTIONS To operate the system, press the MODE button on the transmitter to select the operational MODE desired. 1. ON indicates the system is on, either manually or thermostatically. 2. OFF indicates the entire system is turned off. 3. THERMO indicates the system will automatically cycle ON/OFF, depending on programmed set temperature. 4. PROGRAM indicates the system will automatically cycle ON and OFF in the programmed mode depending on the 7 day/4 period program that is in memory.
PAGE 3
. After setting the current HOUR, press the SET button on the front of the transmitter, and the MINUTE digits will begin flashing on the LCD screen 4. To set the current MINUTES, press the UP or DOWN button setting the correct MINUTES. 5. After setting the HOURS and MINUTES, press the SET button on the front of the transmitter SETTING THE FLAME CONTROLLER 1. Following step 5 above, two flames, words HI FLAME will begin flashing on the LCD screen. 2.
PAGE 4
digits in the TIME and SET frames will begin flashing. This confirms CUSTOMIZED programs have been cancelled. 4. Push the SET button to return LCD screen to normal state or wait 10 seconds and LCD screen will return to normal state automatically. SWING (TEMPERATURE DIFERENTIAL) 1. To change the temperature “SWING” setting (1-3), press the AHEAD + BACK buttons simultaneously to display the current “SWING” setting in the SET TEMP frame. The word SWING will display on the LCD screen. 2.
PAGE 5
2. press the SET button to cancel the display of the time. SETTING THE COUNTDOWN TIMER This remote control can operate with a built-in, countdown timer when the transmitter is in the ON or THERMO mode (THERMO or ON must be displayed on the LCD screen). DOES NOT operate in PROGRAM MODE as times are pre-programmed into the transmitter. 1. Press the TIMER/TIME button on the transmitter for more than 2 seconds. The word TIMER and 0:15 flash on the LCD screen. 2.
PAGE 6
FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.