User's Manual

ManualsBrandsSKYDROID ManualsElectronicsR16 Receiver

SKYDROID R16

User Manual V1.0

Attention

This product uses the following terms to classify the potential hazards that may be caused by

improper operation.

Note: If not follow the instructions, it may cause property damage, major accidents and serious

injuries.

Warning: Misuse of this product may result in injury, damage or loss of property. Read the

manual carefully before using this product. This item is not a toy. This item is intended for use by

professional UAV operators and installers only. Donot use this product if you lack the knowledge

and expertise to install and maintain UAV radio equipment. Do not use unapproved or unofficial

components with this system. Operators must strictly follow the operation guides set forth in this

manual. Skydroid does not accept any liability for the use or misuse of this product.

1、Main purpose and scope of application

It is used to remotely operate helicopters, fixed wings, multi-rotors, vehicles, ships, etc. for video

image transmission (optional camera), data transmission, and control drone flight.

2、Specifications

Receiver Specification

Model No.

R16

Channels

Working Voltage

42V

RF Power

20DB

Size

76*59*11MM

Weight

90G

3、The composition of the model and its significance

Summary of content (12 pages)

PAGE 1
SKYDROID R16 User Manual V1.0 Attention This product uses the following terms to classify the potential hazards that may be caused by improper operation. Note: If not follow the instructions, it may cause property damage, major accidents and serious injuries. Warning: Misuse of this product may result in injury, damage or loss of property. Read the manual carefully before using this product. This item is not a toy. This item is intended for use by professional UAV operators and installers only.
PAGE 2
Number Annotation Number 1 Network port 6 2 Power and Sbus input 7 3 Type-C 8 MIPI 摄像头接口 4 TF slot 9 HDMI input 5 Button for binding 4、Port definition Annotation Uart 0 Uart1
PAGE 3
5、Environment conditions Pay attention A） Working temperature b） Storage temperature c） Relative humidity d） Atmospheric pressure e） Working environment should not contain explosive material or any corrosive or harmful gas may cause interference in the operation of the product. f） Always work under shelter to prevent rain, snow, wind, sand and dust contamination. 6、Working conditions Power supply and attentions H16 series uses a built in Li-ion battery.
PAGE 4
Part one Operation 1、Preparation and pre-checking before use Pay attention ① Check battery level.
PAGE 5
Part two Status bar ①②③④ ⑤ ⑥ ⑦ ① Icon for connecting internet by network port or USB ② Icon for connecting well between the TX and RX (icon in picture shows no connecting with RX) ③ Icon for Power level ④ Icon for Time ⑤ Icon for return ⑥ Icon for back home ⑦ Icon for back ground management/screen splitter Part three H16 Helper ① ② ③ ④ ⑤ ① ② ③ ④ ⑤ Switch the joystick operation mode of the remote control Check whether the value of each channel of the remote control is normal or not You can view MIPI,
PAGE 6
firmware, and modify the receiver’s serial port baud rate (password 999, it is only for professional debugging) Part four Binding operation ① After powering on the receiver, wait 3-5 seconds, then press and hold the receiver “SET”, and release “SET” when the white light flashes ② Enter the H16 helper, click on the “binding”, click on the “binding” (after the binding is successful, it will show “connected”) Part five Video/Image connection and settings ① The factory default setting is HDMI/MIPI mode, whic
PAGE 7
Part six Joystick calibration Click on the rudder value in the H16 helper to view, and refer to the value for calibration ① When the remote controlscreen is completely off, center the knob. Long press the C and D keys in the six-position switcher, then slide the screen up and wake up the screen ② Release the C and D keys, and long press the D key.
PAGE 8
③ Change the video source to RTSP Video Stream ④ Enter RTSP address of the video/image to RTSP URL Showing MIPI, HDMI video/image ① Enter “rtsp://192.168.0.
PAGE 9
Part nine How to share internet, video/image transmission and data/telemetry transmission ① Sharing network When the remote control is connected to the Internet via the USB wireless internet card, the hotspot of the remote control can be turned on for network sharing ② Sharing data transmission （1）Turn on the hotspot of the remote controller （2）Connect the hotspot by PC （3）UDP Open Mission Planner, choose the connecting way into UDP （4）Click “connect” and select 14550 for the port number and click “OK”.
PAGE 10
① ② ④ ⑤ ③ ⑥ （4）Download VLC exe. to show video/image （5）Open VLC and choose network streaming （6）Enter “rtsp://192.168.43.
PAGE 11
② ③ Q&A 1. Can the remote control install other apps? The permissions of the remote control are all open, and there is no special software or restricted software installation and uninstallation. 2. How does the remote control enter the fast charge mode? Only under using the original charger to enter the fast charge mode, and there is a text prompt on the lock screen interface 3.
PAGE 12
Please check if there is a hotspot connected to the remote control 3、Maintenance, servicing Storage for not using certain period Put H16/H16 Pro in a dry and ventilated area. No direct sun light to prevent harm to the internal li-ion battery. If store it over three months, it is highly recommended to put room temperature between 22℃to 28 ℃.