Installation Guide

ManualsBrandsSKYBELL ManualsElectronicsSLIM LINE II

. Fi 802.11 b/g/n, 2.4 GHz up to 150 Mbps-Wi

ompatible with CUpload speed of 2 Mbps is required.

Wi-Fi

. camera doorbell

sent may result in damage to the chime is not pre

Failure to install a resistor when a . demonstration

or performing a the doorbell when testing

e This is typically don chime. home doorbell-wired, in

Alarm.com.

SkyBell V1 and V2 cameras are not compatible with

SkyBell V1 and V2 Not Compatible

. platform Alarm.com

the with may not be compatible Alarm.com,

not purchased through s, Certain SkyBell HD camera

SkyBell HD Cameras

atform. pl

h as the SkyBell suc, other platforms and apps

• Alarm.com Slim Line II Doorbell Camera

• Alarm.com Wi-Fi Doorbell Camera, SkyBell-HD

Edition

ith Alarm.com:

following Doorbell Cameras are fully compatible The

s Doorbell Camera Alarm.com

Masonry anchors

•

Wall screws

•

Wall mounting bracket

•

NCLUDED MATERIALSI

on.for more informati alarm.com/doorbell

Visit time alerts.-receive real triggered automation rules and

Customers can also record doorbell triggered clips, set motion

all right from their app. – way audio -visitors via two

the door and speak to s

peaker, enabling homeowners to answer

integrated camera, PIR motion sensor, digital microphone and

a doorbell with an amera featuresEach Alarm.com Doorbell C

even more customers! easy to deliver front door awareness to it’s

– Fi Doorbell Camera and our new Slim Line -Wiour original – from

amera. Now with two options to choose Doorbell CAlarm.com

Your customers will always know who is at the front door with an

INTRODUCTION

INSTALLATION GUIDE ALARM.COM DOORBELL CAMERA

DEVICE COMPATIBILITY WITH ALARM.COM

Slim Line II Incompatible with SkyBell and Other

Platforms

The Slim Line II D

oorbell Camera is not compatible with

REQUIREMENTS

Power and Chime Type

10-30VAC, wired to a n in-home mechanical or digital

doorbell chime. Note: A Digital Doorbell Adapter must

be installed if a digital doorbell chime is present. See

below for more information.

WARNING: An in-line resistor (10 Ohm, 10 Watt) is

required when installing the doorbell camera without a

Slim Line II

Summary of content (13 pages)

PAGE 1
ALARM.COM DOORBELL CAMERA INSTALLATION GUIDE INTRODUCTION Your customers will always know who is at the front door with an Alarm.com Doorbell Camera. Now with two options to choose from – our original Wi-Fi Doorbell Camera and our new Slim Line – it’s easy to deliver front door awareness to even more customers! Each Alarm.
PAGE 2
Wi-Fi Doorbell Camera - HD and Slim Line Editions | Installation Guide Mounting The mounting plate affixes to a flat surface (a power drill may be required) and uses the existing doorbell wiring. The equipment is only suitable for mounting at Mobile App Download the latest Alarm.com Mobile App for iOS or Android (version 4.4.1 or higher for video streaming). heights ≤ 2 m. PRE-INSTALLATION CHECKLIST Working Doorbell Check A wired doorbell circuit is required to provide power to the doorbell camera.
PAGE 3
Wi-Fi Doorbell Camera - HD and Slim Line Editions | Installation Guide HARDWARE INSTALLATION Use Alarm.com Doorbell Camera Hardware Alarm.com’s Doorbell Camera hardware must be used: • Alarm.com Wi-Fi Doorbell Camera • Alarm.com Slim Line II Doorbell Camera SkyBell HD consumer hardware is not supported. Slim Line Doorbell Camera hardware is not supported on the SkyBell platform or other service provider platforms.
PAGE 4
Wi-Fi Doorbell Camera - HD and Slim Line Editions | Installation Guide Log In to the Alarm.com App network is named Skybell_123456789 (or Use the login and password for the account that will SkybellHD_123456789), where 123456789 corresponds to the device’s serial number. On iPhone or iPad, you have the Doorbell Camera. Select Add a New Doorbell Camera Navigate to the Doorbell Camera page by selecting the Doorbell Camera tab in the left navigation bar.
PAGE 5
Wi-Fi Doorbell Camera - HD and Slim Line Editions | Installation Guide motion. Reduce the number of motion-triggered clips Notes: by selecting the "Low" motion sensitivity setting. Navigate to the Customer Website Video Device Recording duration is typically around one minute. Clips are longer during an alarm or when a mobile user joins Settings page and adjust the "Sensitivity to Motion" slider to the “Low” position.
PAGE 6
Wi-Fi Doorbell Camera - HD and Slim Line Editions | Installation Guide POWER INFORMATION & TROUBLESHOOTING Wired Power Supply Power Supply Issues The Alarm.com Wi-Fi Doorbell Camera requires a wired power supply. The protection circuitry in doorbell transformers degrades over time and with use. This causes the power output of the doorbell transformer to drop.
PAGE 7
Wi-Fi Doorbell Camera - HD and Slim Line Editions | Installation Guide POWER CONFIGURATIONS No Chime – With Doorbell Camera – Resistor Required* *WARNING: This setup is designed for testing and demonstration purposes only. Failure to install a resistor (10 Ohm, 10 Watt) when a chime is not present may result in damage to the doorbell camera.
PAGE 8
Wi-Fi Doorbell Camera LED and Troubleshooting Reference Guide LED Pattern Key Solid Rapid double flash Flashing Alternating flash Normal Operation Green | Solid Ready and working normally Use the Alarm.com app or Customer Website to choose a custom color in place of default green. In Call mode A call has been initiated or is occurring. Starting up Please wait while the doorbell is booting up. Battery is charging Battery may charge for ~30 minutes after installation.
PAGE 9
Slim Line Doorbell Camera LED and Troubleshooting Reference Guide LED Pattern Key Solid Rapid double flash Flashing Alternating flash Pulsing Normal Operation Green | Solid Ready and working normally Use the Alarm.com app or Customer Website to choose a custom color in place of default green. In Call mode A call has been initiated or is occurring. Starting up Please wait while the doorbell is booting up. Battery is charging Battery may charge for ~30 minutes after installation.
PAGE 10
Warning： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 11
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
PAGE 12
Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
PAGE 13
RF Exposure Statement The distance between user and products should be no less than 20cm Operations in the 5.15-5.