Installation Instructions

Wall bracket
Chime
Screw Driver
Video Doorbell
LVD01 LDC01
Setup your Video Doorbell and Chime
Charge your Video Doorbell
Open the back cover,
plug in micro usb cable to
charge the camera.
Press and hold the
SET button until LED
light blinks to enter
the setup mode.
Open the APP to
add camera.
Following camera
voice navigation to
finish the setup.
Press and hold the
Set button until LED
light blinks
Press doorbell button
to pair with chime
Video Doorbell
Doorbell is the first entrance of the security
around your property. It can see any person at
your door or prevent crime wherever you go.
Items Included
Get to know your Video Doorbell and Chime Install your Video Doorbell
Pairing your Video Doorbell
1. Camera lens
2. Microphone
3. Light sensor
4. Doorbell
5. Sensor
6. Speaker
7. SET key
8. Micro USB plug
9. LED indicator
10. Set button
11. Speaker
Drill holes for wall
anchor placements
Insert wall anchors
Mount wall bracket
with screws
1.
2.
3.
4. Place the doorbell
on bracket.
6. Place the adhesive tape to the back of the
chime and stick to the wall in a suitable
location inside your home
5. Tighten the lock screw
with cross screw drive
45 mm 135 mm
78 mm
Wall Anchors Screws
5
6
1
2
3
4
7
8
9
11
10
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance
20cm between the radiator and your body. This
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC Compliance Statement available in the phone app at:
Settings > Legal & Compliance > Compliance
FCC STATEMENT
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le
présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
This equipment complies with IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
ce matériel est conforme aux limites de dose d'exposition aux
rayonnements ic rss-102 énoncées pour un autre
environnement.cet émetteur ne doit pas être situées ou
opérant conjointement avec toute autre antenne ou
l'émetteur.
IC CAUTION
LVD01 & LDC01