http://www.skspruce.com/ San Jose 1885 Lundy Ave., Suite 270, San Jose, CA 95131, USA Tel: +1 (408) 449-5604 WIM1200-20 CONFIGURATION MANUAL Hong Kong 15K International Industrial Centre, 2-8 Kwei Tei Street, Shatin, Hong Kong Tel: +852 26983874 Revision: 01 Issued on 2016-04-20 Chengdu A1, Tianfu Software Park, 1129 Century City Road, High-tech Zone, Chengdu, Sichuan, P.R.
No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without prior, express and written permission from our company, Inc. Our company reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of our company to provide notification of such revision or changes.
Contents Contents Preface ....................................................................................................................................................... 3 Audience ................................................................................................................................................ 3 Applicable Browers................................................................................................................................. 3 Documentation Structure .
Contents Preface Audience This manual is directed for the technical services workers from SKSpruce Technologies, users and related pateners. It introduces the basic parameter configuration and management on module. Applicable Browers The web page is applicable in Firefox, Chrome and Internet Explorer. Note: for a better user experience, please use the Internet Explorer 8 or above.
1 SSH Configuration 1.1 Default Username and Password After launching the WIM1200-20 module, three SSID (AU-WIFI, AU-WIFI-1 and AUWIFI-2) would open and their passwords are the last 8 characters of the serial number on module by default, which can be acquired in the label on it. Then the SSID is searchable and connected by Wi-Fi terminal device. The default SSH username is “admin” and the password is “5upS%k!”. Please see the figure 1-1 below. Figure 1-1 SecureCRT Login 1.
Note: the WEB configuration is recommended for terminal users instead of SSH configuration, which may induce configuration fault.
2 WEB Configuration This chapter introduces the basic WEB configuration for WIM1200-20 including login page, System Info, Wi-Fi Settings, Admin Password, Upgrade and Restart. 2.1 Page Login After launching WIM1200-20 module, three SSID (AU-WIFI, AU-WIFI-1 and AU-WIFI2) would open and their password is the last 8 characters of the serial number on module by default, which can be acquired in the label on it. Then SSID is searchable and connected by Wi-Fi terminal device.
Figure 2-2 This page displays the firmware version, serial number, MAC address, intranet IP, router, DNS and Internet IP, but the data of intranet IP, router and DNS are only visible under intranet connection. Firmware version: AmOS-4.5.4.050P00R01 Serial Number: 448E1C72A2B0 MAC Address: 44:8e:1c:72:a2:b0 Extranet IP: 10.10.23.56 Default route: 10.10.23.1 DNS: 192.168.10.3 Intranet IP:192.168.1.1 2.3 Wi-Fi Settings This page is used for configuring basic Wi-Fi information and DHCP Server.
Figure 2-3 Figure 2-4 2.3.1 Revisible Wi-Fi Information The revisible Wi-Fi information includes the SSID name, password and switch for each SSID (if selected it is ON and otherwise OFF), any changes of it would take effect on the 2.4G / 5G interfaces and their SSIDs at the same time. Note: the definition of the first SSID of the checkbox is different from others. It is used for hiding the SSID or not (once putting the cursor on the checkbox, there would be “Broadcast/Hide” like figure 2-3.
Maximum connected user amount: 16 under each radio permission and 32 for the overall unit. Deafult SSID name: they are AU-WIFI, AU-WIFI-1 and AU-WIFI-2 for both 2.4G and 5G. Default Wi-Fi password: the last 8 characters for all the SSID. Default Cipher mode: wpa2-psk+ccmp Default bandwidth rate limit: the utmost 1Mbps of uploading and downloading speed for each SSID and user. Default Wi-Fi mode: 802.11b\g\n mixed mode for 2.4G and 802.11a\n\ac mixed mode for 5G.
When the system detects the upgradable firmware like figure 2-7 below, the user can choose to upgrade in Local or Online column. The page displays Online upgrade first by default. For Local upgrade page, please see the figure 2-8 below. Figure 2-6 This page is used for the local upgrade for module system. First, the user needs to download the firmware to the local path from official website, then browse the object on this page and click “Upgrade Now”. It requires 3 to 4 minutes before completed.
Figure 2-8 The operation on this page is used for local upgrade. Note: please don not switch the power off for the good performance of firmware. 2.6 Restart This page is used for local restart in module. See the figure below. Clicking Restart means restart the module.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Guidance to the Host Manufacturer: 1. We hereby acknowledge our responsibility to provide guidance to the host manufacturer in the event that they require assistance for ensuring compliance with the Part 15 Subpart B requirements. The host manufacturer is responsible for additional testing to verify compliance as a composite system. 2.
