RFID Reader Module sd905 Integration Manual FCC ID QSS-SD905 IC:6215A-SD905 Author: SOCH Version: 1.
RFID Reader Module sd905 SKIDATA AG Untersbergstraße 40 A-5083 Grödig/Salzburg Phone: +43 6246 888-0 Fax: +43 6246 888-7 Internet: http://www.skidata.com e-mail: info@skidata.com Copyright © 2016 by SKIDATA AG. All rights reserved. All information in the following document is protected by copyright law. No part of this document may be reproduced without the written consent of SKIDATA AG.
RFID Reader Module sd905 1. Table of Contents 1. Table of Contents ....................................................................................................................................... 3 2. General ........................................................................................................................................................ 4 3. sd905 .............................................................................................................................
RFID Reader Module sd905 2. General Validity This manual describes the sd905 RFID Reader Module into hosts, e.g. the Coder LIGHT (CO LIGHT). Addressees This manual is written exclusively for specialists. The descriptions in this manual are intended for personnel trained by the manufacturer. The information in this manual cannot substitute the product training.
RFID Reader Module sd905 ESD (electro static discharge) protective measures CAUTION — — — Danger for electronic components due to electrostatic discharge. Improper handling of printed circuit boards or components can cause damages that lead to complete failures or sporadic errors. During installation and repair of the device, the ESD protective measures must be considered.
RFID Reader Module sd905 3. 3.1 sd905 Connectors of the sd905 Fig. 1: Connectors of the sd905, top side Fig.
RFID Reader Module sd905 3.2 — — — — — — Technical Characteristics Dimensions: Operating frequencies: Modulation: Pulse repetition rule: Supply Voltage: Operating Temperature: 93 mm × 51 mm 13,56 MHz ASK 100 ms typ. 5V −30 °C to +85 °C — Compatible with RFID data carriers supported by SKIDATA systems — Compatible with data carriers compliant to ISO 15693 and ISO 14443 3.3 Description The sd905 functions as a built-in interface between a SKIDATA device and contactless data carriers (RFID).
RFID Reader Module sd905 4. Antennas Fig. 3: sd571 Fig.
RFID Reader Module sd905 Fig. 5: sd611 Fig.
RFID Reader Module sd905 Fig. 7: sd647 Fig.
RFID Reader Module sd905 Fig. 9: sd682/1 Only the 13 MHz antenna is used with sd905; the 122 kHz antenna remains unused Fig.
RFID Reader Module sd905 Fig. 11: sd697/2 Only the 13 MHz antenna is used with sd905; the 122 kHz antenna (wired coil) remains unused Fig.
RFID Reader Module sd905 Fig. 13: sd733/2 Only the 13 MHz antenna is used with sd905; the 122 kHz antenna remains unused Fig.
RFID Reader Module sd905 Fig. 15: sd758 (Shortrange module) Only the 13 MHz antenna is used with sd905; the 122 kHz antenna remains unused Fig.
RFID Reader Module sd905 Fig.17: sd794 Antennas A and B Fig. 18: sd847 Antennas A and B The sd847 acts as an antenna, as an illumination and as a touch key. The antenna part is completely independent from all other parts.
RFID Reader Module sd905 Fig. 19: sd862 Antennas A and B The sd862 acts as an antenna, as an illumination and as an illuminated touch key. The antenna part is completely independent from all other parts. The square part is the illuminated touch key and may or may not be removed.
RFID Reader Module sd905 Fig. 20: sd872 The sd872 acts as an antenna and as an illumination. The antenna part is completely independent from the illumination.
RFID Reader Module sd905 Fig. 21: sd877 Antennas A and B The sd877 acts as an antenna and as an illumination. The antenna part is completely independent from the illumination.
RFID Reader Module sd905 Fig. 22: sd888 Antennas A and B The sd888 is equipped with a special connector which fits into X015 of the sd905 and will therefore be powered as a bridge circuit.
RFID Reader Module sd905 Fig. 23: sd901 Fig.
RFID Reader Module sd905 5. Integration into Devices 5.1 Integration into CO LIGHT Fig.
RFID Reader Module sd905 5.2 Integration into Ski Antenna Fig.
RFID Reader Module sd905 6. Labeling Using a permanently affixed label, the modular transmitter will be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The same applies to the IC (Industry Canada) identification number.
