iDEN Noise Figure 5dB or less @Gain 65dB(Uplink) 12dB or less @Gain 40dB(Uplink) VSWR 1.5 : 1 Input/output connector N-Type (Female) Input/output impedance 50Ω Power 108 ~ 127 VAC, 60Hz ※Option -40 to -60VDC 20 to 30 VDC
System specifications 3.1.2 Shape Items Standards Cabinet Indoor type RF connector Type(IN/OUT) N-Type Female Size (H*W*D) Weight 390*326*190 mm ※ iDEN(65/15) 390*326*210 mm ※ iDEN(65/25) 390*326*240 mm ※ iDEN(80/30) 18.5 Kg ※ iDEN(65/15) 20.iDEN 4. System Shape and Functions 4.1 System Shape The iDEN (Integrated Digital Enhanced Network) RF repeater was arranged to efficiently utilize component modules when operators compose and operate the iDEN service network. The iDEN RF repeater is basically installed on the wall, has a structure to be installed on a 19 inch rack as necessary, and is provided with ground terminals on the lower part of repeaters for grounding. < Fig. 4 > System shape 4.
iDEN Heat radiation fin Hinge < Fig. 5 > External appearance of cabinets 4.3.1 Latch Latches was made to improve airtightness in performing a role important for cabinet characteristics such as rain-proofing functions, vibration, etc. and to secure safety because of locks. It was made convenient in opening or closing doors with an automatic raising function of heads and was made to avoid swing by minimizing shaft gap of latches.
iDEN 4.3.2 Hinge This was designed by considering convenience and promptness when opening and closing cabinets during assembly and maintenance of cabinets and has 3 kinds of advantages such as a torque function, stopper function, and separated angle function. < Separated angle> Torque function realization A stopper function when opening cabinets Separation when opening cabinets < Fig.
iDEN equipment weight for safety during transportation. < Fig. 8 > Swing handle functions 4.3.4 Additional functions (1) A twist preventing sill Realized in door part was a twist preventing sill for preventing a twist phenomenon of repeater cabinets due to vibrations and external environmental factors after installation.
iDEN 4.3 System configuration and functions The iDEN (Integrated Digital Enhanced Network) RF repeater is composed of PSU(Power Supply Unit), RCU(RF Control Unit), Up / Down Converter Module, PAU(Power Amplifier Unit), Filter, and Isolator Check module. < Fig.
iDEN 4.3.1 PSU (Power Supply Unit) This is used to supply stable DC power to each device provided with active elements through A/D conversion and D/D conversion by receiving AC power, uses semiconductors for industry or higher in terms of major activation elements, is mechanically strong, and satisfies all electrical characteristics. A power used, it is supposed to receive 108~127VAC, convert to DC 3.8V, DC 7V, DC 12 and DC 27V, and then use it.
iDEN The up/down converter of Down Link was realized with a digital filter through conversion and A/D conversion with IF frequencies(62.5MHz) for the base station(EBTS) signals inputted through the LNA part. This picks up an excellent roll off characteristic with a digital filter, minimizes influence on other signals by intercepting other neighbor bands and signals, and is improved to remove and separate spurious waves.
iDEN 5. SYSTEM BLOCK 5.1 Block Diagram Block Diagram 5.2 Interpretation of Block Diagrams Filter is a cavity type that is connected to the donor ANT and service ANT of iDEN repeaters and has only the desired bands pass selectively among the base station(EBTS) signals and terminal signals received through antenna.
iDEN And, the Up Link takes a roll off characteristic of a SAW filter by converting RF signals at the inputted terminal to IF frequencies(70MHz) through LNA differently from the Down Link, minimizes influence on other signals by suppressing neighbor signals, and is improved to remove and separate spurious waves. PAU amplifies the iDEN signals to a proper output level with a module at the final step of wndrPrldml, pass through a filter, and then discharges it through ANT.
iDEN 6. NMS 6.1 NMS NMS is composed of RCU(RF Control Unit) and NCU(Network Control Unit) and plays a role to monitor and control the status of each module of iDEN repeater. The RCU(RF Control Unit) is connected to GUI through DEBUG port and can collect and control the status monitoring information of modules. NCU(Network Control Unit) enables the upper NMS(Ethernet) communication through the RJ45 port and can monitor and control status.
iDEN a. Turn on/off the ALC function setup through GUI. b. Compensate its difference when the forward output value is greater than the set level or less than 1dB. c. Compensate its difference when the backward output value is greater than the set level or less than 1dB. d. (2) Monitor the forward and backward output values every 1 second. References a. Forward and backward operations are independent of each other. b. It does not work during oscillation checkup. 6.3.
iDEN 6.3.3 (1) Oscillation Check functions Handling procedures a. Turn on/off the oscillation check function setting through GUI. b. Inspect the 798 ~ 799MHz section c. Measure the oscillation detection values while moving by 30KHz from the oscillation check frequency 798 ~ 799MHz. d. Find the minimum value and maximum value among the values measured in c. e.
iDEN 7. GUI (Graphic User Interface) 7.1 Program Installation Prepare the provided installation program in the same folder as below. Setup file Start program installation by double-clicking Setup.exe. Then, the following screen will show up. In order to cancel the installation, click [Cancel] in the right lower side, and in order to continue the installation, click [Next]. Installation Start Select a folder where the program will be installed. Basically, a folder called C:\Program
iDEN Selection of an installation folder When an installation folder is determined, click the [Next] button. Then, a window to inform you that the preparation for installation has been completed will show up as follows. Completion of preparation for installation In order to change an installation folder, click the [Back] button, go over to the
iDEN and then change the installation folder. In order to continue installation, click [Next] button. Then, a program is automatically installed as shown in . Display of program installation progress It is asked whether or not to install a USB driver. In order to install a USB driver, proceed with installation according to the installation procedure by clicking the [Install] button, and if a USB driver has been already installed, cancel the installation by clicking the [Cancel] button.
iDEN USB Driver Installation 7.2 Program Start If the program is properly installed, then go to Start->Program on the Windows menu and execute TSEX1100. Program start 7.3 Status Inquiry/Setting As soon as the program is executed, a serial port is automatically opened at a baudrate 38400bps.
iDEN 1 second interval. 7.3.1 Status Inquiry If the type in the left upper side is iDEN, an iDEN related item appears on the screen as shown in the figure below. An iDEN status inquiry screen Functions of each button are as follows. Port Open / Close Opening/closing a communication port Debug Opening a window to show communication contents Download Opening a download window Set Control setting Exit Program end 7.3.
iDEN An iDEN status setting screen 7.4 DOWNLOAD 7.4.1 Preparation for Download Clicking the Download button on the status/monitoring screen enables F/W Download. Clicking the Download button on the status/monitoring screen shows a window as shown in the figure below. A download preparation window Click the [File Open] button. If you want to end it, click the [Exit] button.
iDEN 7.4.2 File Open Clicking the [File Open] button shows a File Open window as shown in the figure below. File Open Find and click a file to download whose extension is ".bin” or directly enter the name of a file to download on the file name column and then click [OK]. Then, the file information(file path, file name, file size, total frame) will show up on the download preparation window as shown in the figure below.
iDEN 7.4.3 Download Start Clicking the [Start] button on the upper side of the above starts downloading and shows a download progress window as shown in the figure below to show the download progress situations. A download progress screen Pressing the [Cancel] button cancels download. If downloading is not properly realized, a warning window shows up as shown in the figure below. A message to notify you of download failure 7.4.
iDEN If all download processes are completed, a completion message appears as below.
iDEN 8. System Installation 8.1 Confirmation of System Components a. Check the following matters during installation for normal operation of equipment. b. Check existence of abnormality to see if the appearance of repeaters(RF connector), etc. was deformed due to damage to the repeater packing materials during equipment transportation. c.
iDEN 9. System Setup and Checkup 9.1 Check Items during Opening 9.1.1 (1) Check Items before Opening Check the normal power of AC108~127 VAC and then check existence of abnormality in power cables. (2) Check if the donor RF input signal from outside is in a normal level.
iDEN 9.2 Troubles and Checkup 9.2.1 Repeater Checkup When checking repeaters periodically or due to abnormality in service, check the existence of abnormality in the equipment according to the following sequence. (1) Confirm the RF input/output level of repeaters on NMS, LED of repeaters, etc.
iDEN Checkup parts Checkup items Check if there is no abnormality in the antenna Donor antenna and service attachment status and if the received signal antenna intensity of donor antenna and the RSSI value are good. Feeder cables, leakage coaxial Check if there is no feeder cable, leakage cables coaxial cable cutting, coating damage, etc. Check if there is no flooding phenomenon in Connectors, distributors connector connection parts and cables and if each connection part is rigidly tightened.
iDEN ☎ Contact place of the maker Maker Address Staff in charge of R&D Staff in charge of sales SK Telesys Co., Ltd.