Click Dome Draft | english | 2016-12-13 ConnexxAir User Guide
Content Before you start Included in delivery Components 3 4 5 Getting started Assembling the power plug Charging Turning on and off Installing the neckloop Connecting ConnexxAir 6 6 7 9 10 11 Programming with ConnexxAir Wearing ConnexxAir Programming on the table 13 14 15 Important safety information 16 Important information Status LEDs Troubleshooting Maintenance and care Explanation of symbols Operating, transport, and storage conditions Te
Before you start ConnexxAir is a wireless programming system for our specific wirless hearing instruments. Place ConnexxAir around your patient's neck and wirelessly connect your patient's hearing instruments to the programming software on the PC. No programming cables are necessary. Follow these instructions to set up ConnexxAir and to understand how ConnexxAir works. CAUTION Read this user guide thoroughly and completely and follow the safety information in this document to avoid damage or injury.
Included in delivery ➊ ConnexxAir ➍ Power plug, with different ➋ Charging cradle ➌ Neckloop (is also the antenna) adapters (depending on your country) ➎ USB power cable ➏ USB Bluetooth dongle 4 Draft | english | 2016-12-13
Components ➏ ➊ Power button ➍ Reset button (recessed) ➋ Status LEDs ➎ USB port for firmware updates ➌ Pairing button ➏ Battery compartment 5 Draft | english | 2016-12-13
Getting started Assembling the power plug The power plug comes with several country-specific adapters. Depending on your country you have to assemble the power plug with an adapter: X For US sockets, no adapter is required. Fold out the plugs (left picture). X For all other sockets, an adapter is required (right picture): Fold the plugs in and slide the adapter onto the folded plugs. The adapter clicks noticeably in place. You can now connect the cable with the power plug.
Charging ConnexxAir is partly charged on delivery. Charge it before first use and when the battery is low and the middle LED is flashing orange. Battery is low X Connect the charging cradle with the power plug to a power supply: X Carefully push ConnexxAir in the charging cradle. ConnexxAir is automatically turned off.
X When you take ConnexxAir out of the charging cradle, ConnexxAir is automatically turned on. Further information: ■ A fully charged ConnexxAir can be used for approximately 10 programming sessions before recharging is required. ■ Do not use ConnexxAir for programming while charging.
Turning on and off X Turning on: Shortly press the power button. The middle LED first shines green, then goes off. Left and right LED light up shortly. X Turning off: Press the power button until the middle LED fades off. The middle LED first shines green, then fades off.
Installing the neckloop The neckloop is the antenna for the wireless connection of ConnexxAir and the hearing instruments. X Insert both neckloop plugs all the way. Further information ■ If the neckloop is not plugged in completely, the programming software displays a warning message. ■ If the neckloop is disconnected for more than 15 minutes, ConnexxAir turns automatically off. ■ Some of our remote control units or audio streamers have similar neckloops.
Connecting ConnexxAir X Plug the Bluetooth®* dongle into an USB slot of your PC. X Turn on ConnexxAir: Press the power button. The middle LED first shines green, then goes off. Left and right LED light up shortly. If you are using ConnexxAir or a new dongle for the first time, ConnexxAir searches for the dongle - it is in pairing mode. All three LEDs flash green from left to right . X In the software for programming the hearing instruments (e.g.
The connection is automatically established: As soon as the connection to the PC could be established, the middle LED shines green for 3 seconds, then starts flashing. If the middle LED flashes slowly (once every 3 seconds), the connection to the hearing instruments could not be established. Refer to section "Troubleshooting". If the middle LED flashes quickly (once per second), the connection to the hearing instruments is established. ConnexxAir is ready for programming the hearing instruments.
Programming with ConnexxAir When programming the hearing instruments while your patient is wearing them, you have to ensure that ConnexxAir is worn correctly. Refer to section "Wearing ConnexxAir" When programming hearing instruments that are lying on the table, certain distances must be considered. Refer to section "Programming on the table".
Wearing ConnexxAir In order to function correctly, your patient must wear the hearing instruments and ConnexxAir with the neckloop around the neck. The neckloop is also the antenna. X Unplug one neckloop plug and place the neckloop loosely around the patient's neck ➊. X Insert both neckloop plugs all the way ➋.
Programming on the table If you want to pre-configure the hearing instruments you can also have ConnexxAir and the hearing instruments lying on the table. When programming on the table: X Place the hearing instruments along the neckloop (refer to the picture). X Keep a minimum distance of 3 cm (1.2 inches) between the two hearing instruments. X Keep a distance of 5 to 10 cm (2 to 4 inches) between each hearing instrument and ConnexxAir.
Important safety information WARNING Risk of explosion! X Do not use your device in explosive atmospheres (e. g. in mining areas). WARNING Choking hazard! Your device contains small parts which can be swallowed. X Keep hearing instruments, batteries and accessories out of reach of children and mentally disabled persons. X If parts have been swallowed consult a physician or hospital immediately. NOTICE Your device is sensitive to extreme heat, high humidity, strong magnetic fields (> 0.
The performance of the wireless function may be affected by electromagnetic interference – e.g. from a computer monitor or fluorescent lamp system. X Move away from the source of interference if you experience difficulty. ### Note: Compatiblity with active implants must be verified. Otherwise, the following two warnings have to be deleted and we have to state that ConnexxAir is not compatible with active implants.
WARNING This device may interfere with measuring and electronic equipment. X Do not use your device on airplanes or areas where sensitive or life‑supporting electronic equipment is used. WARNING Risk of explosion when the rechargeable battery is handled wrong. X Do not short circuit, pierce, crush or disassemble the rechargeable battery. X Prior to return the battery for recycling, tape the electrodes to prevent short circuit, which may cause the battery to explode. X Do not place it in oven or fire.
In some countries restrictions for the usage of wireless equipment exist. X Refer to local authorities for further information. NOTICE Please make sure that the power plug is easily accessible to remove it from power supply if necessary. WARNING Risk of electrical shock! X Do not use obviously damaged devices and return them to point of sale. WARNING Note that any unauthorized changes to the product may cause damage to the product or cause injury. X Use only approved parts and accessories.
WARNING Risk of strangulation! X Ensure that the neckloop does not get entangled, e. g. in moving mechanical parts of machines. X Use only the delivered neckloop. It will automatically detach when entangled. X Do not use the device for children under the age of twelve.
Important information This device is intended to program hearing instruments wirelessly. Status LEDs The middle LED indicates the power status and the status of the wireless connection: Battery is low Charging Battery is fully charged (only when ConnexxAir is in charging cradle) Flashing slowly (once every 3 seconds) Programming connection is not established Data transfer between ConnexxAir and hearing instruments is not possible.
Troubleshooting Problem and possible solutions Connection to the hearing instruments cannot be established (middle LED is flashing slowly ) ■ Ensure that the hearing instruments are within operating distance and turned on. ■ Ensure that the neckloop is plugged in completely. ■ Ensure that the hearing instruments are compatible with ConnexxAir. Connection to the dongle cannot be established (all three LEDs are flashing green from left to right).
Maintenance and care NOTICE X Do not put your device in water! X Do not clean your device with alcohol or benzine. X Clean the device as necessary with a soft tissue. X Avoid abrasive cleaning liquids with additives such as citric acids, ammonia, etc. Replacing the battery The rechargeable battery is installed on delivery. If the battery deteriorates and it does not store charge as well as before, you can replace the battery. Spare batteries are available as service parts.
Firmware update The programming software informs you if a firmware update for ConnexxAir is available. To perform this update: X Use the supplied USB cable to connect ConnexxAir and the PC. X Follow the instructions on the screen. Explanation of symbols Symbols used in this document Points out a situation that could lead to serious, moderate, or minor injuries. Indicates possible property damage. Advice and tips on how to handle your device better.
Symbols on the device or packaging Do not dispose of the device with general domestic waste. Read more in section "Disposal information". Read and follow the instructions in the user guide.
Technical data of the power supply Golden Profit GPE006H-050100-Z Input voltage: 100-240 V AC Input current: 0.5 A Input frequency: 50-60 Hz Output voltage: 5 V DC Output current: 1A Disposal information X Recycle devices, accessories and packaging according to local regulations. X To avoid environmental pollution, do not throw batteries into household trash. X Recycle or dispose of batteries according to local regulations or return them to your Hearing Care Professional.
Wireless functionality USA FCC ID: ### Canada: ### Operating frequencies: fc = 3.28 MHz CE, FCC and Industry Canada compliance information can be found inside the battery compartment. ### FCC/IC IDs are missing. The ACMA compliance mark indicates conformity with the electromagnetic interference standards set by the Australian Communications and Media Authority (ACMA). Devices with the FCC marking comply with the standards of the FCC regarding electromagnetic interference.
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Legal Manufacturer Sivantos GmbH Henri-Dunant-Strasse 100 91058 Erlangen Germany Phone +49 9131 308 0 Document No. #####-99T##-#### ## Order/Item No. ### ### ## Master Rev##, ##.2016 © Sivantos GmbH, ##.2016 #### www.sivantos.