Quick start guide

Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • [e-mail] DocID: 490446, 490447_22.07.2020
EN
User manual
This manual contains important information on the safe operation of the product.
Read and follow the safety advice and instructions given. Retain the manual for future
reference. If you pass the product on to others please include this manual.
Stereo Link 5.8TX|RX
For the transport and protective packaging, environmentally friendly materials
have been chosen that can be supplied to normal recycling. Ensure that plastic
bags, packaging, etc. are properly disposed of. Do not just dispose of these ma-
terials with your normal household waste, but make sure that they are collected
for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equip-
ment Directive (WEEE) in its currently valid version. Do not dispose of your old
device with your normal household waste. Dispose of this product through an
approved waste disposal rm or through your local waste facility. Comply with
the rules and regulations that apply in your country. If in doubt, consult your lo-
cal waste disposal facility.
Safety instructions
Intended use
This product is meant to be used for the wireless transmission of line level audio
signals. Any other use or use under other operating conditions is considered to be
improper and may result in personal injury or property damage. No liability will be
assumed for damages resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are
not within reach of babies and young children. Choking hazard! Ensure
that children do not detach any small parts from the product. They could
swallow the pieces and choke!
Where to use the product
Never use the product
• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
• at locations where the unit can become wet
General handling
• To prevent damage, never use force when handling the product.
• Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use
liquid cleaners such as benzene, thinners or ammable cleaning agents.
Interference with other electrical devices
If the device is operated near radios or televisions, interference may occur. Then in-
crease the distance between the devices.
Features
• 5.8 GHz wireless stereo transmitter for radio transmission of a stereo audio signal
to the Stereo Link 5.8 RX receiver
• Maximum range 30 m
• A transmitter can be paired with up to 8 receivers
• Inputs / outputs: 2 × XLR or 2 × 1/4" jack (unbalanced)
• Switch for mono / stereo mode (transmitter)
• Volume control
• External power supply: 12V
1A (centre positive)
• Mounting bracket and power supply included
• Dimensions without antenna (W × H × D) 105 mm×45mm×115 mm
Operating elements
Using the product
1. Connect the devices to the power supply using the power supplies.
2. To pair the transmitter and receiver, press the PAIR buttons on both devices for
3 seconds. Then the status LEDs ash. After successful pairing, the LEDs light
up permanently. To pair up to 7 additional receivers, press the PAIR button on
the next receiver for 3 seconds. Then press the transmitter PAIR button for 3
seconds. If the status LEDs light up permanently, this receiver is also coupled to
the transmitter. Do the same with further receivers.
3. Connect the signal source to be transmitted to the balanced XLR input sockets
or the unbalanced jack sockets of the transmitter.
4. Use the STEREO / MONO switch to select the desired transmission type.
5. Adjust the input signal with the LEVEL control. Observe the SIGNAL LEDs that
indicate the input signal. Never connect signal sources to the XLR and jack inputs
at the same time.
6. Connect the devices to be supplied with the transmission signal to the balanced
XLR output sockets or the unbalanced jack sockets of the receiver.
7. Adjust the output signal (max. 2 V) with the LEVEL control of the receiver to the
input of the connected device.
Technical data
Transmitter and receiver frequency 5.8GHz
Latency <17ms
Transmit power 7dBm
Distance 30 meters (max. line of sight)
Sampling Rate 24bit, 48kHz
Line-in Level (recommended/max.) 500mV/2V
Line-out Level (recommended/max.) 500mV/2V
Frequency response 20Hz~22kHz
Signal-to-noise ratio >90dB
Impedance Transmitter: XLR (balanced): 10kΩ, 1/4" jack (unbalanced): 10kΩ
Receiver: XLR (balanced): 1kΩ, 1/4" jack (unbalanced): 1kΩ
     
DC INPUT
  
DC INPUT
1 PAIR button for pairing the devices
2 Status LED
3 MONO / STEREO switch
4 LEVEL control to adjust the input signal
5 SIGNAL LEDs indicate a input signal is present
6 Connection for external power supply
7 XLR (balanced) / 1/4" jack inputs (unbalanced)
1 PAIR button for pairing the devices
2 Status LED
3 LEVEL control for adjusting the output signal
4 SIGNAL LEDs indicate an input signal is received
5 Connection for external power supply
6 XLR- (balanced) / 1/4" jack outputs (unbalanced)
Transmitter
Receiver