English Skyfi2 install guide:SKYFi2 install guide layout 9/21/2006 12:09 PM Page 2 SKYFi2™ Installation Guide H o m e a n d Ve h i c l e K i t s Contents: SKYFi2 Vehicle Adapter Kit Setup . . . . . . . . . . . . 2 SKYFi2 Installation . . . . . . . . . . . . . . . . . . . . . . . . 7 XM Antenna Setup . . . . . . . . . . . . . . . . . . . . . . . . 12 SKYFi2 Home Adapter Kit Setup. . . . . . . . . . . . . 14 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
English Skyfi2 install guide:SKYFi2 install guide layout 2 Important: See page 19 for important FCC information. 9/21/2006 12:09 PM Page 3 SKYFi2 Vehicle Adapter Kit (SA10102) Setup Your Delphi XM® SKYFi2™ Vehicle Adapter Kit contains the following components: SKYFi2 Cradle Cassette audio adapter Swivel and Vent Mounts Nokia® style button mount converter Figure 1. SKYFi2 Vehicle Adapter Kit components.
English Skyfi2 install guide:SKYFi2 install guide layout 9/21/2006 12:09 PM Hooking up Your SKYFi2 Receiver Cradle Caution: Connect only appropriate input devices to the SKYFi2 Vehicle Adapter Kit. Connecting any incorrect input devices may damage the system and/ or the external electronic device. It is recommended that you use only the 12V to 6V conversion power adapter that came with your SKYFi2 Vehicle Adapter Kit.
English Skyfi2 install guide:SKYFi2 install guide layout 4 After connecting the power and antenna jacks into the car cradle, the included organizer can be used to improve the appearance of the installation. See figure 3. The cable twist ties that were provided with the power adapter and car antenna cables can be reused to gather, bundle, twist tie, and secure any excess cable. Excess cable can be gathered under the dash, between the seat or console, or under the mat so it is not in the way.
English Skyfi2 install guide:SKYFi2 install guide layout 9/21/2006 12:09 PM Page 6 The SKYFi2 Vehicle Adapter Kit offers you many ways of connecting your SKYFi2 to your vehicle’s radio. All options provide excellent sound quality and stereo separation. Review and consider your own unique situation when choosing from the three options.
English Skyfi2 install guide:SKYFi2 install guide layout 6 Cassette Adapter For vehicles with a built-in cassette player. Due to its superior audio quality, this configuration is recommended over the professionally wired or self install XM SureConnect configurations if a cassette slot is available in the vehicle. 9/21/2006 12:09 PM Professional Wired FM A wired FM installation kit is available from your retailer for professional installation. See your retailer for details.
English Skyfi2 install guide:SKYFi2 install guide layout SKYFi2 Installation Because every vehicle is different, these instructions are provided as a general guideline only. If you need help, consult a professional installer. 1. Decide which method (cassette adapter, professional wired FM, or self install (XM SureConnect) is most appropriate for your vehicle and where you live. 2. Verify the system is working by completing a test.
English Skyfi2 install guide:SKYFi2 install guide layout 8 3. Turn off the radio and SKYFi2 Receiver. Disconnect all cables. 4. Find a place where you can mount your SKYFi2 vehicle cradle where it is most convenient for you to use. It should be mounted to a hard, flat surface below the top of the dash within easy reach. 9/21/2006 12:09 PM 5. The SKYFi2 Vehicle Adapter Kit has three mounting options: flat mount, vent mount or swivel mount. a.
English Skyfi2 install guide:SKYFi2 install guide layout c. Swivel mount:This mount allows you to adjust the angle of your SKYFi2 Vehicle Adapter after it is installed. This mount uses a strong adhesive that is not easily repositioned when installed, so use care when choosing the location of and placing the mount. Do not install this mount on a leather surface. Install the mount only if the temperature is at least 60°F. – Clean the mounting surface with the enclosed surface preparation cleaning kit.
English Skyfi2 install guide:SKYFi2 install guide layout 9/21/2006 12:09 PM Page 11 6. Clip the SKYFi2 vehicle cradle onto the swivel mount (figure 4). 7. Reassemble the system as in step 2. 8. Attach the antenna as explained on page 12 and route the antenna cable as described on page 13. 10 To vehicle dashboard Figure 3. Installing the vent mount to your vehicle’s air vent. Figure 4. Attach vehicle mount to back of SKYFi2 as shown.
English Skyfi2 install guide:SKYFi2 install guide layout Removing swivel mount from your dashboard You can remove the swivel mount from your dashboard by following these steps: 1. Lift one edge of the adhesive pad gently with fingers or the rounded edge of a spoon. Once enough of the edge is loosened to grip with your fingers, pull the pad gently from the mounting surface at a 90-degree angle. Do not use sharp tools that could damage the vehicle’s interior. 9/21/2006 12:09 PM 2.
English Skyfi2 install guide:SKYFi2 install guide layout 12 XM Antenna Setup For best reception, the XM Antenna should be placed either: – In front of the rear window (option1) – Behind the windshield (option 2) When deciding which location to choose, keep in mind: – The antenna will perform best if it has an unobstructed view of the open sky. – If the vehicle has roof racks or skid ribs, the antenna can be mounted off-center.
English Skyfi2 install guide:SKYFi2 install guide layout 9/21/2006 12:09 PM Routing the Cable Page 14 Option 2 When using option 2, route the cable along the door jamb and into the vehicle as shown in figure 6. Route the cable across the weather seal near the bottom of the door to reduce water leaks. Option 1 When using option 1, route the cable into the trunk as shown in figure 6. Always cross the weather seal at the lowest part of the trunk to reduce water leaks.
English Skyfi2 install guide:SKYFi2 install guide layout 14 9/21/2006 12:09 PM SKYFi2 Home Adapter Kit (SA10103) Setup Your Delphi XM SKYFi2 Home Adapter Kit contains the following components: Page 15 Hooking up Your SKYFi2 Receiver Home Stand Note: See SKYFi2 User Guide for important user information. SKYFi2 Home Stand 6V AC power adapter XM High gain Indoor/Outdoor Home Antenna with 25 ft. cable Audio cable Figure 7. SKYFi2 Home Adapter Kit components.
English Skyfi2 install guide:SKYFi2 install guide layout 9/21/2006 12:09 PM Page 16 Installation instructions: 1. Turn off both your SKYFi2 Receiver and home stereo. 2. Connect cables as illustrated in figure 8. 3. Position the XM Antenna so that it is facing south. Ideally, it should point through a window. 4. Turn on your SKYFi2 Receiver and the stereo.Tune to XM channel 1.You should be able to hear the XM Preview channel. If not, check all connections.
English Skyfi2 install guide:SKYFi2 install guide layout 16 Aiming the XM Home Antenna For best reception, aim the home antenna by following these instructions: 1. Press the “menu” button on the SKYFi2 Receiver. 2. Use the scroll wheel to select the “Antenna Aiming” option. Press the “XM” button to confirm selection. 3. This display will remain on until you press the “menu” button again, so you have plenty of time to aim the antenna. Slowly turn and tilt the antenna.
English Skyfi2 install guide:SKYFi2 install guide layout Delphi Limited Consumer Warranty Delphi Product and Service Solutions (“Delphi”) warrants all Portable XM Satellite Radio Accessory Products sold by Delphi (each “Product”) to be free of defects in material and workmanship, subject to the following conditions: The duration of Delphi’s warranty with respect to each product is limited to one (1) year from the date of sale to the original consumer purchaser.
English Skyfi2 install guide:SKYFi2 install guide layout 18 How you (the Customer) can get service: To obtain warranty service, you must return the defective Product with the original receipt to the original place of purchase. If further clarification or additional information is required from Delphi, you may call Delphi at: 1.877.GO DELPHI (1.877.463.3574).
English Skyfi2 install guide:SKYFi2 install guide layout 9/21/2006 12:09 PM FCC Statement Please note that the power cable that has been supplied with your device is supplied with a permanently attached ferrite bead. It is the responsibility of the user to use the cable with the ferrite bead. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
English Skyfi2 install guide:SKYFi2 install guide layout 9/21/2006 12:09 PM Page 1 Delphi Corporation 1441 West Long Lake Road Troy, Michigan 48098-5090 U.S.A. Customer Service: [1] 877.GO DELPHI www.delphi.com Printed on Recycled Paper ©2006 Delphi Corporation. All rights reserved. DPSS-06-E-061 The SKYFi2 name, XM name, and related logos are trademarks of XM Satellite Radio Inc. All other trademarks are the property of their respective owners.