Manual

ManualsBrandsSioux Tools ManualsPower Tools1DA

Form ZCE743

Date 2006October4/C

Page 1 of 10

Printed In U.S.A.

INSTRUCTIONS & PARTS LIST FOR “1DA” SERIES RIGHT ANGLE DIE GRINDERS

SERIAL “A”

AIR SUPPLY

The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure

regulator, and lubricator will insure maximum output and life of tools. Before connecting tool, blow out the air line to remove

water and dirt which may have accumulated.

HOSE AND HOSE CONNECTIONS

Supply hose should be not less than 1/4" (6.35 mm) I.D. Extension hoses should be at least 3/8" (10 mm) I.D. Use couplings

and fittings with at least 1/4" (6.35 mm) I.D.

LUBRICATION

• Use SIOUX No. 288 air motor oil. An airline lubricator, set to deliver 1 to 2 drops per minute, is recommended. If a lubricator

is not used, add .06 oz. (1.8 cc, 18 to 25 drops) of oil into the air inlet every 2 to 3 hours.

• Lubricate the angle head every 6-8 working hours with Sioux 1232A grease.

GENERAL OPERATION

• Speed of the tool may be adjusted by turning the speed control, located at the back of the tool, opposite the valve.

• When using the tool in a vise or toolpost holder, use moderate pressure.

• Refer to “Safety Guide for Sioux Abrasive Wheel” for abrasive wheel selection and safe operation.

• Angle head position can be rotated 360°. Be sure to keep the angle head retainer tight to prevent the angle head from

turning.

• When installing the backing pad, be sure to leave some clearance between the end of the shroud adapter and the backing

pad so they will not rub.

Read and understand "Safety Instructions For Air Tools" and these instructions before operating

this tool.

SAVE THESE INSTRUCTIONS!

*Sound Pressure *Sound Power *Vibration

Catalog No. dBA dBA m/s

1DA221HP 82.16 93.01 2.84

1DA321HP 82.16 93.01 2.84

*per PN8NTC1 *per PN8NTC1 *per ISO 8662

SOUND AND VIBRATION READINGS

DECLARATION OF CONFORMITY

We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products

1DA221HP, 1DA321HP

to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:

EN 792, EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1

following the provisions of

89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.

February 1, 2005

Murphy, North Carolina, USA

Date and place of issues

Mark S. Pezzoni

President

Power and Specialty Tools

Name and position of issuer

Signature of issuer

Summary of content (10 pages)

PAGE 1
Form ZCE743 Date 2006October4/C Page 1 of 10 INSTRUCTIONS & PARTS LIST FOR “1DA” SERIES RIGHT ANGLE DIE GRINDERS SERIAL “A” Read and understand "Safety Instructions For Air Tools" and these instructions before operating this tool. SAVE THESE INSTRUCTIONS! AIR SUPPLY The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator, and lubricator will insure maximum output and life of tools.
PAGE 2
ANWEISUNGEN & TEILELISTE FÜR RECHTWINKLIGE SCHNEIDEISENSCHLEIFMASCHINEN DER “1DA”-SERIE SERIE “A” Vor dem Betrieb dieses Werkzeugs lesen Sie bitte diese Anweisungen und die “Sicherheitsanweisungen für Druckluftwerkzeuge”. BEWAHREN SIE DIESE HINWEISE AUF! DRUCKLUFTZUFUHR Die Werkzeugleistung hängt von der ordnungsgemäßen Zufuhr von sauberer, trockener Luft mit einem Druck von 6,2 bar (90 psig) ab.
PAGE 3
INSTRUCCIONES Y LISTA DE PARTES PARA LAS RECTIFICADORAS DE MATRIZ EN ÁNGULO RECTO DE LA SERIE “1DA” SERIE “A” Lea y entienda “Instrucciones de seguridad para herramientas neumáticas” y estas instrucciones antes de operar esta herramienta. ¡GUARDE ESTAS INSTRUCCIONES! SUMINISTRO DE AIRE La eficiencia de la herramienta depende de un suministro adecuado de aire seco 90 psig (6,2 bar).
PAGE 4
ISTRUZIONI E LISTINO PARTI PER MOLATRICI/LEVIGATRICI ANGOLARI SERIE “1DA” SERIE “A” Leggere attentamente le “Istruzioni per la sicurezza degli attrezzi ad aria compressa” e le seguenti istruzioni prima di utilizzare la presente apparecchiatura. CONSERVARE QUESTE ISTRUZIONI! ALIMENTAZIONE ARIA L’efficienza dell’apparecchio dipende da un’adeguata alimentazione di aria pulita ad una pressione di 90 psi (6,2 bar).
PAGE 5
INSTRUCTIONS ET LISTE DE PIÈCES DÉTACHÉES POUR MEULEUSES D’OUTILLAGE À RENVOI D’ANGLE DROIT DE SÉRIE “1DA” SÉRIE “A” Lisez avec attention les “Consignes de sécurité des outils pneumatiques” avant de vous en servir. CONSERVER CES INSTRUCTIONS ! ALIMENTATION EN AIR L’efficacité de l’outil dépend de la qualité de l’air d’alimentation, qui doit être sec et propre, et de la pression, qui doit être de 6,2 bar (90 psi).
PAGE 6
INSTRUCTIES & ONDERDELENLIJST VOOR HAAKSE SLIJPMACHINES (SERIE “1DA”) SERIENUMMER “A” Voordat u de machine in werking stelt, moet u deze instructies en de “Veiligheidsvoorschriften voor persluchtmachines” gelezen en begrepen hebben. BEWAAR DEZE INSTRUCTIES! PERSLUCHTTOEVOER Het gebruik van droge perslucht met de geschikte druk (90 psig / 6,2 bar) is bepalend voor een goed rendement van de machine.
PAGE 7
ANVISNINGAR OCH RESERVDELSLISTA FÖR ”1DA-SERIEN” HÖGERVINKLADE TURBINSLIPAR SERIE “A” Läs och sätt dig in i ”Säkerhetsföreskrifter för tryckluftsverktyg” samt dessa anvisningar innan du använder detta verktyg. SPARA DESSA FÖRESKRIFTER! LUFTTILLFÖRSEL Hur effektivt verktyget fungerar beror på korrekt tillförsel av ren torr luft vid 6,2 bar (90 psig). Använd ett ledningsfilter, en tryckregulator och en smörjapparat för att få maximal effekt och livslängd på verktygen.
PAGE 8
PARTS LIST FOR “1DA” SERIES RIGHT ANGLE DIE GRINDERS SERIAL “A” 8
PAGE 9
PARTS LIST FOR “1DA” SERIES RIGHT ANGLE DIE GRINDERS SERIAL “A” Fig. No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 33. 32. 34. 35. Part No.
PAGE 10
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Der durch Elektrosanden, -sägen, -schleifen und -bohren sowie durch andere Bauarbeiten anfallende Staub enthält Chemikalien, die nachweislich Krebs sowie Geburts- bzw. andere Fortpflanzungsschäden hervorrufen.