KODAK PIXPRO 4KVR360 User Manual
Before You Start Declaration of Conformity Responsible Party: JK Imaging Ltd. Address: JK Imaging Ltd., 17239 So. Main Street, Gardena, CA 90248 USA JK Imaging Europe, 71 Clarendon Road, Watford, WD17 1DS, UK Company Website: http://kodakpixpro.com About this Manual Thank you for purchasing this product. Please read this manual carefully and keep it in a safe place for future reference. JK Imaging Ltd. reserves all rights of this document.
For Customers in the U.S.A. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
For Customers in Europe This symbol [crossed-out wheel bin WEEE Annex IV] indicates separate collection of electrical waste and electronic equipment in the European countries. Please do not throw the equipment into domestic refuse. Please use the return and collection systems available in your country for proper, safe disposal of this product. “CE” mark indicates that this product complies with the European requirements for safety, health, environment and customer protection.
For SAR statement A minimum separation distance of 0 XX cm cm must must bebe maintained maintained between between the the user’s user’s body body and and the the device, device, including including the the antenna antenna during during bodybodyworn operation to comply with the RF exposure requirements in Europe. To compliance with RF Exposure requirements in Europe, third-party belt-clips, holsters or similar accessories used by this device should not contain any metallic components.
Safety Notes Product Notes: Ù %P OPU EJTBTTFNCMF PS BUUFNQU UP SFQBJS UIF QSPEVDU CZ ZPVSTFMG Ù %P IBOEMF UIF QSPEVDU QSPQFSMZ 5IJT QSPEVDU NBZ CF EBNBHFE JG ESPQQFE QVODUVSFE PS DSVTIFE Ù "WPJE EJSFDUMZ UPVDIJOH UIF MFOT FMFNFOU QMFBTF VTF QSPGFTTJPOBM MFOT DMFBOJOH QBQFS UPHFUIFS XJUI MFOT DMFBOJOH BHFOUT UP XJQF UIF MFOT BOE LFFQ UIF MFOT clean.
Memory Card Notes: Ù 5IF NFNPSZ DBSE SFGFSSFE UP JO UIJT NBOVBM JT B microSD card, microSDHC card or microSDXC card. Ù 1MFBTF LFFQ UIF NFNPSZ DBSE DMFBO BOE ESZ Ù 8IFO JOTFSUJOH B NFNPSZ DBSE NBLF TVSF UIF OPUDI EJSFDUJPO PG UIF DBSE NBUDIFT UIF OPUDI EJSFDUJPO PG UIF NFNPSZ DBSE NBSL OFBS UIF DBSE TMPU %P OPU force the memory card into the card slot.
Contents Before You Start .................................................................................................................................... 1 Safety Notes ........................................................................................................................................ 5 Contents .............................................................................................................................................. 7 Getting Ready ...............................
Every Shooting Mode Settings ( General Settings / / / ) .....................................................................21 ............................................................................................................................... 27 Remote Control-D ...............................................................................................................................................30 Using Interfacing .................................................................
Getting Ready Accessories Included Your product box should contain the product you purchased along with the following accessories. If anything is missing or appears to be damaged, please contact your retailer. (The AC Adapter style will vary according to the power requirement from different countries or regions.
Part Names 1 Buzzer 2 Wi-Fi indicator 8 9 Wi-Fi button / Direction button (lower) / Remote 3 control pairing (press and hold) 7 10 6 11 12 13 5 4 3 2 14 4 Lens B (235 Degree) 5 Lens status indicator B 6 Power button 7 Status indicator 8 LCD 9 Bluetooth mark 10 Microphone 15 11 1 Video recording button / Shooting button / OK button 16 17 18 19 20 12 Lens A (155 Degree) 13 Lens status indicator A 14 Menu button / Direction button (upper) / Mode switching (press and hold)
Mounting / Removing Lens Ring and Lens Cover The processes of mounting/removing lens ring and lens cover are the same, with lens cover as an example as below: Removing lens cover: Mounting lens cover Turn the lens cover according to the illustrated direction until it separates from the 4KVR360. Turn and firmly tighten the lens cover according to the illustrated direction. The lens cover protects the lens from being damaged (dustproof, shockproof and splash proof).
Installing Battery 1. Open the battery cover First, set the battery cover lock to the left ʒ , and then push the open switch of the battery cover downward ʓ . 2. Insert the battery Insert the battery into the battery compartment along the direction of arrow ʔ (note the location of the + and - symbols). 3 3. Close the battery cover 4 Close the battery cover the rear cover will “click” when tightly closed ʕ . Finally, move the battery cover lock to the right ʖ .
Installing Memory Card Open the battery cover, then insert the memory card into the card slot (note the direction of the memory card gap), push the bottom end of the memory card with a fingertip into the slot completely, and then close the side cover. A memory card (microSD / microSDHC / microSDXC) is optional and is not included in the product package. It needs to be purchased separately. Please use an original memory card, which is Class 10 or higher and has a capacity of 8GB to 256GB.
Charging the Battery Please use the battery charger or AC adapter to charge the battery in an ambient temperature ranging from 10 ˚C to 35 ˚C. Charging the battery with a battery charger: 1. Place the battery into the battery charger according to the direction illustrated. Use the Micro USB cable to connect the battery charger and the AC adapter, and then plug the AC adapter into an electrical outlet. 2. The indicator light will turn red while charging.
Charging the camera with a computer: 1. Place the battery into the camera. 2. Use the Micro USB cable to connect the camera (off) to a computer (on). 3. The indicator light will become orange while it is charging. The indicator will go out once charging is finished. The camera cannot be recharged when power is on. 6TJOH UIF *OUFSOBM .
Configuration and Operation Main Interface Introduction The Main Interface 2 3 1. Mode 4 Movie mode Snap Shot Photo mode High-speed movie mode 1 5 11 6 Burst mode Memory card 2. 3. Movie size: 10 9 7 8 VR / Front / Round / Hi Speed / / / / / 4. Battery status 5. Display mode VR / Round / Front 6. Remaining recording time: mm:ss / hh:mm / none 7. Motion detection (on) 8.
Power On / Off Power on: When the power is off, press the button for more than one second to turn on the product. Power off: When the power is on, press the button for more than one second to turn off the product. If the product cannot be powered off normally, you can remove the battery from the camera to force it to power off. Start-up for language, date and time 1. Press the button to turn on the product.
Modes Introduction In the main interface, press and hold the button to enter the mode selection interface. Press the or button to select any one mode; press the button to the main interface of the current mode. 4 modes are available: Movie mode , Snap shot photo mode , High-speed movie mode , Burst mode . Movie mode Enable video recording. It is suitable for recording in most conditions. Operation method: Press the button to start recording. Press the button again to stop recording.
Snap Shot Photo mode Enables photo shooting. It is suitable for recording in most conditions. Operation method: Press the button for photo. High-speed movie mode The product shoots ultra-high speed movies, and plays back with normal 30fps speed. Operation method: Press the button to start recording. Press the button again to stop recording. Sound cannot be recorded in this mode. Burst mode Enables ten photos to be captured continuously before auto pause.
Introducing the Menu 1. In the main interface, press and hold the ), General Settings / button to enter the sub-menu interface. There are 2 options: Every Shooting Mode Settings ( . Press the or button to select the item, and press the / / button to enter the corresponding advanced setting interface. The sub-menu interface 2.
Every Shooting Mode Settings ( / / / ) The advanced Setting in every shooting mode Movie Settings Photo Settings High-speed Movie Settings Burst Settings The sub-menu interface The advanced Setting interface 21
Take the recording setting menu as an example; the setting operating manners of other shooting modes are the same as that of the recording setting menu. Ultra Middle -3.0、-2.7、-2.3、-2.0、-1.7、-1.3、-1.0、-0.7、-0.3、+0.0、+0.3、+0.7、+1.0、+1.3、+1.7、+2.0、+2.3、+2.7、+3.
Display mode Set image storage form.
Movie size Set video resolution. Front Mode (16:9) VR Mode (2:1) Ù 3840×1920 (24fps) Ù 3840×2160 (30fps) Ù 3840×1920 (15fps) Ù 1920×1080 (60fps) Ù 1920×960 (30fps) Ù 1920×1080 (60fps) Ù 1280×640 (120fps) Ù 1920×1080 (60fps) Ù 1280×720 (60fps) Ù 1280×720 (120fps) Round Mode (1:1) Ù 2880×2880 (24fps) Ù 1920×1920 (30fps) The selectable options are different for different modes, please be subject to actual operations.
Self Timer Setting a self-timer function. There are 3 options: Ù 4FMG 5JNFS 0ū Ù 4FMG 5JNFS TFD Ù Self Timer -10sec EIS Set electronic image stabilization (EIS) function. There are 2 options: Ù &OBCMF Ù Off Motion detection Motion detection means that if the product detects moving objects entering into the view, it will automatically start recording.
Color Set image color. There are 3 options: Ù /PSNBM Ù #MBDL BOE XIJUF Ù Vivid White balance White balance means that the user adjusts the color temperature under different light sources to ensure that the colors are reproduced correctly. There are 6 options: Ù Auto white balance Ù %BZMJHIU Ù $MPVEZ Ù 'MVPSFTDFOU Ù *ODBOEFTDFOU Ù Underwater Exposure Compensation Set up to adjust the picture brightness.
General Settings XXX Sub-menu Advanced setting Selectable items 27
Sound Set the sound of the product. There are 4 options: Ù 4PVOE@0ū Ù 4PVOE Ù 4PVOE Ù Sound_On Power off When this function is enabled, if there are no actions taken within a set time frame (except while recording or connected to Wi-Fi), the product will automatically shut down. There are 2 options: Ù NJOVUFT Ù Off USB connection mode The mode of connecting the Micro USB wire to the computer is set.
Format Format can clear all data stored in the memory card. There are 2 options: Ù $POȗJSN Ù If select , press the Cancel button to start formatting, and return to the advanced Setting interface after finishing. Reset settings Reset settings can recover all product settings to the factory defaults (except for date and time).
Remote Control-D Remote Control Appearance Specifications Model: RR-BK04 1 2 3 1. Bluetooth signal test button 2. Connect and shooting status indicator lamp 3. Recording / Shooting button Dimension:30×20×13.7mm Weight: 27±2g (including battery) Dust proof: IP6X Temperature: -10 to 40°C Humidity: 0~90% Battery: button cell CR2032 Before using: Pull out the insulating strip completely prior to operating the remote control.
Installing the Battery: Use a screwdriver to remove the screw by turning it counterclockwise (Fig. 1), open the battery cover and insert the batteries (Fig. 2), and close the battery cover and rotate the screw in the opposite direction. Negative Screw Battery cover Install the mini remote control and tripod: 1. Press the mini mount onto the tripod (Fig. 1). And then close the tripod (Fig. 2). Align the mount anchor point to the tripod anchor point. 2.
How to pair: 1. Pair the camera and remote control Method of one remote control for one camera: With the camera turned on, press the Press and hold the and button for 2 seconds to enter the pairing mode. buttons on the remote control simultaneously until pairing is successful.
While pairing, the remote control shall be closer to the camera. 2. Press the button on the remote control to start shooting or recording, and press the button again to stop recording. Other parameters are set the same as the current settings of the camera at the same mode. 3. To terminate remote control, press the button.
In case of successful pairing between the camera and the remote control: 1. If the camera is powered off, the camera is powered on and start recording by pressing the button on the remote control. 2. The camera is powered on or whether the remote control is paired successfully is tested by pressing the pressing and holding the button. The camera will be powered off by button (more than 1.5 seconds). 3.
Remote Control-C (Optional) A remote control can be used for remotely controlling the camera at a long distance. 7KH UHPRWH FRQWURO LV RSWLRQDO ,I \RX QHHG RQH FRQWDFW WKH ORFDO UHWDLOHU WR EX\ RU DFFHVV KWWS NRGDNSL[SUR FRP for details of customer service.
How to pair: 1. Pair the camera and remote control Method of one remote control for one camera: In the camera boot state, press the button for 2 seconds to enter the pairing mode. Positive Negative Press and hold the and buttons on the remote control simultaneously until pairing is successful.
:KLOH SDLULQJ WKH UHPRWH FRQWURO VKDOO EH FORVHU WR WKH FDPHUD 2. Set the desired shooting mode (movie mode RU VQDS VKRW SKRWR PRGH DQG WKH GLVSOD\ PRGH 95 5RXQG )URQW ). 2WKHU SDUDPHWHUV DUH VHW WKH VDPH DV WKH FXUUHQW VHWWLQJV RI WKH FDPHUD DW WKH VDPH PRGH 3.. Press the EXWWRQ RQ WKH UHPRWH FRQWURO WR VWDUW VKRRWLQJ RU UHFRUGLQJ DQG SUHVV WKH 4. To terminate remote control, press EXWWRQ DJDLQ WR VWRS UHFRUGLQJ the button.
In case of successful pairing between the camera and the remote control (the camera is capable of memorizing the remote control paired successfully last time): ,I WKH FDPHUD LV SRZHUHG RII WKH FDPHUD LV SRZHUHG RQ DQG VWDUW UHFRUGLQJ E\ SUHVVLQJ WKH button on the remote control. 7KH FDPHUD LV SRZHUHG RQ RU ZKHWKHU WKH UHPRWH FRQWURO LV SDLUHG VXFFHVVIXOO\ LV WHVWHG E\ SUHVVLQJ WKH holding the 3. When the EXWWRQ 7KH FDPHUD ZLOO EH SRZHUHG RII E\ SUHVVLQJ DQG button (more than 1.5 seconds).
Using Interfacing Micro USB interface Charging 14 Using an external power supply In case of low battery power, or when a long-term power supply is needed, an external power supply (AC adapter, vehicle power supply, portable power supply or other power unit) can be used instead of a battery. At this time, the setting of functions, photography, and other operations can be performed. When powered on, use the Micro USB cable to connect the camera to an external power supply.
The folder structure of a microSD card on which this unit has performed recording is as follows. Example folder structure of a microSD card: Folder numbers range from 100 to 999. Four or eight alphabetic characters after a three-digit number indicate the file type. 4KVR360 A. Still pictures in JPEG format (Each folder stores a maximum of 999 still pictures) ͓ Folder numbers range from 100 to 999. Four alphabetic characters indicate the camera lens type.
Webcam Connect the camera and computer via a Micro USB cable and use the camera as a Webcam. 1. Download the drivers for the app “PIXPRO 4KVR360 67$Õ GSPN UIF PȘJDJBM XFCTJUF BOE JOTUBMM JU POUP UIF DPNQVUFS BT QSPNQUFE PO UIF TDSFFO Americas Europe http://kodakpixpro.com/Americas/ support/downloads.php 2. Set the USB connection method as http://kodakpixpro.com/Europe/ support/downloads.php from the camera menu. 3. Connect the computer (turned on) and camera (turned on) via a Micro USB cable.
5. Change the desired settings and click on “OK” to exit. The image size can be adjusted on your computer. If you choose a resolution of 1280×720, the image will be displayed at an aspect ratio of 16:9. This function supports Windows 7 and higher OS. (Graphics GPU must support Direct3D 10.) Applicable video software: Skype™. The Webcam consumes battery power, so we recommend you use fully recharged batteries. (In case of fully recharged batteries and HD image quality, it may work about 6 hours.
Micro HDMI interface The television (on) up to the HDMI standard and the camera (on) are connected by use of a Micro HDMI wire (bought independently). After the connection succeeds, the documents in the memory cards of the camera are displayed on the television, while or Liveview is displayed on the camera. The shooting and playback functions can be realized by use of the camera: 1. Press the button to switch between the video playback mode, the photo playback mode and the shooting mode. 2.
The playback function can be realized by use of the television remote control: 1. Press the left and right keys to switch the documents. 2. Press to return to shooting screen. 3. Press to hide or display the screen information. 4. For browsing the video document, press the central key to start playing, press the left key to fast reverse, press the right key to fast forward, and press the central key again to pause playing. 5. Press to delete the current document and select 6. Press to stop playing.
Wi-Fi Mode Download and Install App ƔSmart Device: Download the App installation package (App name: PIXPRO VR360) to your smart device from the path below, and install it by following the instructions on the interface. For Android devices, search and download the App "PIXPRO VR360" in Google play, and install it by following the instructions on the interface. For iOS devices, search and download the App "PIXPRO VR360" in App Store, and install it by following the instructions on the interface.
Connect camera to smart device (or PC) with Wi-Fi. Operation method: 1. Camera: Check SSID (Service Set Identifier) (PIXPRO-4KVR360_KXXX) and password (initial password: 12345678) indicated on the label in the battery compartment of the camera. With the camera turned on, press the 2. Smart Device or PC: Enable Wi-Fi mode, it will automatically search the nearby Wi-Fi hotspots. Select the one with the same SSID (PIXPRO-4KVR360_KXXX) and input the password.
If the Wi-Fi connection is cut off while recording, the camera will continue to record and enter the connectionless recording interface. When displays in the interface, press the button, and press the or button to select , and then press the button to exit the Wi-Fi connection.
Connect camera to smart device with NFC 1. Enable NFC mode on your smart device. 2. Use your smart device to lightly touch the NFC mark on the camera. If the smart device has a prompt tone or vibration, it means the connection is successful. 3. The App will open automatically on your smart device. The NFC feature will only be available when your smart device's screen is unlocked.
Appendices Specifications Design and specifications are subject to change without notice. Image Sensor A Lens A Type 1/2.3" BIS CMOS Effective Pixels 20.68 Megapixels Total Pixels 21.14 Megapixels Focal Length 1.633mm Equivalent to 35mm film 9.18mm F Number F2.4 Lens Construction 7 groups 8 elements Focus Fix Focus Max. 197 Degree [For Front Mode (16:9) ] Field of View Image Sensor B Lens B Anti-Handshake Max. 155 Degree [For VR Mode (2:1) ] Focusing Range 30cm~f Type 1/2.
27MP: 7360x3680 (2:1) 15MP: 5520x2760 (2:1) 27MP: 7360x3680 (2:1) Still Image 15MP: 5520x2760 (2:1) 13MP: 3680x3680 (1:1) Stitched VR Mode Global Round Mode 8MP: 3840x2160 (16:9) 9MP: 3525x2644 (4:3) Front Mode (2:1) 3840×1920/24fps Global VR Mode 3840×1920/15fps Number of Recording Pixels 1920×960/30fps Stitched (1:1) 2880x2880/24fps Round Mode Movie 1920×1920/30fps (16:9) 3840x2160/30fps 1920x1080/60fps Front Mode 1280x720/60fps High-speed Movie : Still Image File Format Movie 1280×640/120
Freeze-proofing -10°C LCD 1.0 inch TN LCD (With Backlight) Level Gauge 3-axis ISO Sensitivity Auto (100~1600) (Photo) Exposure Metering Method Artificial Intelligence AE (AiAE) Exposure Control Method Program AE Burst Supported White balance Auto white balance, Daylight, Cloudy, Fluorescent, Incandescent, Underwater Auto (100~800) (Movie) Internal Memory: No Recording Media microSD / microSDHC / microSDXC Card (Up to 256GB Support) Language English Interface USB 2.
Prompts and Warning Messages Message Description Processing mode There are too many files, which may cause a delay to power on. When pressing the button for shooting, the memory card cannot be accessed because there are too many folders. No memory card is detected in the camera. When turning on the product or pressing the memory card is out of capacity. After copying the files to the computer, choose to delete or format. Insert the memory card.
Message Description Processing mode The camera is set as "Mass Storage", connecting to the computer USB. User should do nothing. The camera is set as "Web Cam", connecting to the computer USB. User should do nothing. Connecting to the HDMI device. User should do nothing. A warning for low battery before shutting down automatically. 5IF ȗJSNXBSF DBOOPU CF VQEBUFE XIFO QPXFS JT JOTVȘJDJFOU Charge or replace with a new battery. Updating firmware. User should do nothing.
Trouble Shooting Problem Product does not turn on Possible causes The battery has been depleted. Solution Charge the battery. The battery is installed incorrectly. Please follow the charging instructions in the manual to install the battery. There is dirt on the lens or the lens cover. Clean with a clean, lint-free dry cloth. Failed to connect Wi-Fi Wrong password entered. Please re-enter the password.
The Kodak trademark, logo and trade dress are used under license from Kodak. © 2017 JK Imaging Ltd. All Rights Reserved. JK Imaging Ltd., 17239 So. Main Street, Gardena, CA 90248 USA JK Imaging Europe, 71 Clarendon Road, Watford, WD17 1DS, UK http://kodakpixpro.com Made in Myanmar Ver. 1 Ver.