SP360 4K Action Cam User Manual
Before You Start Declaration of Conformity Responsible Party: JK Imaging Ltd. Address: JK Imaging Ltd., 17239 South Main Street, Gardena, CA 90248, USA JK Imaging Europe, 71 Clarendon road, Watford, WD17 1DS, UK Company Website: www.kodakpixpro.com About this Manual Thank you for purchasing this product. Please read this manual carefully and keep it in a safe place for future reference. JK Imaging Ltd. reserves all rights of this document.
For Customers in the U.S.A. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
For Customers in Europe This symbol [crossed-out wheel bin WEEE Annex IV] indicates separate collection of electrical waste and electronic equipment in the European countries. Please do not throw the equipment into domestic refuse. Please use the return and collection systems available in your country for proper, safe disposal of this product. “CE” mark indicates that this product complies with the European requirements for safety, health, environment and customer protection.
- EN 301 489-17 V2.2.1:2012 ] > ]> ] for Broadband Data Transmission Systems 6 * * of Directive 1999/5/EC. 6 \ 6 > ] # # + Q * Packaging: Please follow local regulations for the recycling of packaging.
Safety Notes Product Notes: % 6 6 6 & &
Memory Card Notes: % + microSD card, microSDHC card or microSDXC card. < 6 memory card into the card slot.
Contents Before You Start ......................................................................................................................................1 Safety Notes ............................................................................................................................................5 Contents ..................................................................................................................................................7 Getting Ready.........................
High-speed movie mode Burst mode .................................................................................................................................................. 20 ........................................................................................................................................................................ 20 Introducing the Menu ....................................................................................................................................
Getting Ready Accessories Included Your product box should contain the product you purchased along with the following accessories. If anything is missing or appears to be damaged, please contact your retailer. (The AC Adapter style will vary according to the power requirement from different countries or regions.
Kodak PIXPRO SP360 4K View 1 2 1 10 9 8 7 Lens Video recording button / Shooting button / OK button 3 2 4 5 6 3 Microphone 4 Status indicator 5 Wi-Fi button 6 Wi-Fi indicator 7 NFC mark 8 Menu button / Direction button (lower) 11 9 Power button / Mode button / Direction button (upper) 12 10 LCD 11 Battery cover 12 Battery cover lock 13 14 Side cover 15 Location hole 16 Tripod socket 13 14 15 16 10
Mounting / Removing Lens Ring and Lens Cover The processes of mounting/removing lens ring and lens cover are the same, with lens cover as an example as below: Removing lens cover: Mounting lens cover Turn the lens cover according to the illustrated direction until it separates from the SP360 4K. % Lens ring and lens cover cannot be used at the same time.
Installing Battery 1. Open the battery cover 2. Insert the battery Push the battery cover lock along the direction of arrow ʒ , push the battery cover along the direction of arrow ʓ , and open the battery cover along the direction of arrow ʔ . Insert the battery into the battery compartment along the direction of arrow ʕ (note the location of the + and - symbols) 3 2 1 4 3. Close the battery cover Cover the battery cover along the direction of arrow ʖ .
Installing Memory Card 6 into the slot completely, and then close the side cover. 6 A memory card (microSD / microSDHC / microSDXC) is optional and is not included in the product package. It needs to be purchased separately. Please use an original memory card, which is Class 10 or higher and has a capacity of 8GB to 128GB.
Charging the Battery + Charging the battery with a battery charger: 1. Place the battery into the battery charger according to the direction illustrated. Use the Micro USB cable to connect the battery charger and the AC adapter, and then plug the AC adapter into an electrical outlet. 2. The indicator light will turn red while charging.
Charging the camera with a computer: 1. Place the battery into the camera. 2. Use the Micro USB cable to connect the camera (Off) to a computer (On).
Main Interface Introduction The Main Interface 1. Mode 2 3 4 Movie mode Snap Shot Photo mode Loop recording mode 5 1 / / / / / Time Lapse mode High-speed movie mode 8 7 Burst mode 6 2. Memory card / / + / / / / / / / / / / / / / / 4. Battery status 5. Motion detection (On) 6.
Power On / Off Power on: When the power is off, press and hold the button for more than one second to turn on the product. Power off: When the power is on, press and hold the button for more than one second to turn off the product. If the product cannot be powered off normally, you can remove the battery from the camera to force it to power off. Start-up for language, date and time 1.
Modes Introduction In the main interface, press the button to enter the mode selection interface. Press the or button to select any one mode; press the button to the main interface of the current mode. , Snap shot photo mode 6 modes are available: Movie mode Burst mode , Loop recording mode , Time Lapse mode , High-speed movie mode , . Movie mode Enable video recording. It is suitable for recording in most conditions. Operation method: Press the button to start recording.
Snap Shot Photo mode Enables photo shooting. It is suitable for recording in most conditions. Operation method: button for photo. Press the Loop recording mode Loop recording refers to recording independent video segments in the unit of 2 minutes. The camera is only capable of saving a video of 60 minutes once maximally. If the recording at a time exceeds 60 minutes, the new video will automatically cover the earliest record in the folder in the unit of 2 minutes.
High-speed movie mode The product shoots ultra-high speed movies, and plays back with normal 30fps speed Operation method: Press the button to start recording. Press the button again to stop recording. Burst mode Enables ten photos to be captured continuously before auto pause. Operation method: Press the button; it will stop after 10 photos are taken.
Introducing the Menu 1. In the main interface, press the / / / % ), General Settings, Remote Pair Settings. Press the or ] * * button to select the item, and press the / / button to enter the corresponding secondary level menu interface. % 2. Press the or button to select the item; press the 3.
Every Shooting Mode Settings / / / / / ) The secondary level menu in every shooting mode Movie Settings % interface Loop Recording Settings Time Lapse Settings High-speed Movie Settings Snap Shot Photo Settings Burst Settings The secondary level menu interface 22
Take the recording setting menu as an example; the setting operating manners of other shooting modes are the same as that of the recording setting menu.
Display mode Set image storage form.
Movie size Set video resolution.
Motion detection Motion detection means that if the product detects moving objects entering into the view, it will automatically start recording. During the recording process, if there is no moving object detected for 10 continuous seconds, the recording will pause automatically. There are 2 options : ] Off Operation method: 1. Select , and return to the main interface. 2. The display will show the icon. Press the button to activate.
White balance White balance means that the user adjusts the color temperature under different light sources to ensure that the colors are reproduced correctly. There are 6 options : When enable the night view function, white balance will be set as Z Underwater automatically. Photo size Set photo resolution.
General Settings % % % 28
Volume Set the volume of the product. There are 2 options : ] Off Power off When this function is enabled, if there are no actions taken within a set time frame (except while recording or connected to Wi-Fi), the product will automatically shut down. There are 2 options : Off USB connection mode The mode of connecting the Micro USB wire to the computer is set. If there is need to read or save videos, please select Mass Storage.
Format Format can clear all data stored in the memory card. There are 2 options : , press the If select Cancel 6 Reset settings Reset settings can recover all product settings to the factory defaults (except for date and time).
Remote Controller The remote controller is an optional accessory. If you need one, please contact the local retailer to buy separately or access www.kodakpixpro.com to check more customer service details. You can wear the remote controller on the wrist to perform long-distance control on the camera by operating the remote controller. Remote Controller Appearance Introduction 1. RF signal indicator lamp 2. 7 6 5 1 2 3 4 RF signal test button 3. Mode switch 8 4. Battery/Bemory card indicator lamp 5.
Install Battery: The battery cover is turned by use of a coin to open, the battery is put in (the anode is upwards), and then the battery cover is turned reversely to close. Use Method: 1. Press the button in the main interface of the camera, select pairing confirmation interface, and finally select and press the , press the button to select "Single Control", and then press the button to enter a button to confirm.
2. Simultaneously long press the buttons and on the remote controller until pairing is successful. 3. Set the desired shooting mode (recording mode or shooting mode ) and the display mode (spherical or square ). Other parameters are set as the current same modes of the camera. 4. Press the button on the remote controller to shoot or start recording, and press the 5. To terminate remote control, just press the button again to stop recording. button in the Remote Off interface.
When appears on the interface, indicates that the camera is out of control of the remote controller at the moment. indicates that the camera is under the control of one remote controller at the moment. In case of successful pairing between the camera and the remote controller (the camera is capable of memorizing the remote controller paired successfully last time): 1. If the camera is turned off, the camera is turned on to automatically start recording by pressing and holding the button. 2.
Using Interfacing Micro USB interface Charging 14 Using an external power supply In case of low battery power, or when a long-term power supply is needed, an external power supply (AC adapter, vehicle power supply, portable power supply or other power unit) can be used instead of a battery. At this time, the setting of functions, photography, and other operations can be performed. When powered on, use the Micro USB cable to connect the camera to an external power supply.
Micro HDMI interface The television (on) up to the HDMI standard and the camera (on) are connected by use of a Micro HDMI wire (bought independently). After the connection succeeds, the documents in the memory cards of the camera are displayed on the television, while is displayed on the camera. The shooting and playback functions can be realized by use of the camera: 1. Press the button to switch between the video playback mode, the photo playback mode and the shooting mode. 2. Press the or 3.
Wi-Fi Mode Download and Install App Smart Device: Download the App installation package (App name: PIXPRO SP360 4K) to your smart device from the path below, and install it by following the instructions on the interface. For Android devices, search and download the App "PIXPRO SP360 4K" in Google play, and install it by following the instructions on the interface. For iOS devices, search and download the App "PIXPRO SP360 4K" in App Store, and install it by following the instructions on the interface.
Connect camera to smart device (or PC) with Wi-Fi. Operation method: 1. Camera : **Z * * Z +Z +>&*+&@¡ (initial password: 12345678) indicated on the label in the battery compartment of the camera. Press the button to enable Wi-Fi mode. The camera will enter 2. Smart Device or PC: Enable Wi-Fi mode, it will automatically search the nearby Wi-Fi hotspots.
If the Wi-Fi connection is cut off while recording, the camera will continue to record and enter the connectionless recording interface. When displays in the interface, press the button, and press the or button to select , and then press the button to exit the Wi-Fi connection.
Connect camera to smart device with NFC 1. Enable NFC mode on your smart device. 2. Use your smart device to lightly touch the NFC mark on the camera. If the smart device has a prompt tone or vibration, it means the connection is successful. 3. The App will open automatically on your smart device.
Appendices [ Image Sensor Type 1/2.3" BIS CMOS Effective Pixels 12.40 Megapixels Total Pixels 12.76 Megapixels Focal Length 0.850mm ]# 8.20mm F number F2.
Photo Exif 2.3 (JPEG) Movie MP4 [Image: H.264; Audio: AAC(Stereo)] File Format Modes Movie, Snap Shot Photo, Loop Recording, Time Lapse, Burst, High-speed Movie Splash proof Equivalent to JIS/IEC IPX5 (Body) Shockproof Up to 2m (with lens cover) Dustproof Equivalent to JIS/IEC (IP6X) -10°C & LCD 1.
Power Rechargeable Li-ion Battery LB-080, 3.6V 1250mAh, In-Camera Charging Shooting Capability (Battery Performance) Approx. 160 shots (Based on CIPA Standards) (Wi-Fi on) Approx. 55 minutes for Video (@4K/30fps) (Wi-Fi on) Operation Environment Temperature: -10 ~ 40°C, Humidity: 0 ~ 90% Dimensions (W×H×D) Approx.46.5×50.0×53.0 mm (Without lens cover) (Based on CIPA Standards) Weight Approx.
Prompts and Warning Messages Message Description % 6 When pressing the button for shooting, the memory card cannot be accessed Processing mode 6 choose to delete or format. because there are too many folders. No memory card is detected in the camera. When turning on the product or pressing the Insert the memory card. button, the product detects that the memory card is out of capacity.
Message Description Processing mode The camera is set as "Mass Storage", connecting to the computer USB. User should do nothing. The camera is set as "Web Cam", connecting to the HDMI device. User should do nothing. Connecting to the HDMI device. User should do nothing. A warning for low battery before shutting down automatically. % Charge or replace with a new battery. ' User should do nothing.
Trouble Shooting Problem Product does not turn on Possible causes The battery has been depleted. Solution Charge the battery. The battery is installed incorrectly. Please follow the charging instructions in the manual to install the battery. Blurred images There is dirt on the lens or the lens cover. Clean with a clean, lint-free dry cloth. Failed to connect Wi-Fi Wrong password entered. Please re-enter the password.
Special Accessories There are different options of SP360 4K accessories available. Accessory bundles vary per retailer. To purchase additional accessories separately, please contact your local retailer customer service support, or visit www.kodakpixpro.com for more customer service details.
Installation method: 2. Press the lock downward until it locks tightly. Install the waterproof housing on the other accessories, and use the set screw to tighten. 1. > ! lens cover, place the camera and anti-fog inserts into the waterproof housing.
! " # $ objects $ % & Curved Adhesive Mount: For tacking onto a helmet or other curved objects Installation method: % [ Both types can be assembled in the same way: 1. Assemble the standard housing (or the waterproof housing). 2.
Bar Mount: For mounting on bicycle handlebars, sailing masts, and other tube-like objects Installation method: 1. Set the bar clamp to the handlebar and rotate the screws to tighten. 2. Assemble the standard housing (or the waterproof housing). 3. Assemble the standard housing (or the waterproof housing) and bar clamp in accordance with the direction illustrated in the picture, and use the setscrew to tighten.
Suction Cup Mount: For attachment to automotive windshields (or smooth surfaces) Installation method: 1. Assemble the standard housing (or the waterproof housing). 2. Assemble the standard housing (or the waterproof housing), the adapter, pretightening nut and suction mount in accordance with the direction illustrated in the picture, and tighten the pre-tightening nut. Adapter 3. First, clean the suction mount and the windshield before attaching the suction cup to the windshield.
Licensed Product The Kodak trademark and trade dress are used under license from Kodak. © 2015 by JK Imaging Ltd. All Rights Reserved. JK Imaging Ltd., 17239 South Main Street, Gardena, CA 90248, USA JK Imaging Europe, 71 Clarendon road, Watford, WD17 1DS, UK www.kodakpixpro.com Ver.