日本語 English Digital Photo Printer CHC-S2245-5 Operation Manual http://www.sinfo-t.
Handling of this Manual 1. All rights reserved. No part of this operation manual covered by the copyright herein maybe reproduced or copied in any form or by any means, including translation, without the written permission of SINFONIA TECHNOLOGY Co., Ltd. 2. The specifications in this operation manual are subject to change without prior notice. 3. In case of having any difficulties or finding the fault in this manual, your information to SINFONIA TECHNOLOGY will be highly appreciated.
CONTENTS PREFACE Chapter 1. Important Safety Instruction ・・・・・・・・・・・・・・・・・ Environments ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ Handling Instruction ・・・・・・・・・・・・・・・・・・・・・・・・・・ Handling Instruction for Consumable and Printed Output ・・・・・・ 1-1 Chapter 2.
Chapter 1. Important Safety Instruction This manual provides detailed instructions for the safety use of the printer. Read this manual before operating the printer to ensure to have proper use. ◆In this manual, there are notes that require special attention. ◆ For your safety operation, Safety notices are separated as follows; Warning: Inappropriate handling can cause the death or serious wound. Caution: Inappropriate handling can cause the wound for the users and/or cause the physical damage.
Chapter 1. Important Safety Instruction Handling Instruction In handling the printer, please pay attention to the followings; Warning: Lift the printer from its box and put it onto a flat table or desk. Warning: At nearly 10Kg, the printer is too heavy to be lifted by one person. Also please take a good care of your hands and fingers when lifting the printer from the box. Warning: Be careful when you transport the printer on the slippery floor.
Chapter 1. Important Safety Instruction Handling Instruction for Consumable and Printed Output In handling the ink ribbon, paper and printed output, please pay attention to the followings; Attention: Paper Handling ・Use the paper specified by SINFONIA TECHNOLOGY. ・Store the paper flat. ・ Store the paper in a dry and dark place to avoid the direct Sunlight. (Temperature less than 30C, Humidity less than 60%). ・Do not touch the paper surface before printing to avoid the fingerprints.
Chapter 2. Installing and Set Up This chapter explains the unpacking and set up of the printer. Before proceeding to this chapter, please make sure to read Chapter 1. Important Safety Instruction. Unpacking and Checking the Accessories 1. Open the box and remove the box containing the accessories and protection materials. Attention: Keep the packaging materials. The box and protection materials are necessary when moving or transporting the printer. Make sure that they are retained. 2.
Chapter 2. Installing and Set Up Parts Name and Function ① ② ③ ⑤ ④ ⑥ ⑦ ( Front View) ( Rear View) ⑧ (Internal View) № Name Function ① Open Lever When open the Open Unit, hold this lever. ② Printer Status Lamps Printer status display lamps are located on the panel. ③ Open Unit Open the Open Unit when replacing an ink ribbon or paper, or when performing maintenance. ④ Dust Box The Dust Box stacks trim dusts. ⑤ Power Switch This switch turns on/off the power of the printer.
Chapter 2. Installing and Set Up Printer Status Lamps Name and Printer Status Printer status lamp display ●:on, ○:off, *:flashing Group - 1 2 3 LED Display Status POWER ERROR Paper Set ○ ○ ○ * ○ The printer is initializing after turn on the power Thermal head is cooled/heated on printing. The printer is loading paper or ribbon. ● ○ The printer is ready ● * ○ ● * ●(Blue) ● * *(Purple) The printer could not take up the ink ribbon.
Chapter 2. Installing and Set Up Connecting Power Cable Insert the power cable attached to the printer into the power connector located on the rear of the printer. Warning: In case of not using the printer for a long time, remove the power cable for safety. Warning: Avoid “piled up” connection. It can cause the fire and electric shock. Connecting USB Cable Warning: Make sure to turn off the power of the printer before inserting the power cable.
Chapter 2. Installing and Set Up Loading Paper Turn on the power of the printer by pressing "|" on the power switch. 1. In case that trim dusts are stacked in the 4. Set the paper in the printer. After setting the paper, remove the seal from the paper. dust box, make sure to throw them away. 2. Pull the lever to open the Front Cover. 5. Insert the edge of paper under the guide roller by rotating the paper flanges. Insert the paper until the PEPERSET Lamp is lit in blue.
Chapter 2. Installing and Set Up Setting Ink Ribbon 1. Set the ink ribbon to the Open Unit as shown 4.Insert the claw of the dust box first and insert the projected section of the printer in the hole at the bottom of the dust box. 2. Take the slack the ink ribbon by turning the ink ribbon supply core. OK × Caution: The dust box is not set correctly if there is a gap between the front cover and the dust box.. 3. Close the Open Unit. When close the Open Unit, press on the center of the open guide unit.
Chapter 3. Routine Maintenance Cleaning of Thermal Head, Platen, and Cleaning Roller By using thermal transfer technology, daily maintenance is not really necessary if the printer is being use properly. However, in order to keep the best print quality, it is recommended to do the cleaning of Thermal Head, Platen, and Cleaning Roller once in a month. Caution: Make sure that the power is turned off before starting cleaning. Thermal Head reaches high temperature just after printing.
Chapter 3. Routine Maintenance 4. Using gauze dipped with isopropyl alcohol or ethyl alcohol, clean the rubber section of the Cleaning roller Attention: Printing should be performed after the alcohol dried up completely (approx. 5 minutes) Cleaning of Outer Cover Wipe the printer outer cabinet with a soft cloth. If the stains are not removed, wet the cloth and apply weakened neutral Detergent to it.
Chapter 4. Error Handling Printer Status lamps are displayed in red When the error happens, the details of the error can be confirmed with the printer status lamps. Printer Status Lamps and Paper Setting Lamp display ●:on、○:off、*:flashing Status LED Display Group Corrective Action POWER ERROR Paper Set ● * ○ ● * ●(Blue) ● * * (Purple) The printer could not take up the ink ribbon. ● * ● (Purple) The ink ribbon loaded is not supported. ● * *(Red) Paper jam occurred.
Chapter 4. Error Handling Paper Jam Power Supply Interrupted during Printing 1. Open the Open Unit. In case, power supply interrupted during the printing, Thermal Head will be kept pushing to Platen. Leaving this situation for a long time, shape of Platen can be warped. In order to avoid this situation, please follow the instruction below. 2. Cut off the folded section or printed section with scissors. When the paper is folded inside of the printer, pull it out slowly. 1. 2. 3.
Chapter 5. In order to more comfortably use Paper Pre-Cut function can be turned off through the printer driver. Caution: Dust on the surface of the paper may damage the thermal head. Clean the dust on the paper surface and install the paper roll into the printer. Caution: Clean the finger print on the paper surface to avoid the finger print on the print image. Caution: Paper may be installed and fixed on improper direction, but maybe oblique direction.
Chapter 5. In order to more comfortably use For the Customers in the U.S.A. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Chapter 5. In order to more comfortably use For the Customers in Europe This product shall not be used in the residential area. This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Hereby, SINFONIA TECHNOLOGY CO., LTD. declares that the radio equipment type CHC-S2245-5(RFID 13.56MHz) is in compliance with Directive 2014/53/EU.
Specification Product name Model name Printing method Resolution Print sizes Color Stream S3 CHC-S2245-5 Dye sublimation thermal transfer 12 dots/mm (300 dpi) 51 mm x 152 mm (2 x 6 size) 102 mm x 152 mm (4 x 6 size) 152 mm x 203 mm (6 x 8 size) Print media Paper 152 mm (6 in.) width roll paper for print 900 sheets/roll (in case of 4 x 6 size prints) 450 sheets/roll (in case of 6 x 8 size prints) (Same as each printable size of dye-sub print.