Installation Guide

70g双胶纸/432*250mm/正反印刷/单色
正面 反面
1. Make sure the POWER IS TURNED OFF at the source to the
location in which you are installing the product.
2. Use template inside box to cut hole in ceiling. (Fig. 7)
3. Select desired lumen output and CCT.
(Fig. 8)
5. Push until the trim sits flush against the ceiling.
(Fig. 10)
Fig: 1Fig: 1Fig: 7
Fig: 1Fig: 1Fig: 8
INSTALLATION WITHOUT EXISTING FRAME
INSTALLATION
WITHOUT EXISTING FRAME (cont’d)
4. Insert lamp conduit into a preinstalled J-box (not provided) and
wire to the power source (black to hot, white to neutral, green
to ground).For 0-10V dimming circuits, connect pink to pink and
purple to purple. Close the J-box securely.
Install the downlight by lifting both retention tabs upward.
(Fig. 9)
Fig: 9FFig:
Fig: 1Fig: 1Fig: 10
DIMENSIONAL DRAWINGS
8 1/4” 4 5/8”
6 1/4”~ 7 1/2”
5 1/8”
6’’ 8’’ 9.5’’
5 7/8”
7 7/8”~
10 1/4”
5 1/4”
9”
6 3/8”
9 ”~
11 1/2”
10 5/8”
6 1/8”
INSTRUCTIONS
Field Adjustable Performance Downlight
INSTRUCTIONS
Field Adjustable Performance Downlight
INSTRUCTIONS
Field Adjustable Performance Downlight
WHAT’S IN THE BOX OPTIONAL ACCESSORIES
Goof Ring
Templat
DIAMETER: XX’’(XX mm)
e (1)Downlight (1)
8-10 GR
for extending from 8-1/4” to 10-1/2”
Maximum Ceiling Cutout 9”
10-12 GR
for extending from 10-1/4” to 12-1/2”
Maximum Ceiling Cutout 10-15/16”
12-14 GR
for extending from 11-1/2” to 14-3/16”
Maximum Ceiling Cutout 12-3/8”
SJ-Plate
New construction plate for Stud/Joist
T-Plate
New construction or remodel plate for
T-grid ceilings
TOOLS NEEDED
2. Remove the old housing for lamp.(Fig.1)
5. Adjust the fixture power to desired lumen output by sliding
the black selector switch. Adjust the color temperature to
desired one, by sliding the red selector switch.(Fig.4)
3. Attach the carabiner safety clip to the existing fixture
housing.(Fig.2)
4. Remove junction box faceplate. Disconnect all wires to the
ballast and remove ballast from J-Box. Remove appropriate
round knock out and attach the fixture conduit whip into
knock out. Connect incoming power (White to White, Black
to Black, Green to Green/Ground). For 0-10V dimming circuits,
connect Grey to Grey and Purple to Purple. Reattach J-Box
faceplate.(Fig.3)
INSTALLATION WITH EXISTING FRAME INSTALLATION WITH EXISTING FRAME (cont’d)INSTALLATION WITH EXISTING FRAME
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
Fig: 1Fig: 1Fig: 1
Fig: 1Fig: 1Fig: 2
Fig: 1Fig: 1Fig: 4
Fig: 4Fig: 4Fig: 3
6. Install the downlight by lifting both retention tabs upward.
(Fig.5)
Fig: 2Fig: 2Fig: 5
7. Push until the trim sits flush against the ceiling.
(Fig.6)
8. Restore power at the source and the installation is complete.
Fig: 2Fig: 2Fig: 6
MI PORTANT
WARNINGS:
•
•
•
•
•
CAREFULLY BEFORE INSTALLING FIXTURE. R TAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. READ E
required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
•
•
•
•
•
.
Risk of electrical shock. Disconnect power at fuse or circuit breaker before installing or servicing.
To prevent early lamp failure, lamp should only be installed in operating environments ranging between-30
℃ and +40℃
(-22°F and+104°F).
No user serviceable parts inside. To avoid electrical shock do not disassemble product.
WARNING- Risk of fire or electric shock, LED Retrofit Kit installation requires knowledge of luminaires electrical systems.
If not qualified, do not attempt installation. Contact a qualified electrician.
WARNING- Risk of fire or electric shock, Install this kit only in luminaires that have the construction features and
min dimensions shown in the Template and where the input rating of the retrofit kit does not exceed the input rating
of the luminaire.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation
WARNING- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder
terminals, Instead installers should cut existing lampholder leads away from the lampholder and make new electrical
connections to lampholder lead wires by employing applicable connectors.
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. Product must be installed by a qualified electrician
in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local
national regulations for electrical installation.
This
2021年11月08日
与包装文件一致
说明书_LED_S107_120V-277V_6寸_8寸商照筒灯_V03