Cylindrical RF Lock SV1C State of: December 2006
SV1C Cylindrical RF Lock Page 2 1.0 Important Information .................................................................... 3 2.0 Operation......................................................................................... 4 3.0 4.0 2.1 General Information ............................................................................ 4 2.2 Opening and Locking From Outside.................................................. 4 2.3 Opening and Locking From Inside...............................
SV1C Cylindrical RF Lock Page 3 Important Information Safety remark: Caution! – Incorrect handling of the batteries and storage batteries used in this product can result in the risk of fire or burns. Do not charge, open or burn these batteries or heat them to more than 100 °C (212 °F). Installation of a SimonsVoss RF Lock requires knowledge in the areas of door mechanics, door certifications, installation of electronics and the use of the SimonsVoss software.
SV1C Cylindrical RF Lock Page 4 An incorrectly installed RF Lock may block the access through a door. SimonsVoss Inc. is not liable for the consequences of incorrect installation, such as blocked access to injured or endangered persons, property damage or other damages. If you will be storing the RF Lock for more than one week, remove the backup battery. 1.0 Operation 1.
SV1C Cylindrical RF Lock Page 5 1.3 Opening and Locking From Inside It is always possible to open doors with the SV1 RF Lock from the inside without operating the transponder 2.0 Additional Functions You can activate the following functions with the software settings: 2.1 OMRON All product versions can be operated in OMRON mode. You will find a detailed description in the Smart Relay manual. 2.2 Extending the Unlock Time The default unlock-time for the RF Lock is approximately 3 seconds.
SV1C Cylindrical RF Lock Page 6 3.0 Battery Warnings 3.1 RF Lock Warning level 1 for main battery If the main battery of the lock goes empty, eight short signal tones, coming quickly one after another, sound after you operate the transponder and before the cylinder unlocks. You must replace both batteries now. Warning level 2 for backup battery (SW Version 10.0 & SW Version 10.
SV1C Cylindrical RF Lock Page 7 3.2 Transponder If the transponder battery voltage is getting low, eight short signal tones, coming quickly one after another, sound each time the transponder is operated on the lock after the unlock. Do not take out the transponder battery because this will probably result in the loss of data. See the “Transponder” manual for more information. 4.0 Battery Replacement Only authorized personnel are permitted to replace the battery.
SV1C Cylindrical RF Lock Page 8 Replace the battery cap by aligning it so that it slides on easily and then twist a few degrees in the clockwise direction until it locks in place. If the inner rose was removed, replace it so the access hole is lined up to allow the replacement of the set-screw. Use a 7/32 Hex key to replace the set-screw being careful to hold the inner handle so that it does not fall off.
SV1C Cylindrical RF Lock Page 9 5.2 Unpack Pack A. Remove the lock components from the box.
SV1C Cylindrical RF Lock Page 10 5.3 Mark Door Mark horizontal line across edge of door 40 5/16” (1024mm) is standard height from floor. Fold template over edge of door, centering on horizontal line. Mark centers of holes at proper backset.
SV1C Cylindrical RF Lock Page 11 5.4 Drill Door A. Drill 2 1/8” (54mm) diameter hole through the door. B. Drill 1” (25mm) diameter hole in edge of door. Cut out for latch front 1 1/8” (29mm) wide by 2 ¼” (57mm) high by 5/32” (4mm) deep. Check latch unit for proper width front and square or round corners. C. Drill two (2) 5/16” (8mm) diameter holes through door. Caution: To avoid splintering wood drill holes through both sides of door.
SV1C Cylindrical RF Lock Page 12 Install Latch Unit Insert latch unit in door. (Be sure bevel edge of bolt faces strike plate.) Attach with two screws supplied.
SV1C Cylindrical RF Lock Page 13 Install Lock Insert the inside rose support assembly into door from inside making sure that lock body frame hooks latch case and retractor engages bolt tail(s). DO NOT FORCE (If lock body does not engage latch easily, check door preparation for errors.
SV1C Cylindrical RF Lock Page 14 Install Outside Components A. Choose and install the anti-rotation plate on the outside of the door. For a 1 ¾” door use the deep plate. For a 1 3/8” door use the flat plate. B. With the battery arrow pointing up on the inside, slide the outside lever assembly onto the lock shaft. Fasten rose assembly with two through bolts from the inside.
SV1C Cylindrical RF Lock Page 15 Install Inside Components A. Place rose on inside rose support assembly so that the side hole points towards the shut face of the door. Snap into place against the door. B. Install the inside lever handle. Fasten inside lever handle with setscrew inserted in the side hole of the inside rose. C. Rotate the rose so that the side hole faces down. The rose will snap in to place.
SV1C Cylindrical RF Lock Page 16 Strike Installation (Wood Frame Only) A. Close door and mark a horizontal line from the center of the template to the frame of the door. B. Measure half the thickness of the door; mark this same distance with a vertical line starting from the stop side of the frame and where both lines cross make a 1” (25mm) diameter hole and 1/2” (13mm) in depth. C. Align the holes of the strike with the vertical line, trace the outline of the strike and mortise to 1/16” (1.6mm) depth.
SV1C Cylindrical RF Lock Page 17 5.5 Troubleshooting 1. Check door. 2. Check hinges. They should not be loose or have excessive wear on knuckles. 3. Latch will not deadlock. Either strike is out of line or gap between door and jamb is too great. Realign strike or shim out towards flat area or latch. 4. Latch does not retract or extend properly. Latch tail and retractor not properly positioned. i. Remove lockset. Look through 2 1/8 hole and verify latch tail centered between top and bottom of hole. ii.
SV1C Cylindrical RF Lock Page 18 6.0 Data Sheet Levers Material Stainless steel Styles Castle Manor Harbor Battery Finishes 630 Satin Stainless Steel 629 Bright Stainless Steel 606E Satin Brass 605E Bright Brass 619E Satin Nickel 613E Satin Oil-Rubbed Bronze Type (2) Lithium 3 V, CR2450 Use only original replacement batteries from SimonsVoss Approx.