USER AND INSTALLATION MANUAL VIDEO PROJECTOR MANUALE D’USO E INSTALLAZIONE SVD 500 PLUS SVP 450 PLUS SVP 420 HB
SVP 450 PLUS - SVD 500 PLUS 1- WARNINGS ......................................................................................... Page 3 1.1 Safety and Regulations ............................................................. 4 2- GENERAL INFORMATION ................................................................. 2.1 Projector identification ............................................................... 2.2 Power cabling ............................................................................ 2.
SVP 450 PLUS - SVD 500 PLUS 5- 678910111213- THE COMPLETE FUNCTION RC 3000 REMOTE CONTROL .......... Page 24 5.1 Complete function RC3000 remote control ............................... 24 5.2 Batteries .................................................................................... 28 5.3 How the RC 3000 remote control works ................................... 25 5.4 Videosetup ................................................................................ 25 5.4.
SVP 450 PLUS - SVD 500 PLUS CAUTION ELECTRIC SHOCK HAZARD DO NOT OPEN ! To reduce the risk of electric shock, disconnect the power supply cable before opening the equipment There are no parts inside the projector that need adjusting by the user. Qualified technicians must be called to perform extraordinary maintenance and adjustments. This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules.
SVP 450 PLUS - SVD 500 PLUS 2.1 Projector Identification MAINS POWER Mains power: 120-240Vac 50-60Hz +6%-10% Max absorbed current: 2.5 ARMS The model and serial number are located on the projector’s rear label Fig. 1. 1.1 Safety and Regulations A) Safety - conform to: EN60950: Equipment for information technology including electric office equipment. Safety.
SVP 450 PLUS - SVD 500 PLUS If the power socket is not equipped with an earth pin, call your electrician who will install it and ensure its efficiency. To disconnect the cable pull it out with the plug. - If the projector is not used for long periods of time or during storms, unplug the projector temporarily from the mains to avoid damaging the projector caused by lightning or temporary overcurrents. Do not pull the cable itself.
SVP 450 PLUS - SVD 500 PLUS 2.5 Cleaning the projector 2.6 Packing the Projector When we speak about projector cleaning we mean the outside of it. NO internal cleaning is necessary. For the best protection pack the projector as it was originally packed at the factory. For air freight shipping use metal or plastic straps to secure the box. - Before you start cleaning the projector take the plug out of the mains.
• THE FOLLOWING FUNCTIONS ARE ON THE PANEL: Picture adjustment. Each time you press a button you select one of the follow controls: Contrast, Brightness, Colour-Hue, Peaking. Use the + and - buttons to modify the value of the selected control. INFO Press this button to have the current projector settings (ref. INFORMATION paragraph) 1- Power switch. 2- Fuse holder. The fuse type is 5A, T delayed.
SVP 450 PLUS - SVD 500 PLUS 3 USER REMOTE CONTROL RC 3100 RC 3100 is the User Remote Control for normal programme selection and analogue adjustments (once the projector is installed). The projector is controlled by the infrared ray remote control (I.R.) whose maximum range is approximately 10 metres with new batteries. The following figure describes the functions of the buttons on the User Remote Control. To select the signal input wanted directly. Also used to turn the projector ON.
SVP 450 PLUS - SVD 500 PLUS 3.1 Batteries Handling the remote control and batteries: Deutsch English Espanol Francaise Italiano Portoguese - Avoid exposing the remote control to heat and humidity. - When not using the remote control for a long period of time, remove the batteries. - Do not use new and old batteries together or batteries of a different voltage or type. - Do not drop or mishandle the remote control. The left arrow indicates the language in use.
SVP 450 PLUS - SVD 500 PLUS 3.8 VCR button (Sync filter) COL 50 To select the appropriate sync filter. Press VCR to change the sync time constant. The following message will be diplayed: CON 80 LUM 35 PEAK 90 TIN 50 STORED TIN 50 FAST Each time this button is pressed, a different adjustment will be selected, sequentially. Use the arrows to change the value, press MEMO to store the new value. Press ESC to exit.
3.10 Muting video button Press EXIT to return to the previous menu. Press ESC to exit the menu. Press MUTE for about 2 seconds. The picture will darken while the projector stays on; the picture will reappear immediately if you press the button again. To turn on or off the noise reduction: this menu allows you to activate a frequency filter. Press for at least 2 seconds, the following menu will be dispalyed: Use the arrows to select NOISE RED.
SVP 450 PLUS - SVD 500 PLUS Use the arrows to select TLV SYNC and press ENTER to confirm, the second menu appears: VIDEO MENU BLANKING H. = 00 TLV SYNC V. = 00 Press the arrows to change the figures relevant to the vertical size of the blanking window on the lower part of the screen. Press the arrows to change the value of the horizontal size of the blanking window on the right part of the screen. Press MEMO to store the adjustements carried out. Press EXIT to return to the previous menu.
The setting USER ADJUSTMENT regards an optional colour temperature setting, which must be carried out by a QUALIFIED TECHNICIAN upon installation, should the end user wish a different colour temperature than the set ones. The 3200° K colour temperature is used only when the projector is placed inside television studios. The 6500° K colour temperature is mostly used being considered the most pleasant and the one that reproduces colour most faithfully. switched on.
SVP 450 PLUS - SVD 500 PLUS All peaking, hue, colour, brightness and contrast values are now stored. To recall the SET adjustment, press displayed. In order to prevent the final user from gaining access and carrying out unnecessary installation adjustments, the projector is equipped with a special protection key. Observe the following procedure to unlock it and gain access to the installation mode. , no message is Press the button • • • for 2 seconds.
SVP 450 PLUS - SVD 500 PLUS 4.1 INSTALLATION PROCEDURE Qualified personnel must carefully observe the installation procedure to install the projector and to ensure best performances. C B Note: The projector is factory-set for front ceiling projection with a 90” screen, 4/3 format and a projector-screen distance of 265 cm. 1. Choose the installation type and read the instructions through carefully. Determine the distance between the screen and the front of the projector. Determine the projection angle.
SVP 450 PLUS - SVD 500 PLUS - 4.3.2 Desk-top front projection - Correct use of the spacers, as shown in the spacer tables, is mandatory for a perfect focus uniformity. Check that the projector is perfectly stable. - Measure the screen diagonal and take the nearest value from the table. Calculate the ratio between the table value and the relative width. Multiply the value obtained by the actual screen width. Example: Suppose we have a 105” screen diagonal.
SVP 450 PLUS - SVD 500 PLUS - 30 0 = ENGLISH - 93 F - If the measurement of the screen diagonal is not in the table, C can be determined (in cm) as follows. Measure the screen diagonal and take the nearest value from the table. Calculate the ratio between value C and screen width in the table. Multiply the result by the actual screen width. T N O R - BRACKET Example: Suppose we have a 105” screen diagonal. 100” is the nearest value in the table. Ihe C/Width ratio is equal to :305/203.2=1,5.
SVP 450 PLUS - SVD 500 PLUS 5- Turn the projector upside down and hang on the ceiling with the assembly brackets. 6- Tilt the projector to centre the vertical picture and screw the two securing screws (H) D = Distance between the line of the first hole of the assembly bracket and the screen. Note: The screen size refers to the useful area (4/3 format). Note: Insert the special curved washers between the ceiling bracket and the securing screws.
SVP 450 PLUS - SVD 500 PLUS 4.5.2 Spacers table To change the spacers first of all remove the top cover and front panel. Now slightly loosen the 4 screws (A) for each tube, change the spacers (B) (see the spacers table) and then tighten the screws. You can only see two screws in the figure because the other two are under the projection tube.
SVP 450 PLUS - SVD 500 PLUS 200" 120" BLUE GREEN BLUE RED 1 1 0,2 1 1 1 0,2 1 0 0,2 0 0 0,2 0 1 0,2 1 0,5 1 0,3 0 0,2 0 1 0,3 0,2 1 0,5 0,2 1 0,5 0 0,2 0 1 0,3 1 1 0,5 0,2 0 0,2 1 0,5 0 1 1 0,5 0,3 0,2 0,2 0 0,2 0 GREEN 0,3 0,3 1 0,5 0,2 0,5 0,2 1 0,5 0,3 0,2 0,3 0 0 0,3 0,2 0,5 0,3 1 0,5 0,2 0,5 0,2 1 0,5 0,3 0,2 0,3 0 0 0,3 0,2 1 1 0,2 1 1 1 0,2 1 0,2 0,3 0 0 0,3 0,2 250" 150" BLUE RED GREEN BLUE RED GREEN RED 0,5 0,2 1
SVP 450 PLUS - SVD 500 PLUS 4.6 Projector centering Projections at 0° GREEN RED 0 0,5 0,2 0 0 0,5 0,2 0 0 0,5 0,2 0 0 0,5 0,2 0 The first step towards a good installation is centering the projector with respect to the screen.
SVP 450 PLUS - SVD 500 PLUS 4.8 Lens focus adjustment 4.9 Mechanical centering of the tubes Each lens must be focused individually with the tubes on, one at a time and following this procedure: Select the CROSS HATCH signal with the remote control. For an installation different to factory setting (90”) the mechanical centering of the red and blue tubes needs to be adjusted. Looking at the following figure, unscrew (only 2 turns!) the screws (A-B-C-D) of the blue tube. 1.
SVP 450 PLUS - SVD 500 PLUS 6. Turn on the projector. 7. Select the type of installation by means of the remote control RC 3000. 8. Use the menu DEF CENT (H and V) by means of the remote control RC 3000 to shift the picture on the screen. RED WIRE HORIZONTAL DEFLECTION CONNECTORS A B R BLUE GREEN WIRE G Observe the following instructions, only if the image is not centered in the tube.
SVP 450 PLUS - SVD 500 PLUS 5 THE COMPLETE FUNCTION RC3000 REMOTE CONTROL 5.1 Complete function RC3000 remote control There are two remote controls for the video projector. One, the RC3000, is a complete function remote control used to install the projector while the other one, the RC3100, is for normal use. Both control the projector with infrared rays. With the RC3000 remote control you can connect via cable directly to the video projector’s IR input so as to avoid any technical problems. N.B.
5.2 Batteries 5.4 Video setup Handling the remote control and batteries: 5.4.1 5.4.2 5.4.3 5.4.4 5.4.5 - Avoid exposing the remote control to heat and humidity - When not using the remote control for a long period of time, remove the batteries. To change the Y/C delay. To switch on/off the comb filter. To setup the gamma adjustment. To switch on/off the adaptive black. To switch on/off the blue stretch. 5.4.1 To setup the Y/C delay, you must enter the installation mode.
SVP 450 PLUS - SVD 500 PLUS 5.4.2 To switch on/off the Comb filter, you have to enter in installation mode. 5.4.4 To switch on/off the DYNAMIC BLACK, you must enter the installation mode. Press VID.S the following menu will appear: Press VID.S the following menu will appear: VIDEO SETUP VIDEO SETUP Y/C DELAY WHITE BALANCE COMB. FILTER Y/C DELAY GAMMA ADJ. WHITE BALANCE ADAPTIVE BLACK COMB. FILTER BLUE STRETCH GAMMA ADJ.
To change the values of contrast, brightness, colour, hue, peaking directly, you can use the following buttons. Press or CONTRAST, select the contrast adjustment. to change the value. Press or Press ESC Press Press or Press ESC BRIGHTNESS, select the brightness adjustment. to change the value. to exit. COLOUR, select the colour adjustment to change the value. to exit. Press Press Press Press ESC HUE, select the hue adjustment only for NTSC signals to change the value. to exit.
SVP 450 PLUS - SVD 500 PLUS 5.7 White balance WHITE BALANCE To select one of the set colour temperatures (3200°K,6500°K, 9300°K, USER BANK) for the projected images. 3200K 6200K 9300K USER FACTORY To select one of the colour temperatures, proceed as follows: press the button for a few seconds, the following menu will appear: VIDEO ADJ. ADJ. ADJ. ADJ. SET FACTORY SET: if you select this item, the system will utilize the preset manufacturer regulations.
SVP 450 PLUS - SVD 500 PLUS Press ENTER, the following menu will appear: WORK 08 LOAD COPY MOVE DEL BN MEMORY MANAGER NAME F HOR VER 01 02 03 04 05 06 07 Pal Upc . . . . . Pup 16/9 Nstc..... NstcUpc Vga 2 Vga 3 N W N N N N 31.2 --.31.2 15.7 31.4 35.1 37.6 50 --50 60 60 56 68 Modify bank name 5.8.1 How to enter the memory manager Use the arrow or to scroll the alphabet and the arrow or to skip at the next letter. After having written the correct label, press ENTER to confirm.
SVP 450 PLUS - SVD 500 PLUS Use the arrow or and the left arrow to select LOAD. Press ENTER to confirm, the following menu will appear: Use the arrow or to select un memory bank from 01 5.8.5 How to store a new input signal To store a new input signal in a memory bank press MEMO and you will enter the MEMORY MANAGER mode. WORK 08 LOAD The following menu will appear: COPY WORK 10 LOAD COPY MOVE DEL MEMORY MANAGER BN NAME F HOR VER 04 05 06 07 08 09 10 Pal Upc Vga 3 Pup 16/9 Nstc.....
SVP 450 PLUS - SVD 500 PLUS Press ENTER to confirm. The following message will appear: WORK 08 Copy from 05 to ? LOAD Use the arrow or to select a memory bank (from 01 to 25) where to copy the information and press ENTER to confirm. The following message will appear: COPY MOVE DEL Copy from 05 to 09 ? BN MEMORY MANAGER NAME F HOR VER 01 02 03 04 05 06 07 Pal Upc . . . . . Pup 16/9 Nstc..... NstcUpc Vga 2 Vga 3 N W N N N N 31.2 --.31.2 15.7 31.4 35.1 37.
SVP 450 PLUS - SVD 500 PLUS Press ENTER to delete the memory bank, the following message will appear: Press OPT. The following menu will appear: OPTIONS MENU Done OSD INSTALL. TYPE The cursor will return to the left of the menu. If the memory bank you are deleting is the one in use, it will be deleted and the first bank with the same input signal frequency will be loaded. POWER ON VCR STABILITY MEMORY MANAGER WORKING TIME 5.
SVP 450 PLUS - SVD 500 PLUS 5.12 Deflection POWER ON STAND BY Press DEF to enter the deflection adjustment mode. Now you can carry out all the adjustments necessary to align the green tube image to the screen centre. SWITCH ON Throughly read these instructions if you are not familiar with these adjustments To switch on or off the VCR stability, you must enter the installation mode. 5.12.
SVP 450 PLUS - SVD 500 PLUS Use the arrow or to change horizontal linearity. Use the arrow or to change vertical linearity. Press ENTER or EXIT to change function. Press ESC to exit. 5.12.5 Deflection pincushion top This funtion allows to change top and horizontal pincushion. 5.12.3 Deflection dimensions DEFL PIN TOP This function allows to change the dimensions of the raster. H. = 50 V. = 50 - PICTURE - Use the arrow or so that the top horizontal lines are straight.
Use the R,G,B, buttons to switch on or off the tubes. The CRT message: RGB indicates which tubes are switched on. Use the Rsel, Gsel, Bsel, buttons to select on which tube you wish to act. The ADJ message: R. indicates on which tube you are acting. Press ENTER or EXIT to change adjustment. Press ESC to exit. 5.13.1 Central convergence This function allows to overlap the blue and red images on the green one, at the centre of the screen. Press CONV. The following menu will appear: 5.13.
SVP 450 PLUS - SVD 500 PLUS 5.13.6 Horizontal keystone adjustment 5.13.8 Convergence borders This function allows to overlap the red and blue horizontal lines on the green ones. This function allows to adjust the image zones indicated by the crosses. + CONV KEY CRT : RGB ADJ : R . . CRT : RGB + ADJ / R . . BORDER H. = 50 V. = 60 V. = 50 Use the arrow or to set in line the horizontal lines of the image with the screen borders. Use the R,G,B, buttons to switch on or off the tubes.
SVP 450 PLUS - SVD 500 PLUS 5.17 How to store the convergence adjustments Upon pressing the ENTER button, you enter the corner adjustment menu, the folowing image will appear. + To store convergence, deflection, and zone adjustments press MEMO + CRT : RGB Thus entering the MEMORY MANAGER the following image will appear: ADJ / R . . WORK 08 ZONE H. = 50 V. = 60 LOAD + + COPY MOVE Press EXIT or ENTER to change. Press ESC to exit.
SVP 450 PLUS - SVD 500 PLUS - 6 TECHNICAL SPECIFICATIONS The video projector is set at factory for a 6500°K colour temperature. 6.1 Projection system 6.8 Automatic cut off - 3 picture tubes, 3 lenses - - Horizontal line system Lenses : Hybrid lenses (SVP 450 PLUS) High definition glass lenses (SVP 500 PLUS-HD) 6.9 Adjustments - 6.2 Projection tube The projector automatically performs the cut-off for the colour temperature stability at set intervals.
SVP 450 PLUS - SVD 500 PLUS By pressing any other key, the illumination counter is restarted. Batteries: - 4 1,5 Volt batteries, mod. UM4 E R03P 7.1 Flyback time - Horizontal 5,4 µs tip. - Vertical 500 µs tip. - R,G,B band width: 20 MHz, -3dB typical. - Standard video band width: 5.5 Mhz, -3dB typical - Contrast range: more than 100:1 - Warm up time (suggested): 20 minutes - 7.
SVP 450 PLUS - SVD 500 PLUS 7.8 Scart connector - Pin 5 Earth B Pin 7 Input B Pin 9 Earth G Pin 11 Input G Pin 13 Earth R Pin 15 Input R o C (S-VHS) Pin 17 Video Earth Pin 19 Video output Pin 20 Video input Pin 21 Screen Earth or common return 8 ELECTRICAL DATA Power consumption: 0.7 Vpp, termination 75 270W max (6W on stand-by) Line voltage range: 120-240Vac 50-60Hz 0.7 Vpp, termination 75 0.7 Vpp, termination 75 Fuse: T5A 9 MECHANICAL DATA 0.
SVP 450 PLUS - SVD 500 PLUS 12 TROUBLESHOOTING ON indicator Remote control indicator ENGLISH The LED lights on the rear panel shows the projector status.
SVP 450 PLUS - SVD 500 PLUS 13 ANWEISUNGEN AUF DEUTSCH 13.1Hinweis gemäß behördlicher Vorschriften ACHTUNG: ÖFFNEN SIE NICHT UND NEHMEN SIE NIEMALS DIE HAUBE DES PROJEKTORS AB WEIL DARUNTER GEFAHRLICHE HOCHSPANNUNGEN, BIS 33 KVOLT, ANLIEGEN. WENN ERFORDERLICH, RUFEN SIE IMMER EINEN TECHNIKER. Die in diesem Gerät entstehende Röntgenstrahlung ist ausreichend abgeschirmt. Beschleunigungsspannung maximal 33,5 KVolt.
• Due to the constant product development, specifications and design might be subject to change without notice. • A causa dello sviluppo continuo del prodotto, specifiche e progetto potrebbero subire modifiche senza preavviso. SIM2 Multimedia S.p.a. • V.le Lino Zanussi, 11 • I-33170 Pordenone • Phone +39.434.383.253-256 • Fax +39.434.383260-261 • http://www.sim2.it • e-mail: info@sim2.it cod. 46.9220.
