USER AND INSTALLATION MANUAL MANUALE D’USO E INSTALLAZIONE GEBRAUCHS-UND INSTALLATIONSANLEITUNG VIDEO PROJECTOR MANUAL DE USO E INSTALACIÓN PROJECTOR SVD 800 HD
INDEX 1- WARNINGS ......................................................................................... Page 3 1.1 Safety and Regulations ............................................................. 4 2- GENERAL INFORMATION ................................................................. 2.1 Projector identification ............................................................... 2.2 Power cabling ............................................................................ 2.3 Servicing ............
SVD 800 HD 4.8 4.9 4.10 4.11 Lens focus adjustment .............................................................. Page 23 Mechanical centering of the tubes ............................................ 24 Correct screen viewing (deflections inversion) .......................... 24 Convergence adjustment .......................................................... 24 5- THE COMPLETE FUNCTION RC3000 REMOTE CONTROL ........... 5.1 Complete function RC3000 remote control ............................... 5.
1 - WARNINGS CAUTION ELECTRIC SHOCK HAZARD DO NOT OPEN ! TO REDUCE THE RISK OF ELECTRIC SHOCK, DISCONNECT THE POWER SUPPLY CABLE BEFORE OPENING THE EQUIPMENT There are no parts inside the projector that need adjusting by the user. Qualified technicians must be called to perform extraordinary maintenance and adjustments. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
SVD 800 HD MAINS POWER 2.1 Projector identification Mains power: 120-240Vac 48-62Hz +6%-10% Max absorbed current: 4.2A The model and serial number are located on the projector’s rear label Fig. 1. 1.1 Safety and Regulations A) Safety - conform to: EN60950: Equipment for information technology including electric office equipment. Safety.
- If the projector is not used for long periods of time or during storms, unplug the projector temporarily from the mains to avoid damaging the projector caused by lightning or temporary overcurrents. 2.3 Servicing Servicing must be carried out by qualified technicians. Do not attempt to service the projector without the proper technical knowledge. Opening the projector can expose personnel to potential hazards: high voltage and electric shock.
SVD 800 HD - Avoid touching the lenses with your fingers, which would leave marks. Clean them as you would any ordinary photographic lens since they have an anti-reflection coating (use special lens cleaning paper or special photographic lens cloth with care). 2.7 Packing the projector For the best protection pack the projector as it was originally packed at the factory. For air freight shipping use metal or plastic straps to secure the box.
• 21- Led pilot light (red=stand by - green=on). THE FOLLOWING FUNCTIONS ARE ON THE PANEL: 22- LED, blinks (red) when signal from the remote control is received. 1- Power switch. 23- Remote control signal receiver (rear). 24- Remote control signal receiver (front). 2- Fuse holder. The fuse type is 10A, T-H delayed. Attention: For continued protection against the risk of fire, replace only with one of the same type and rating. 3- Mains power connector.
SVD 800 HD 3 USER REMOTE CONTROL RC 3100 RC 3100 is the User Remote Control for normal programme selection and analogue adjustments (once the projector is installed). The projector is controlled by the infrared ray remote control (I.R.) whose maximum range is approximately 10 metres with new batteries. The following figure describes the functions of the buttons on the User Remote Control. To select the signal input directly. Also used to turn the projector ON.
3.1 Batteries - Press any button to eliminate the initial screen and to see the image immediately after having switched the projector on in the case, for instance, it has already been adjusted and warming up is unnecessary. - Warm-up time can be modified and/or excluded, see par. 3.21 OSD OPTIONS page 14. Handling the remote control and batteries: - Avoid exposing the remote control to heat and humidity. - When not using the remote control for a long period of time, remove the batteries.
SVD 800 HD 3.6 Screen format selection 3.8 Information (INFO) To select the correct screen format: (NORMAL, SMALL, LETTER BOX, CINEMA, WIDE). The INFO menu displays information on a current input signal. Press the button. One of the previous screen formats will appear (for instance 16/9). - GENERAL INFORMATION INPUT HORIZ. FREQ. VERT. FREQ. VIDEO STANDARD COMB FILTER UP CONVERTER BANK NAME BANK LOADED 1/2 - VIDEO1 15.66 KHZ 50 HZ PAL ON OFF PAL 01 Fig. 11 Press INFO again.
The COMB filter increases separation between luminance and chrominance, avoiding colour overlapping, we recommend ON 3.13 Video Menu Press ••• . The MAIN MENU appears. Press Press or . Y-C DELAY appears or to adjust, EXIT - MAIN MENU - VIDEO MENU OPTIONS INSTALL. MENU - QSD MANAGER STD DETECT COMB FILTER Y-C DELAY Fig. 13 AUTO ON 05 PAL Press or . Select VIDEO MENU. Press ENTER. The VIDEO MENU appears Fig. 17 The value is correct when the colour bars are displayed and they do not overlap.
SVD 800 HD Press 3.15Input Settings or - VIDEO MENU - . TLV SYNC ON appears. - INPUT SETTINGS - QSD MANAGER UPC MANAGER INPUT SETTINGS BLANKING EHT NOISE RED. WHITE MENU CLAMP POS TLV SYNC MANUAL 50 OFF Fig. 23 Press MEMO, ENTER, EXIT. Fig. 20 CLAMP POS 3.16 Blanking With this menu you can select the position of the CLAMP impulse on the external video signal.
Press or . Adjust to eliminate interference. Press MEMO , ENTER, EXIT. 3.19 OPTIONS Press ••• . The MAIN MENU appears Press or . Select OPTIONS, ENTER Note: Adjust when the projector is synchronised and when there are either external or internal white patterns. - MAIN MENU - EHT NOISE REDUCTION CRT = R G B VALUE = VIDEO MENU OPTIONS INSTALL. MENU XX Fig. 30 Fig. 27 Press or . Select MISCELLANEOUS, ENTER 3.
SVD 800 HD The daily ENABLING item enables the projector to turn on and off automatically each day when ON is set. 3.21 OSD OPTIONS Note: The values on the right are only an example. This menu allows you to set the MESSAGE TIME, MENU TIME, ON SCREEN DISPLAY of the image, the colour of the On Screen Display and WARM-UP time. Press or Press or Press or . Select the item you wish to set and press ENTER . .
3.22 LOGO Press or . Select LOGO, ENTER to enable or disable, EXIT to exit. - MISCELLANEOUS - TIMER FUNCTIONS WARKING TIME OSD OPTIONS LOGO SIM2 Fig. 38 3.23 Installation menu THE ADJUSTMENTS DESCRIBED IN THIS PARAGRAPH MUST BE CARRIED OUT BY QUALIFIED PERSONNEL. ANY ADJUSTMENTS INCORRECTLY DONE CAN CAUSE A DETERIORATION IN PICTURE QUALITY. 3.
SVD 800 HD 4 INSTALLATION 4.2 Removing the cover 4.1 Installation procedure 4.2.1 Removing the top cover In order to obtain the best performance from the projector, the following procedure has to be followed carefully and carried out by a technician. Loosen the 2 securing screws (A) and lift the cover up. A Note: The projector is factory-set for front ceiling projection with a 90” screen, 4/3 format and a projector-screen distance of 284 cm., see Fig. 49, reference (D), page 19. 1.
4.2.2 Removing the front panel SCREEN Unscrew the two screws (D) on the left and right of the front panel. Unscrew the three screws (E) on the bottom and take the panel off. The position of the screws is shown by the arrows in Fig. 42. B SCREEN CENTRE 14° A D Fig. 43 D The distance between the projector and the screen (depending on screen dimensions), is shown in the following table.
SVD 800 HD 4.3.3 Desktop rear projection - For rear projection we recommend installing the projector with the axis of the green lens orthogonal to the screen plane; pay attention that the green lens be centered with respect to the screen (see: par. 4.6, Projector Centering page 23). - Example: Suppose we have a 105” screen diagonal. 100” is the nearest value in the table. The A/Width ratio is equal to 299/203.2=1.471 A105” screen diagonal is 213.3 wide So, the value of A is: 1.471x213.3=313.7 cm.
Fix the bracket, included in the pack, to the ceiling with the four screws supplied. H R F N T 93 O Attention: The bracket must be fixed properly and be absolutely parallel with the screen 44 N T 0 R F O = BRACKET Fig. 48 = SC RE EN Note: the tilting angle between the base plane of the projector and the lenses’ axis should be 14°. OBSERVE PARALLELISM Fig. 46 D Put the projector on a table in the vertical position (sideways) N.B.: Take the two front feet off.
SVD 800 HD Attention: Correct use of the spacers, as shown in the tables, is of paramount importance for perfect focus uniformity. 4.3.5 Ceiling rear projection Rear projection installation is done by hanging the projector on the ceiling and following the instructions given for front installation. 4.5.1. Spacers changing To change the spacers first of all remove the top cover and front panel. Now slightly loosen the 4 screws (A) for each tube, change the spacers (B) Fig.
90" 4.5.2 Spacers table BLUE Front view of the CRT. 1 0,2 GREEN 1 1 0,5 0,2 RED 1 1 0,2 0,5 1 0,2 12° 0 0,3 1 0,3 SPACERS 0 1 1 0,5 0,3 0,2 14° SPACERS 0 0,3 0 1 1 0,3 0,5 0,2 1 0,3 0 0,3 0 0 0,3 0 1 0,5 0,2 2 1 0,5 0,2 1 0,5 0,2 2 1 0,5 0,2 0 0,3 0 0 0,3 0 CRT LENS 18° Fig.
SVD 800 HD 150" BLUE 0,5 0,2 250" GREEN 1 0,5 0,2 RED 0,5 0,2 1 BLUE 0,5 0,2 12° GREEN 0,5 0,2 0,5 0,3 0,3 0,2 RED 0,3 0,2 0,5 0,3 0,5 0,2 0 0,3 0,2 0,3 0,2 0,5 0,3 0,5 0,2 12° 0 0,2 0 0 0,2 0 0,2 0,3 0,5 0,3 1 0,5 0,3 0,5 0,3 1 0,5 0,3 0,5 0,2 0,5 0,3 0,3 0,2 14° 0 14° 0 0,2 0 0 0,2 0 0,2 0,3 0 0 0,3 0,2 1 1 0,2 1 1 1 0,2 1 0,5 0,3 1 0,5 0,2 0,5 0,2 1 0,5 0,3 0,2 0,3 0 0 0,3 0,2 0,3 0,3 0,3 0 0 0 0,5 0,3 0,2 0,3 0,2 0 0 0 0,5
4.6 Projector centering 4.8 Lens focus adjustment The first step towards a good installation is centering the projector with respect to the screen. This can be done using two pieces of equally long cord, as illustrated in the following figure: Each lens must be focused individually with the tubes on, one at a time and following this procedure: 1. Select the HATCH test pattern by pressing the TEST button on the remote control. An external pattern signal can be used if you prefer. SCREEN 2.
SVD 800 HD 4.9 Mechanical centering of the tubes A For an installation different to factory setting (90”) the mechanical centering of the red and blue tubes needs to be adjusted. Select the CROSS HATCH signal with the remote control. Looking at the following figure, unscrew (only 2 turns!) the screws (A-B-C-D) of the red tube. B Fig. 57 C 3. D If necessary modify the setting as shown in the following figures.
5 THE COMPLETE FUNCTION RC3000 REMOTE CONTROL 5.1 Complete function RC3000 remote control via cable directly to the video projector’s IR input so as to avoid any technical problems. N.B.: (The cable is supplied with the projector. Standard length is 8m.). The following pages explain the functions of the buttons on the RC3000 remote control. There are two remote controls for the video projector.
SVD 800 HD 5.2 Batteries 5.4 Turning the projector on Handling the remote control and batteries: Press the mains switch; the red stand-by LED on the rear panel turns on. - Avoid exposing the remote control to heat and humidity Press - When not using the remote control for a long period of time, remove the batteries. , or one of the buttons from 1÷9. The red LED becomes green ON.
Press Press . or HUE, selects the hue setting, only for NTSC signals to change the value. Press MEMO if you wish to store all the settings when one of the functions is displayed. Press ESC to exit. TIN Press Press . or 50 Fig. 68 all the values stored in the N.B.: If your press displayed signal bank are recalled. PEAK, selects the peaking setting to change the value. DET 100 Fig. 69 5.6 Test patterns To select a test pattern press TEST. The following eight patterns will appear in sequence.
SVD 800 HD Press VIDEO MENU or . Select EDIT PRESET. Press VID.S. the VIDEO MENU appears. - WHITE MENU - To adjust the various sub menus see: par. 3.13, VIDEO MENU, page 11. - SET SET SET SET SET EDIT TO 3200°K TO 6500°K TO 9300°K TO USER TO BANK PRESET Fig. 74 - MAIN MENU - VIDEO MENU OPTIONS INSTALL. MENU Press ENTER. WHITE BALANCE 6500 °K appears - WHITE BALANCE 6500°K Fig. 71 5.7 White balance To select one of the set colour temperatures (3200°K, 6500°K, 9300°K, USER, BANK) see par. 3.
(F) indicates which ratio flag was stored by the user during the adjustments. 5.8.2 How to insert a label Press The horizontal and vertical frequencies are measured by the projector and stored in the relative memory bank each time you save an adjustment. When the projector is switched on the last memory bank used is recalled. or . Select LABEL - MEMORY MANAGER BANK 01 SIGNAL NAME PAL LOAD COPY 5.8.1 How to enter the memory manager MOVE DEL Enter the SERVICE MODE, see par. 3.24 page 15. Press OPT.
SVD 800 HD Press or Enter the label; see par. 5.8.2 page 29. Press ENTER and the following will appear: . Select the right ratio from among: N (Normal), S (Small), L (Letter box), C (Cinema), W (Wide). Press ENTER to confirm. The following message will appear under the table: EDIT ASPECT RATIO. NEW INPUT SIGNAL CONFIRM NEW NAME: XXXXXXXX 5.8.
5.8.7 Copy (COPY) 5.8.8 MOVE (MOVE) This function allows you to copy a memory location containing settings in another location. This function allows you to move a memory bank to another position on the list. Press Press or . Select COPY, ENTER. or . Select MOVE. - MEMORY MANAGER BANK 01 SIGNAL NAME PAL - MEMORY MANAGER BANK 01 SIGNAL NAME PAL LOAD LOAD COPY MOVE DEL N 00 01 02 03 04 05 06 07 08 09 HOR VER F LABEL 33.7 15.6 15.7 31.5 31.5 31.2 48.4 64.3 71.7 44.
SVD 800 HD Press or . Select the installation type. Press ENTER to confirm. 5.8.9 DELETE (DEL) This function allows you to delete a memory bank. Press or . Select the DEL function. - INSTALL. TYPE - MEMORY MANAGER BANK 01 SIGNAL NAME PAL LOAD COPY MOVE DEL N 00 01 02 03 04 05 06 07 08 09 - HOR VER F LABEL 33.7 15.6 15.7 31.5 31.5 31.2 48.4 64.3 71.7 44.
N.B.: In the case of ceiling to floor installations or vice versa, press or to position V. VALUE=30, adjust P3 (LIN. PRESET) on PC 098 (vertical def.) for a good vertical linearity, press or for a fine adjustment. Use this function to centre the external signal image with respect to the raster. This adjustment is common to the three colours R.G.B. Press CONV Press or to centre the image on the screen. PHASE V L ER IN E T A IC R A IT L Y CRT = R G B ICAL Y ARIT VERT LINE H. VALUE = XX Fig. 106 Fig.
SVD 800 HD 5.11.6 BOW Press or , 5.11.9 ZONES or to adjust. This function adjusts the red zones after having adjusted convergence and when the red and green lines converge. BOW Press ZONE. The ZONE menu appears. CRT = R G B ADJ = R - - H. V. VALUE VALUE = = CRT R G B XX XX Fig. 112 - H. V. ZONE SHIFT FINE VALUE VALUE = = - ADJ R - - XX XX 5.11.7 KEYSTONE Press or , or Fig. 115 to adjust. This menu changes according to the zone you are adjusting.
5.12 How to reset the adjustments (RESET) Note: Resetting means setting all adjustment values at 50 that corresponds to zero. Starting from this value you can adjust up to 100 or down to 0. To reset adjustments read the following instructions carefully. If you press the RESET button when you are in the convergence setups (CONV), you will reset the convergence parameters and those of the zones of the three colours R.G.B..
SVD 800 HD 6 TECHNICAL SPECIFICATIONS 6.8 Automatic cut off - 6.1 Optical data 6.9 Adjustments Projection system - 3 projection tubes, 3 lenses - Horizontal line system - 6.2 Projection tube - 7” monochrome tube, high brightness, liquid cooling, air lens coupling, electrostatic focusing. - The external red and blue tubes are mechanically rotated. The projector automatically carries out controls for better colour temperature stability at set intervals.
7 DISPLAY PERFORMANCE 7.4 User remote control mod. RC3100 7.1 Flyback time Operating mode: - Horizontal 2.4 µs typ. - Vertical 150 µs typ. - R,G,B video bandwidth: 75MHz, -3dB typical Functions: - Standard video bandwidth: 5.5Mhz, -3dB tipical All adjustments can be modified using the remote control, some can be directly accessed with a key: - Warm up time (suggested): 10 minutes Wireless (max operating distance:10m/30ft) - Turning ON/OFF 7.
SVD 800 HD 7.7 Input synchro 8 ELECTRICAL DATA H, H/V sync 75 Ohm termination a) Horizontal sync or composite sync 0.3-5Vpp, positive or negative Input: 500W max (12W on stand-by) Voltage: 120-240Vac 50-60Hz with power factor correction Fuse: 10A TH b) Vertical sync: 0.3-5Vpp, positive or negative 9 Mechanical data 7.9 Video inputs Dimensions: CVBS 1 BNC composite video input connector, 1Vpp, 75 Ohm termination, negative sync.
13 PIN ASSIGNMENT S VIDEO connector (4pin, mini-DIN) RS-422A connector (female 9 pin D-sub) Crominance Luminance 5 9 GND GND No. pin 1 2 3 4 5 6 7 8 9 VGA input DB-15 female connector 5 4 10 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 3 9 14 2 8 13 1 7 12 4 6 11 Red Green Blue Not used Not used GND GND GND Not used GND Not used Not used H / HV V Not used 3 8 2 7 1 6 Signal GND Not used Not used TX TX Do not use Not used RX RX RS 232 compatible connector (only for short distances) No.
SVD 800 HD 14 TROUBLESHOOTING The pilot lights on the rear panel show the projector status. ON indicator Remote control indicator PILOT LIGHT MEANING Red light Stand-by mode Green light Normal operation Blincking light The projector is receiving commands from the remote control In case of mulfunctioning check the following table before asking for service help.
15 FRENCH INSTRUCTION 15.1 Procedure d’installation au plafond 15.2 Projection frontale avec fixation du projecteur au plafond ATTENTION: SIM 2 Multimedia décline toute responsabilité pour les dommages matériels et humains causés par une installation mécanique, au plafond, erronée ou négligée, toutes les opérations doivent être effectuées par un technicien qualifié.
SVD 800 HD Retourner le projecteur et le fixer au plafond au moyen des deux crochets. Incliner le projecteur de manière à centrer l’image verticale et visser les deux vis de fixation (H). Note: Introduire les rondelles arrondies spéciales entre le crochet et les vis de fixation. Pour une installation correctement effectuée, la partie concave de la rondelle doit être orientée vers la patte de fixation. Pour une installation faite en toute sécurité, n’utiliser que le kit de fixation fourni dans l’emballage.
