RTX 45-55 USE AND INSTALLATION MANUAL ENGLISH
IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTROCUTION DO NOT OPEN ! Make sure not to overload the socket or any extension cord. For the DigiOptical Image Processor only use the power supply provided or in any case a power supply approved by SIM2. • Pay attention to the cables. Arrange the cables so that they do not constitute an obstacle. Also, keep them out of the reach of children. Install the units as close as possible to the wall socket.
TABLE OF CONTENTS INTRODUCTION ....................................................................................................................... 4 1 INSTALLATION.............................................................................................. 6 CONNECTING THE TWO UNITS .............................................................................................. 6 CONNECTING THE VIDEO SOURCES .................................................................................... 7 Video ..
INTRODUCTION Thank you for choosing the GrandCinema RTX system from SIM2! The RTX system integrates the signal processing ability of the DigiOptical Image Processor with the faithful reproduction of a DLP™ technology Display, putting the two units in communication with each other by means of an optical fibre connection.
The DigiOptical Image Processor, ideally placed near the sources, can acquire and process a wide range of video signals, in order to send them to the Display by means of the optical fibre connection. All adjustments relevant to the image can be performed with the remote control with the aid of the On Screen Display; alternatively, the unit can be controlled by a domestic automation system through the serial port.
1 INSTALLATION CONNECTING THE TWO UNITS supply. Connect the cable of the power supply to the POWER input located on the rear panel (Fig. 4). Only use the power supply provided with the system or a power supply approved by SIM2. The RTX system of SIM2 comprises the elements listed below (Fig.
for even the most demanding installations. During installation of the optical fibre cable: • Take particular care in handling the fibres: only handle the cable ahead of the unravelling point (Fig. 3). Only pull on the cable, not on the fibres or connectors. • Only remove the protection plug covering the ferrula when inserting in the connector: if it should come in contact with other bodies it could be damaged and rendered unusable.
11 DVI-D OPTICAL FIBER LINK CONTROL (RS 232) DV 11 I- D - 9 10 Computer T N OE D US 3 GRAPHICS RGB 2 1 10 C T ON RO L (R S 23 2) R SE S AS 9 8 T CL 3 V UC OD PR A 1L HV Cb B/ 7 GR Y G/ AP HI CS RG B 1 COMPONENT / RGBS 2 H/ 5 6 7 8 Computer Domestic automation device V Cr R/ V H H/ Cb B/ V 3 4 1 2 Y G/ 6 HV H/ S-VIDEO B/ VIDEO T V EN ON Y G/ POWER HV H/ Cr HDTV receiver Videogame console Computer Cr R/ 5 Cb CO / B RG S MP R/ Television
The video signals applicable to this input can have scanning frequencies of 15 kHz (standard resolution video), 32 kHz or higher (progressive scanning video and high definition video). Sometimes it is possible to choose whether to obtain a progressive instead of interlaced signal from the source.
2 USE TURNING ON AND OFF The RTX system consists of two units (DigiOptical Image Processor and Display), the first of which is also the system control centre. The DigiOptical Image Processor sends commands to the Display and receives information about its operation from it, in addition to the commands sent by the user.
Do not turn the power switches of the units to the “O” position and do not disconnect the power supply cables immediately after putting the system in stand-by mode, but wait at least one minute. This is to allow the fans in the Display unit to cool the lamp. KEYPAD The keypad on the back of the Display comprises eight keys that allow complete control of the device even in absence of the remote control. MENU These allow navigating in the menus of the On Screen Display and parameter adjustments.
STAND-BY Puts the system in stand-by mode. KEYS 0-9 They turn on the projector from stand-by mode and allow the direct selection of inputs. INPUT Displays the Input Selection menu. ESCAPE Deactivates the On Screen Display. Not active in this model. These allow navigating inside the On Screen Display and adjusting the parameters. recalls the quick menus. MENU Activates the On Screen Display and allows navigating though its pages.
by pressing the ESC key, or when the time allowed for displaying the on-screen menu has lapsed (set in the Set-up Menu). Inputs 5, 6, 7 and 8 can receive RGB and YCrCb signals, at 15 kHz, 32 kHz or higher. The association between the input and the type of signal is made from the pull-down menu that appears on the right of the < symbol after pressing the < key (Fig. 12b).
SHARPNESS MODE This allows you to select the type of processing associated with the sharpness adjustment. In the case of a progressive or interlaced video signal VIDEO mode is advisable; with PC graphic signals, it is more appropriate to use GRAPHIC. It is possible to select a different aspect for each of the sources: it will be automatically recalled when the source is recalled.
Generally, the HIGH value is more suitable for displaying graphic images, MEDIUM and LOW for video images. SET-UP This menu contains less frequently used adjustments that can be of help during installation (e.g. selecting the language for the On Screen Display or the display of Test Patterns). We recommend that only expert users make these adjustments since there is a risk of obtaining results that could lower the quality of the projected image.
Out of Range specifications (e.g. a QXGA graphic signal) or when a signal is being sent to a given input not compatible with it (e.g. sending a progressive single to an input after having set it to YCrCb 15kHz). This message appears when the vertical/horizontal resolution or the frequency of the input signal exceeds the system MAINTENANCE AND TROUBLESHOOTING • Check the integrity of the cables used to connect the DigiOptical Image Processor to the various sources.
receivers located on the front panel of the DigiOptical Image Processor and the front of the Display. • Make sure the infrared receivers located on the front panel of the DigiOptical Image Processor and at the front of the Display are not illuminated by intense light sources.
3 ADDITIONAL INFORMATION TECHNICAL SPECIFICATIONS DISPLAY OPTICS Optical system: DMD™ panel: Projection lens: Colour wheel: Lamp: Image dimensions: Brightness: GENERAL a single DMD™ panel, sealed against dust TI HD2 0.8" 12° Dark Metal - 1280x720 pixels (aspect ratio 16:9) UltraWide angle F/2.4 6 segments (RGBRGB) - 9000 rpm max 120 W UHP - 6,000 hours* 45": 996x560 mm (39.
Colour temperature: Control: Outputs: sequence conversion from 5000 to 9300 °K (three pre-set values and one customisable) infrared ray remote control, RS232 serial (DB9 connector, female) 2 12-V jack connector outputs (1 active with system turned on, 1 active with 16:9 aspect ratio selected) Consumption: Dimensions: Weight (approx.): Operating Temp.: Transport Temp.: Warehouse Temp.
DIMENSIONS DISPLAY 1227,8 mm - 48,34" 996,2 mm - 39,22" 368,6 mm 14,51" 1108 mm - 43,62" 560,5 mm - 22,07" 1108 mm - 43,62" RTX 45” 956,3 mm - 37,65" RTX 55” 235 mm 9,25" 420,3 mm 16,54" 1218 mm - 47,95" 684,9 mm - 26,96" 1218 mm - 47,95" 1494,2 mm - 58,82" 1217,6 mm - 47,93" 1188 mm - 46,78" 245 mm 9,64" Unit of measure: mm Scale 1:20 DIGIOPTICAL IMAGE PROCESSOR Unit of measure: mm Scale 1:5 20
STRUCTURE OF THE ON SCREEN MENUS Picture Brightness Contrast Color Tint Sharpness Filter Cinema Mode Video Type Video • S-Video [NTSC] YCrCb15kHz RGBS 15kHz Video • S-Video [PAL, SECAM] RGBS 32kHz RGB Grafico DVI-D 32kHz Brightness Contrast Color Sharpness Filter Cinema Mode Video Type Brightness Contrast Sharpness Sharpness Mode Brightness Contrast Color Tint Sharpness Sharpness Mode Image Video • S-Video Aspect Color Temperature Gamma Correction Position Y/C Delay Magnification Aspect Color Te
