STRIDER ST1500 The dream PSU for computer enthusiasts 1500W continuous and 1600W peak power 100% modular cables with cable bag Efficiency 85%~88% at 20%~100% loading with 80 PLUS Silver certification Class-leading eight +12V rails with 110A (Peak up to 120A) 1500W continuous power output with 40C operating temperature Strict ±3% voltage regulation Silent running 135mm fan with 19dBA minimum Japanese main capacitors Four PCI-E 8pin, eight PCI-E 6pin, and twelve SATA connectors support Support ATX 12V 2.
SilverStone STRIDER ST1500 ATX12V / EPS 12V Switching Power Supply With Active PFC PS/2 1500W This specification describes the requirements of 1500Watts switching power supply with an stretch form-factor and EPS12V, +5V standby voltage, remote on/off control, full range line input capability and forced air cooling characteristics. 1. AC INPUT 1-1. AC input requirements The input voltage, current, and frequency requirements for continuous operation are stated below.
ŔŕœŊŅņœġŔŕIJĶıı 2-1. DC voltage regulation MIN NOM MAX Units Tolerance +3.3V +3.20 +3.30 +3.39 Vms +/-3% +5V +4.85 +5.00 +5.15 Vms +/-3% +12V1,2,3,4,5,6,7,8 +11.64 +12.00 +12.36 Vms +/-3% -12V -10.8 -12.20 -13.20 Vms +/-10% +5VSB +4.75 +5.00 +5.25 Vms +5/-5% Peak Unit Parameter 2-2. Load ranges Load Range Parameter Min Nom. Max +3.3V 0.8 - 40 - Amps +5V 0.5 - 40 - Amps +12V1 0.1 - 25 30 Amps +12V2 0.1 - 25 30 Amps +12V3 0.
1.Maximum continuous total DC output power should not exceed 1500W. 2.Maximum c.ontinuous combined load on +3.3 VDC and +5 VDC outputs shall not exceed 280W. 3.Maximum peak total DC output power should not exceed 1600 W. 4.Peak power and current loading shall be supported for a minimum of 12 second. 5.Maximum combined current for the 12 V outputs shall be 110A. 6.Peak current for the combined 12V outputs shall be 120A. 2-3. Output Ripple 2-3-1. Ripple regulation Parameter Ripple&Noise Unit +3.
ŔŕœŊŅņœġŔŕIJĶıı 2-3-2. Definition The ripple voltage of the outputs shall be measured at the pins of the output connector when terminated in the load impedance specified in figure 1. Ripple and noise are measured at the connectors with a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor to simulate system loading. Ripple shall be measured under any condition of line voltage, output load, line frequency, operation temperature. 2-3-3.
3. PROTECTION 3-1. Over current protection The power supply shall have current limit to prevent the +3.3 V, +5 V, and +12 V outputs from exceeding the values shown in Table 28. If the current limits are exceeded the power supply shall shutdown and latch off. The latch will be cleared by toggling the PSON# signal or by an AC power interruption. The power supply shall not be damaged from repeated power cycling in this condition.
ŔŕœŊŅņœġŔŕIJĶıı 3-4. Short circuit An output short circuit is defined as any output impedance of less than 0.1 ohms.The power supply shall shut down and latch off for shorting the +3.3 VDC,+5 VDC,or+12 VDC rails to return or any other rail. Shorts between main output rails and +5VSB shall not cause any damage to the power supply. The power supply shall either shut down and latch off or fold back for shorting the negative rails.
4-2. Hold up time When the power loss its input power, it shall maintain 17ms in regulation limit at normal input voltage. (AC:115V/60Hz or 230V/50Hz) 5. ENVIRONMENT 5-1. Operation Temperature Relative Humidity 0 to 40 10 to 85%, non-condensing 5-2. Shipping and Storage Temperature Relative Humidity -40 to 70 5 to 90%, non-condensing 5.3 Altitude Operating 10,000FT max Storage 50,000FT max 6. SAFETY 6-1. Underwriters Laboratory (UL) recognition. The power supply designed to meet UL 6-2.
ŔŕœŊŅņœġŔŕIJĶıı 7. ELECTROMAGNETIC COMPATIBILITY (EMC) 7-1. IEC 1000-4-2 ESD LEVEL X20KV4. 7-2. IEC 1000-4-3 radiated electrical field requirement. 7-3. IEC 1000-4-4 BURST. 7-4. IEC 1000-4-5 surge Voltages. 7-5. EN61000-3-2 harmonic current emissions.
9-2. Connectors(Pin definition) M/B 24PIN connector Signal Pin Orange +3.3V 13 Orange +3.3Vsense 13 Blue -12VDC Black Pin Signal 1 +3.3V Orange 14 2 +3.3V +3.3V COM 15 3 COM COM Green PS-ON 16 4 +5VDC +5VDC Black COM 17 5 COM COM Black COM 18 6 +5VDC +5VDC Black COM 19 7 COM COM White N/C 20 8 PWRGOOD PWRGOOD Red +5VDC 21 9 +5Vsb +5Vsb Red +5VDC 22 10 +12V3 Yellow Red +5Vsense 22 Red +5VDC 23 11 +12V3 +12V3 Black COM 24 12 +3.
ŔŕœŊŅņœġŔŕIJĶıı 4PIN peripheral connector (HDD) 4PIN floppy connector (FDD) Signal Pin Pin Signal Yellow +12V3/4 1 1 +5VDC Red Black COM 2 2 COM Black Black COM 3 3 COM Black Red +5VDC 4 4 +12V3/4 Yellow SATA connector Signal Pin Orange +3.
