SPECIFICATION SFX-L Form Factor SST-SX1000-LPT 1000W Switching Power Supply With Active PFC 80Plus Platinum This specification defines ATX multiple output switching power supply. The parameters of this supply are defined in this specification for Family using. This specification defines max continuous output at 1000W with 100 to 240Vac input, power supply with five outputs; +3.3V, +5V, +12V, -12V and +5VSB. The +5V standby voltage, remote on/off control, full range line input capability.
2. DC Output characteristics: 2.1 Output voltage regulation Requirements: The power supply output voltage must stay within the following voltage limits shown in Table2 when operating at steady state. Table2 Parameter Range Min Nom. Max Unit +3.3V ±3% +3.20 +3.30 +3.39 Volts +5V ±3% +4.85 +5.0 +5.15 Volts +12V ±3% +11.64 +12.0 +12.36 Volts -12V ±10% -10.8 -12.0 -13.2 Volts +5VSb ±5% +4.75 +5.0 +5.25 Volts 2.
NOTES: 1. For example, for a rated +5 VDC output of 14A, the transient step would be 30% x 14 A = 4.2 A. 2.Output voltages should remin within the remain within the regulation limits of Section 2.1, and the power supply should stable when subjected to load transients per Table 3. from any steady state load, including any or all of the following conditions: 3. Simultaneous load steps on the +12 VDC, +5 VDC, and +3.3 VDC outputs (all steps occurring in the same direction) 4.
2.5 Efficiency: 2.5.1 In the 115Vac/60Hz input voltage the power supply efficiency is more than 94%. Table6 Load Efficiency(%) Power Factor 10% 20% 50% 100% -90 92 89 -->0.95 -- Note: There is a 1% tolerance in mass production 2.5.2 ERP 5VSB Efficiency +5VSB LOAD Table7 Efficiency target (both 110V and 230V input) 3A 75% 1.5A 75% 1A 75% 0.55A 75% 90mA 55% 45mA 45% 2.6 Remote on/off control When the logic level "PS-ON" is low, the DC outputs are to be enabled.
3.Environment: 3.1 Operation temperature: Table9 Temperature Relative Humidity 3.2 Shipping and Storage: 0 to 50℃ ℃ 5% to 90%,on- condensing Table10 Temperature Relative Humidity 3.3 Altitude: -40℃∼70℃ 5% to 95%,non - condensing Table11 Opera ng ≤2000m Storage ≤3000m 3.4 Cooling mode: Forced air cooling. 3.5 Random Vibration: Non-operating 0.01 g²/Hz at 5 Hz, sloping to 0.02 g²/Hz at 20 Hz, and maintaining 0.02 g²/Hz from 20 Hz to 500 Hz. The area under the PSD curve is 3.13 grams.
4.2 Over voltage protection: Table12 Output voltage protecƟon point Min Nom Max 3.76 4.2 4.3 5.74 6.3 7.0 13.4 15.0 15.6 5.74 6.3 7.0 Output +3.3V +5V +12V +5vsb Unit V V V V 4.3 Short circuit protection: An output short circuit is defined as any output impedance of less than 0.1 ohms. The power supply shall shut down and latch off for shorting the +3.3 VDC, +5 VDC,or+12VDC rails to return or any other rail. Shorts between main output rails and +5VSB shall not cause any damage to the power supply.
5. Power Supply Timing 5.1 Signal timing drawing Figure 2 is a reference for signal timing for main power connector signals and rails. Figure 2 Table14 Parameter T0 T1 T2 T3 T4 T5 T6 Description AC power on time Power-on time Rise time PWR_OK delay PWR_OK rise time AC loss to PWR_OK hold-up time PWR_OK inactive to DC loss delay Required <2s < 200ms 0.
6. SAFETY: The power supply designed to meet IEC 62368-1. 6.1 Electrical strength: Gradually increased from 0V to 1500V is applied in the AC line and the casing, and then keep for 1 minutes, the insulation should not breakdown; if the current increases rapidly due to the test voltage and gets out of the way, that is to limit the current insulation, insulation breakdown that has occurred; corona discharge or flashover is not a single moment that is the breakdown of insulation. 6.
9. POWER SUPPLY CONNECTOR OVERUSE DEFINITION EN Power supply connector overuse definition A single PCIe 8pin cable and connector’s maximum current rating is 12.5A, which is 150W (+12V x 12.5A). So SilverStone’s warranty will not cover damages or malfunction resulting from the use of a graphics card or expansion card with a single PCIe 8pin connector that exceeds standard 225W total power draw (150W from PCIe 8pin connector + 75W from PCIe motherboard slot).
FR Définition de l'utilisation excessive du connecteur d'alimentation électrique Le courant nominal maximum d'un câble et d'un connecteur PCIe 8 broches unique est de 12,5 A, ce qui correspond à 150 W (+12 V x 12,5 A).
JP 電力供給コネクタの使用限度超過に関する説明 単一のPCIe 8ピンケーブルおよびコネクタの最大定格電流は12.5A で150W (+12V x 12.5A)となります。それで定格225W合計電力消費 (PCIe 8ピンコネクタからの150W + PCIeマザーボードスロットからの 75W)を超える、単一PCIe 8ピンコネクタ装備のグラフィックスカード または拡張カード使用によって生じた損傷や故障の場合、 SilverStoneの製品保証は適用外となります。同様に、375W合計電力 消費(2基のPCIe 8ピンコネクタからの300W + PCIeマザーボードスロ ットからの75W)を超える、デュアルPCIe 8ピンコネクタ装備のグラフ ィックスカードまたは拡張カード使用によって生じた損傷や故障の場 合も、製品保証適用外となります。 TW 電源供應器接頭過度使用定義 單條PCIe 8pin電源線與接頭的最大額定電流為12.5A,瓦特數150W( + 12V x 12.
1. 為了保護使用者及防火的目的,安裝此交換式電源供應器時,必須安裝於符合下列各項要求的外殼中, 並且安裝妥善後,才可接上電源。 1-1. 外殼材質須為防火外殼。外壳材质须为防火外壳。 1-2. 外殼的上方及側邊之圓形開孔,最大內徑不可大於5mm。 1-3. 外殼的上方及側邊之長條型開孔,對角線距離不可大於5mm;若寬度小於1mm,則長度不受限制。 1-4. 外殼底部不可有開孔。外壳底部不可有开孔。 直徑不大於5mm Openings that do not exceed 5mm in any dimension 對角線不大於5mm 寬度小於1mm 則長度不限 Openings that do not exceed 1mm in width regardless of length 2. 本產品輸出含有危險能量,為避免操作時發生危險,須於裝入系統機殼並將所有設備安裝妥當後才可開啟電源。 3. 本產品之電源輸出非屬電力限制型電源,請連接使用具防火外殼之周邊,以避免火災危險發生。 BSMI ROHS 資訊 http://www.silverstonetek.com/downloads/PSU/RSD.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ※付属の電源コードは当該製品専用です。他の機器に使用しないでください。 Please refer to SilverStone website for latest specifications updates.