SX-500 and SX-510 Serial Device Server User’s Reference Guide
© 2008 Silex Technology America, Inc. All rights reserved. November, 2008 Silex Technology America SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OF THIS PRODUCT FOR A PARTICULAR PURPOSE. Silex shall not be liable for any errors contained in this manual or for any damages resulting from loss of use, data, profits, or any incidental or consequential damages arising from the use of SILEX products or services.
Contents About This Reference Guide ..................................................................................................................................... 1 Safety Precautions................................................................................................................................................. 1 Emissions Disclaimer.............................................................................................................................................
Appendix B Console Commands............................................................................................................................ 49 Wireless and Network Security Commands ........................................................................................................ 49 Port Commands ................................................................................................................................................... 56 Server Information Commands .................
Table 15 Table 16 Table 17 Table 18 Table 19 Table 20 Table 21 Contents Port Commands....................................................................................................................................... 56 Server Information Commands ............................................................................................................... 57 Service Commands ..............................................................................................................................
About This Reference Guide Safety Precautions To prevent damage to the Serial Device Server’s electronic circuit components, follow established ESD practices and procedures for handling static-sensitive devices. All ESD-sensitive components must be stored and shipped in ESD-conductive bags or bubble-wrap and labeled as such using the standardized ESD adhesive warning label.
Page 2 Silex Part Number 140-00188-180 About This Reference Guide
Chapter 1: Introduction The SX-500 and SX-510 Serial Device Servers provide a complete solution for connecting serial devices to 802.11 wireless or Ethernet wired networks. The following models are available: • SX-500-003x Ethernet model. The SX-500 Ethernet model includes an RS-232-C device interface, 10Base-T/100Base-T Ethernet network interface, and AC power supply. • SX-500-103x Wireless model. The SX-500 Wireless model includes an RS-232-C device interface, an 802.
Page 4 Silex Part Number 140-00188-180 Introduction
Chapter 2 Installing the Serial Device Server Hardware The Serial Device Server includes most of the hardware and software components required for installation. The one item that you will need to purchase separately is a cable to connect your serial device to the Serial Device Server (this cable is not included because of the wide variety of connector types used on serial devices). Verify Package Contents The Serial Device Server includes the components listed in Table 1.
2. Write down the 12-digit MAC (Media Access Code) address printed on the label located on the bottom of the Serial Device Server (for example: 004017023F96). You may need this number in order to configure the Serial Device Server. 3. If you have a wireless model, connect the antenna to the unit. 4. Connect the Serial Device Server to your serial device. If you are using RS-232, you may use standard PC cabling (you should normally use a null modem crossover cable).
• If the Serial Device Server is operating properly, the LEDs will blink momentarily and then go out, the yellow and green LEDs will illuminate if the wireless network is active, and the orange LED will illuminate, indicating the device is receiving power. • The unit powers up in the Normal mode, which provides for connection from the network to device(s) connected to the serial port of the Serial Device Server. • If the orange LED blinks continuously in a regular pattern, a problem exists.
Function State Yellow Off Green Blinking Yellow On Green On Yellow Blinking Green Blinking Page 8 Status 100base-TX network data received Wireless network active, if WLAN model Wireless network data received, if WLAN model Silex Part Number 140-00188-180 Installing the Serial Device Server
Chapter 3 Configuring the Serial Device Server This chapter describes the methods for configuring the basic settings of the Serial Device Server, including the IP address, serial port settings, and wireless security. The Serial Device Server also has an extensive range of advanced configuration capabilities that are described in Chapter 5, Appendix A, and Appendix B.
• • • Character Size Flow Control Line Mode (RS-232, RS-422, RS-485 full-duplex, RS-485 half-duplex; RS-422 and RS-485 are supported on the SX-510 only) In addition to the above parameters, the Serial Device Server allows you to configure numerous other capabilities. These other capabilities provide you with the unparalleled flexibility to use the Serial Device Server on virtually any 802.11 or Ethernet network with a wide range of serial devices.
Using the ExtendView Utility to Configure the Serial Device Server (Ethernet Connection) NOTE: Skip this section if you do not have a Windows PC or if you do not have an Ethernet connection available for configuring your Serial Device Server wireless model.
3. Right-click on the Serial Device Server that you want to configure from the displayed list, and then left-click on Configuration. The default Serial Device Server name is SLXxxxxxx (where xxxxxx is the last six digits of the MAC address from the label that is affixed to the Serial Device Server). 4. If you do not have a DHCP server, you will be asked to manually enter an IP address (if you are not sure what IP address to enter, ask your network administrator). Click OK when you are finished. 5.
6. Click the Wireless tab to configure the 802.11 wireless settings (for wireless models only; skip to the next section if you have a wired model). To operate on an 802.11 network, the Serial Device Server configuration must be configured with the wireless configuration and security parameters necessary for the Serial Device Server to communicate over your wireless network (check with your network administrator if you do not know these parameters).
8. You do not need to change any of the settings in this window. Click the Serial Settings button to configure the serial port. 9. Configure the serial port settings so that they match the settings on your device. For example, if your device is set for 9600bps, odd parity, and XON/XOFF flow control, you must change the settings on the Serial Device Server to these settings. If are using either RS-422 or RS-485 (SX-510 only), select 422 or 485 as the Mode.
First-Time IP Address Configuration NOTE: Skip this section if you have already configured the SX-500 IP address with ExtendView If you are configuring the Serial Device Server from a non-Windows computer or if you cannot use an Ethernet connection, you must first configure the Serial Device Server IP address.
affixed to the Serial Device Server). For example: arp –s 192.168.5.53 00:40:17:00:00:01 ping 192.168.5.53 Note that Windows systems use the format xx-xx-xx-xx-xx-xx for the MAC address (for example, 00-0017-00-00-01). You will see a reply from the Serial Device Server with the number of bytes and other information if the address was successfully set. If you get an error message or no response, then the IP address was not set.
Using a Web Browser to Configure the Serial Device Server After you have entered an IP address into the Serial Device Server, you can use any standard web browser to access the internal web pages for configuring the Serial Device Server. Simply specify the IP address of the Serial Device Server in your browser and then follow the steps below: You may skip this section if you have completely configured the SX-500 using ExtendView. However, if you have advanced configuration requirements, such as 802.
If you used DHCP, verify that the IP address is correctly set. If you used the default 192.0.0.192 IP address, you MUST change it to a new valid IP address. If necessary, change the Subnet Mask and Gateway. It is generally not necessary to change the other parameters on this page (refer to Chapter 5 for advanced configuration information. Note that on-line help information is available on every configuration page.
5. Select the appropriate wireless encryption mode and enter the required settings (check with your network administrator for the proper settings if you do not know them). Appendix A lists the possible encryption settings. Click the Submit button at the bottom of the window (you may need to scroll) to save your changes. Now click I/O Port on the left side of the screen to configure the serial port. 6. Configure the serial port settings so that they match the settings on your device.
telnet aa.bb.cc.dd where aa.bb.cc.dd is the IP address of the Serial Device Server (for example, telnet 192.168.5.6). 2. Press and then enter the password access at the # prompt. Press at the Enter Username> prompt. When you see the Local> prompt, you can enter console commands. 3. If you used the default 192.0.0.192 IP address to connect to the Serial Device Server, you MUST change it to a new valid IP address. If necessary, you must also change the Subnet Mask and Router (Gateway).
6.
Page 22 Silex Part Number 140-00188-180 Configuring the Serial Device Server
Chapter 4 Using the Serial Device Server with Your Application The Serial Device Server includes a number of capabilities that enable it to be used in a wide range of applications. These capabilities include: 1. 2. 3. 4. 5. 6. 7. 8. 9. Serial Port Emulator (SPE) software Raw TCP connection RFC2217 ECable Mode Print Server mode FTP Console mode switching AT commands SNMP traps and Email alerts These methods are described in the following sections.
After the Serial Port Emulator software has started, you will see a list of all the configured Serial Device Servers on the network. Right click on the name of the Serial Device Server that you want the virtual COM port to connect to (the default name is SLXxxxxxx, where xxxxxx is the last six digits of the Serial Device Server MAC address), and then click Virtual Port. You will be asked to select the name of the virtual COM port (for example, COM3).
where ipaddress is the IP address of the Serial Device Server and portnumber is the Serial Device Server TCP port number. For example: telnet 192.168.5.
a. Select UDP as ECable I/O Mode. b. Enter the UDP port number (Destination Port) used by the destination device to communicate with the Serial Device Server. This number must be a valid port on the destination device (check the documentation for that device to determine the valid port numbers). c. Enter the UDP port number (Local Port) used by the Serial Device Server to communicate with the destination device. This number must be greater than 1023, but is otherwise arbitrary.
To switch the serial port to console mode, you must first define a console string. When the Serial Device Server receives this string on the serial port, it will automatically switch the port to console mode. To define the console string, use a web browser to access the Serial Device Server internal web pages. After you log in, click I/O Port, and then select the desired port (S1 for the serial port).
Page 28 Silex Part Number 140-00188-180 Using the Serial Device Server
Chapter 5 Advanced Configuration The Serial Device Server Serial Device Server is equipped with a default configuration that works with most serial-to-Ethernet connections. You can modify the settings to suit your installation requirements. The web browser interface is the recommended method for setting advanced configuration parameters (some of the advanced configuration parameters are not accessible via ExtendView).
Parameter Description Settings Default Setting Ecaddr ECable destination IP address Set by user N/A Econn ECable connection attempt time 1-255 seconds 30 seconds Ecport ECable destination TCP port number Set by user N/A Eclport ECable destination local IP port number (required for E-Cable UDP mode only) Set by user N/A Ectmmsec Cable connection time resolution Enable, Disable Disable Ecudp ECable UDP mode Enable, Disable Disable Restoring Factory Default Settings The factory defa
2. Verify the settings, as defined in Table 4. Table 4 TCP/IP Settings Parameter IP Address Resolution Setting Sets the exchanges among network interfaces connected to an Ethernet media segment and maps IP address to Ethernet addresses, Media Access Control (MAC) addresses and hardware addresses. The Set Permanent radio button sets the IP address permanent. The IP address must follow the format XXX.XXX.XXX.XXX, where each XXX is a number between 0 and 255.
Figure 4 Advanced TCP/IP Configuration Window 5. Configure the settings, as defined in Table 5. Table 5 TCP/IP Configuration Settings Parameter Setting TCP Connection Timeout Sets the timeout and reset values for the TCP connections Unsolicited ARP Blocks or broadcasts unsolicited ARP DNS Sets the DNS addresses 6. To accept changes, click OK. To cancel, click Cancel. For additional help, click Help. NOTE: You can configure the same settings using the Web Page configuration.
Table 6 describes the messages used to communicate between the network manager and the SNMP agent, as defined in RFC 1157. Each SNMP message must contain a Community Name, which is used like a password. The default Community name for the Serial Device Server Serial Device Server is PUBLIC. Table 6 SNMP Commands Command GET Description Retrieves management information for a specific managed object contained in the agent. The GET message must contain the OID for the specified object.
Figure 5 SNMP Configuration 8. Click the Submit button to save the changes. You must then restart the Serial Device Server to make the changes take effect. Configuring Serial Port Monitor Alert and Trap Configuration The Serial Device Server can be configured to scan and compare the data received on the serial port to user-defined strings. A match with a string can be a source for SNMP traps and/or email alerts.
Command Description Example: Local> show port s1 trigmon Index # ------ Monitor String -------------- Local> set port s1 trigmon 0 trigger on seeing this string Local> show port s1 trigmon Index # -----0: Monitor String -------------trigger on seeing this string SHOW PORT S1 TRIGXMT Shows email or web page strings associated with TRIGMON index numbers SET PORT S1 TRIGXMT Assigns email or web page string to specified TRIGMON index number Index # = 0 to 7 Example: Local> show po
This screen allows you to define up to eight Email addresses that can receive alert information. Each address can receive any combination of the alerts that you have defined previously. You must enter the IP address of your SMTP server and the Email address(es) where you want the alerts to go. For example, in the above screen, the user has configured two serial port match strings. He has decided to send an alert to the mail address admin@companyxyz.com if the first match string is seen on the serial port.
Table 8 describes the AT Commands. Table 9 details the Extended AT Commands that allow the configuration of the network server operating parameters. Any AT command received, except the listed commands, are acknowledged with OK status. This allows existing modem applications to transmit commands without causing an error. These include ATn, but not currently AT&n, AT%n, AT\n, where is a letter.
Parameter Quiet mode Command ATQn Description If n = 1, no result codes are returned. If n = 0, result codes are returned to the local device. 0 is the reset default value. Verbose mode ATVn If n = 0 and not in quiet mode, result codes are returned in numerical form. If n = 1, results are returned as text. 1 is the reset default value. Table 9 Extended AT Commands Parameter Console pass through Command AT#C Description Passes the string to the server configuration console.
Response Codes Table 10 details the response codes for codes other than #C commands. Table 10 Response Codes Numeric Code Description 0 OK 2 No Carrier 4 Error 5 Connect 8 No Answer Using ExtendView for Bulk Configuration The ExtendView Utility has a powerful bulk configuration capability that allows you download configuration information to multiple Serial Device Servers simultaneously.
Page 40 Silex Part Number 140-00188-180 Advanced Configuration
Chapter 6 Troubleshooting If you have experience problems with the Serial Device Server, please check the following troubleshooting steps: 1. Make sure that you are getting power to the Serial Device Server. The orange LED should be on solid if the proper power is being received. If it is not on, check the power supply connections, and if possible, try a different Silex Serial Device Server power supply. 2. Make sure that you have a valid network connection. a.
b. If you are using RS-422 or RS-485, make sure that you have set the Serial Device Server’s serial port line mode as described in Chapter 3. c. Make sure that have a good cable connection between your serial device and the Serial Device Server. If possible, try a different cable. d. Make sure that the cable pinouts are correct.
Chapter 7 Product Specifications Table 11 Product Specifications Component Specifications Model SX-500 Serial Device Server, SX-510 Serial Device Server Processor Cavium NITROX Soho CN210 RAM Memory 16 Mbytes SDRAM. Processor Speed 167 MHz Interfaces Supported Serial: RS-232-C; SX-510 models also support RS-422 and RS-485 (full and half-duplex) Ethernet: 10/100BaseT Wireless: 802.11b/g (SX-500); 802.11a/b/g (SX-510) Dimensions SX-500: 125.73 x 75.11 x 24.08 mm (4.95 x 2.957 x 0.
Parameter Specifications 2.412 GHz ∼ 2.484 GHz ISM band Operating Frequency 5.15 GHz ∼ 5.25 GHz ISM band 5.725 GHz ∼ 5.825 GHz ISM band Data Modulation Type Orthogonal Frequency Division Multiplexing (OFDM) Complementary Code Keying (CCK) Differential Quadrature Phase Shift Keying (DQPSK) Differential Binary Phase Shift Keying (DBPSK) Channel Number IEEE 802.11b and g: Channels 1 to 11 and 12 to 14 IEEE 802.11a: Channels 36, 40, 44, 48, 149, 153, 157 and 161 (802.
Appendix A Advanced Security Configuration There are numerous possible security settings. It is therefore important that you verify the appropriate settings with your network administrator. If you enter the settings incorrectly, the Serial Device Server will not be able to communicate on your network.
The following is a description of the authentication settings used by the Serial Device Server: Encryption Mode (Wireless Security Only) The possible Serial Device Server wireless encryption modes include: • • • • • 64 and 128 bit WEP. These are available for basic WIFI compatibility. Because of known security issues, WEP should be avoided if possible. Dynamic WEP. Dynamic WEP uses WEP encryption with an 802.1X EAP authentication method.
Wireless Authentication Type (Wireless Security Only) This parameter sets the type of authentication to be performed with the network access point (Radius authentication server), or with a peer unit in Ad Hoc mode. The Serial Device Server supports Shared Key and Open System Authentication with WEP, and PSK, TLS, TTLS, LEAP, PEAP, and EAP-FAST with WPA, WPA2, DYNAMIC WEP, and WPA2-WPA. ).
• Certificate Root Key This is the authentication key used to verify the root certificate in the certificate chain provided by the authentication server. To set to null, send leave this field blank. Enter the certificate root key on the Configure Authentication Certificate page in the Serial Device Server internal web pages, or use the console command SET NW CERTKEY , where is the value of the key.
Appendix B Console Commands The following tables describe the console commands available from the internal command console. Access the command console through the serial port (if enabled for console mode) or over the network using a Telnet session or a web browser.
Command SET NW AUTHtype Description Sets wireless authentication type The default value is Open System Format: SET NW AUTHtype [OPEN | SHARED | TTLS | LEAP | PEAP | TLS | FAST | WPA-PSK ] SH NW AUTH Shows wireless authentication type Sample output: Authentication type= OPEN SYSTEM SET NW ETHAUTH Sets Ethernet wired authentication type The default value is Open System Format: SET NW ETHAUTH [TTLS | TLS | PEAP ] SH NW ETHAUTH Shows Ethernet wired authentication type Sample output: Authentication type=
Command SET NW KEY# Description Selects the WLAN WEP key entry (the WEP key that will be used as the transmit key) The possible values are 1, 2, 3, or 4; the default value is 1. Format: SET NW KEY# SET NW KEYVAL n Sets the WLAN WEP key entry to the specified hex value For WEP128, the key is 10 hex characters long; for WEP128, the key is 26 hex characters long; the default value is null.
Command Description CL NW BSsid Clears BSSID value and allows the server to use SSID, not a specific AP Format: CL NW BSsid SET NW RTS Sets WLAN RTS threshold The possible values are between 1 and 3000; the default value is 2432.
Command SH NW CERTCN Description Shows the value of first common name check string The default is null (blank) string. The command SH NW TTCN also returns this information. Sample output: Common name 1 SET NW CERTCN2 Sets second EAP Common Name Format: SET NW CERTCN2 SH NW CERTCN2 Shows the value of the second common name check string The default is null (blank) string. Sample output: Common name 2 SET NW CERTEXP Sets EAP Certificate Exponent value The default value is 10001 Hex.
Command SET NW INAP Description Sets EAP inner-authentication protocol The possible protocols are PAP and MSCHAP_V2; the default value is PAP. Format: SET NW INAP SH NW INAP [PAP|MSCHAP_V2] Shows the inner authentication mode The deprecated command SH NW TTAP also returns this data. Sample output: Authentication protocol = PAP SET NW REALM Sets the realm portion of the 802.1x EAP authentication ID This value can also be set with the ID command. The default value is null.
Command SET NW WPAPSK Description Sets WPA PSK pass phrase or hex key. This value is only used if the authentication mode is WPA-PSK or WPA2-PSK. The argument to this command is either a pass phrase of 8 to 63 characters or exactly 64 hex characters representing the 256 bit PSK value. Format: SET NW WPAPSK SH NW WPAGROUP Shows state of the allow WPA group keys flag Sample output: WPA-GROUP Disabled SET NW WPATRACE Sets WPA trace level. This command is for diagnostic purposes only.
Port Commands Table 15 Port Commands Command SH PORT Description Shows port parameters Sample output: Port Q-Size *S1 CLEAR PORT S1 JOB Type 0 serial Attributes 115200 N 8 1 XON/XOFF Aborts the active job on the port. If the remote host is connected, additional data received will be discarded. Format: CL PORT S1 JOB SET PORT S1 FLOW Sets serial port flow control to NONE, XON/XOFF, CTS, or DSR The default value is none.
Server Information Commands Table 16 Server Information Commands Command SET SERVEr Description SET SERVEr NAme Description Sample Output Sets server description string Format: SET SERVEr DEscription Sets server node name The default value is TWC_xxxxxx, where xxxxxx are the last 6 hex digits of the MAC address. Format: SET SERVEr SET SNMP GETCOMM NAme Gets community name The default value is public.
Command SH SERVEr Description Sample Output Shows server parameters Sample output: Serial Server Serial # 9047595 Address: 00-40-17-8A-0E-2B Number: 0 Identification: Name: TWC_8A0E2B Network Server Enabled Characteristics: Link DOWN SH SERVEr CO SH SNMP Shows server network statistics Sample output: Seconds Since Zeroed: 163 Frames Sent,1 Collision: 26 Bytes Received:72950 Frames Sent, 2+Collision: 5 Bytes Sent:18726 Send Failures: 0 Frames Received:752 Send Failure Reasons: 0 Frames Sent:
Service Commands Table 17 Service Commands Command SET SERVI BOT Description Sets beginning of transmission (BOT) string index for service The SH SERVI STRings command displays the available strings and their associated number; the default value is 1. Format: SET SERVI BOT SET SERVI EOT Sets end of transmission (EOT) string index for service The SH SERVI STRings command displays the available strings and their associated number; the default value is 1.
Command SET SERVI FMS Description Sets filter 1 text replacement match string index. If the index is zero, the default string of (line feed) is used. The default value is 0. Format: SET SERVI FRM SET SERVI FRS nn Sets filter 1 text replacement replace string index. If the index is zero, the default string of (carriage return-line feed) is used. The default value is 0.
Command Description SET SERVI TCP Sets raw TCP port for service If port number is 0, raw TCP is disabled on service. The default value is 9100 for service 1, 3001 for service 2. Format: SET SERVI TCP SH SERVI SUMmary [service_num] nn Shows the basic parameters for a specific service. If service_num is not provided, parameters for all services are displayed. The command SH SERVI displays the same data as SHOW SERVI SUM.
Command SH STRing [string_num] Description Defines the BOT and EOT strings used in services If string_num is provided, then the specific string definition and expansion are displayed. If string_num is not provided, then all string definitions are displayed without their expansions. Sample output: 1: 2: \1BE 3: \04 4: \1B%-12345X 5: @PJL 6: ENTER LANGUAGE= 7: PCL\0A 8: POSTSCRIPT\0A 9: \FF\04\FF\05\FF\06\FF\07 10: \FF\04\FF\05\FF\06\FF\08 11: \0C SH FILters Shows the filters that can modify a job stream S
Command SET IP RANge Description Allows or prevents access to a range of remote addresses The default value is empty list. Format: SET IP RANge [EN | DI | ALL] aa.bb.cc.dd {MAx ee.ff.gg.hh] SH IP ACcess Displays current access list settings Sample output: All hosts permitted access SET IP ADdress Sets server IP address The default value is 192.0.0.192 Format: SET IP ADdress aa.bb.cc.dd SET IP ARP ENable Enables or disables setting of IP address with an ARP packet The default value is Enable.
Command SET IP FTP Description Enables or disables FTP protocol The default value is Enable. Format: SET IP FTP SET IP HTTP [ENable | DIsable] Enables or disables HTTP protocol The default value is Enable. Format: SET IP HTTP SET IP KEepalive [ENable | DIsable] Sets interval in minutes for sending TCP keepalive packets on a connection The default value is 5 minutes. Format: SET IP KEepalive n SET IP LPD Enables or disables the LPD protocol The default value is Enable.
Command SET IP ROuter Description Sets default router address The default value is 0.0.0.0. Format: SET IP ROuter SET IP SUbnet aa.bb.cc.dd Sets IP subnet mask The default value is 0.0.0.0. Format: SET IP SUbnet SET IP TCP aa.bb.cc.dd Enables or disables the raw TCP 9100 protocol The default value is Enable. Format: SET IP TCP SET IP TELnet [ENable | DIsable] Enables or disables Telnet protocol The default value is Enable.
Command SH IP Description Shows TCP/IP related parameters Sample Output: IP is enabled IP address 192.0.0.192 Boot tries 3 Subnet mask 0.0.0.0 Boot method AUTO IP Gateway 0.0.0.0 Max window 10240 (set manually) LPD banner disabled LPD retries are disabled Service SET IP TRAP n TRIG Timeout 1 min Keepalive 5 min Port TCP port xxxxxx_S1_A S1 9100 xxxxxx_S1_B S1 3001 Specifies the trigger conditions that will cause a trap to be sent.
Firmware Update Table 20 Firmware Update Command SET LOAd ENable Description Sets the firmware to perform a soft reset and enter the server boot program after the next Exit command. This command is used for diagnostic purposes only. The default value is Disable. Format: SET LOAd (ENable | DIsable ] SET LOAd HOst Sets the node name of the Netware boot host. This command is used for diagnostic purposes only. The default value is null>\ Format: SET LOAd HOst SET LOAd IP Sets source computer IP add
Miscellaneous Commands Table 21 Miscellaneous Commands Command Description SET DEFAULT Set parameters to factory defaults EXIT This command exits the current configuration console session. SH FATal Shows fatal error log, if fatal errors exist. CL FATal Clears the fatal error log INIT Instructs the server to execute a soft reset when the next exit command is executed.
Appendix C Firmware Update Procedures Occasionally it may be necessary to update the Serial Device Server to take advantage of new features or to fix specific problems. The simplest way to perform this update is with the Silex UpdateIP utility for Windows XP and 2000 computers. This utility can be found on the CD-ROM that is included with the Serial Device Server, or it can be downloaded from the Support & Downloads section of the Silex website (www.silexamerica.com). To use UpdateIP: 1.
tftp -i 192.168.5.70 put /updates/tathsti130.bin access If you are using a different operating system, please refer to the documentation of that operating system for information on how to use the tftp command. Note that you should specify that the tftp destination file is the Serial Device Server password (“access” by default).
Appendix D Safety and Regulatory Notices Information for United States Users (SX-500 & SX-510) This equipment has been tested and found to comply within the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Declaration of Conformity (FCC) (SX-500) According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: Located at: Silex Technology America, Inc. 157 West 7065 South Salt Lake City, UT 84047, USA Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device FOR HOME OR OFFICE USE.
Information for European Users (SX-500) The server and its built-in 802.11b, and 802.11g wireless technology is in compliance with the Class B Information Technology Equipment requirements and other relevant provisions of European Directive 1999/5/EC. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communications devices. The internal function is a radio device using the 2.4 GHz frequency band (2.
Declaration of Conformity (FCC) (SX-510) According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: Located at: Silex Technology America, Inc. 157 West 7065 South Salt Lake City, UT 84047, USA Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device FOR HOME OR OFFICE USE.
Information for European Users (SX-510) The server and its built-in 802.11abg wireless technology is in compliance with the Class B Information Technology Equipment requirements and other relevant provisions of European Directive 1999/5/EC. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communications devices. The internal function is a radio device using the 2.4 GHz frequency band (2.400GHz - 2.
The SX-510 complies with standards for the following countries: USA: FCC Standard: Part 15, Subpart B, Subpart C and subpart E FCC ID: N6C-SX510 Medical EMC: IEC 60601-1-2:2001 Safety: UL 60950-1 (CSA Mark) SAR: ANSI/IEEE Std. C95.
Appendix E Silex Contact Information Silex Technology America, Inc. www.silexamerica.com Technical Support: support@silexamerica.com Sales: sales@silexamerica.com Tel: (801) 748-1199 8:00 to 5:00 Mountain Time Tel: (866) 765-8761 toll-free Fax: (801) 748-0730 Silex Technology Europe GmbH www.silexeurope.com Tel: +49-2159-67500 Tel: 0800-7453938 German toll free Email: contact@silexeurope.com Silex Technology Beijing, Inc. www.silex.com.cn Tel: +86-10-8497-1430 Email: contact@silex.com.
Part Number 140-00188-180
Silex Technology America, Inc. www.silexamerica.
