$00_WT-4_En.book Page 40 Friday, August 10, 2007 2:02 PM 6 Configuring the Network / Macintosh / Creating an Ad Hoc Network After choosing a network name and channel and adjusting encryption and password options as described below, click [OK]. • Name: Enter a name of up to 32 characters. • Channel: Choose a channel. • Enable encryption (using WEP): Select this option to enable WEP encryption. • Password: If WEP encryption is enabled, enter a security key.
$00_WT-4_En.book Page 41 Friday, August 10, 2007 2:02 PM ❏ Connecting to an Infrastructure Network Procedures for connecting your computer to a wireless LAN access point are described here. Following the instructions in the manual for the wireless LAN access point, choose a network name (SS-ID), authentication, encryption, security key, and key index. Configuring the Host 1 Open [System Preferences] and click [Network].
$00_WT-4_En.book Page 42 Friday, August 10, 2007 2:02 PM 2 Configuring the Network / Macintosh / Connecting to an Infrastructure 3 Choose [Network Port Configurations] from the [Show] menu. Enable [AirPort], drag it to the top of the list, and click [Apply Now].
$00_WT-4_En.book Page 43 Friday, August 10, 2007 2:02 PM 4 Choose [Preferred networks] from the [By default, join] menu and click [+]. Introduction Configuring the Network / Macintosh / Connecting to an Infrastructure 5 Choose [AirPort] from the [Show] menu.
$00_WT-4_En.book Page 44 Friday, August 10, 2007 2:02 PM 6 Configuring the Network / Macintosh / Connecting to an Infrastructure Enter the network name and other settings for the wireless access point and click [OK]. • Network Name: Enter a name of up to 32 characters. • Wireless Security: Choose from [None], [WEP Password], [WEP 40/128-bit hex], [WEP 40/128-bit ASCII], [WPA Personal], and [WPA2 Personal]. [LEAP], [WPA Enterprise], [WPA2 Enterprise], and [802.1X WEP] can not be used with the WT-4.
$00_WT-4_En.book Page 45 Friday, August 10, 2007 2:02 PM 7 Click [Apply Now]. Introduction Configuring the Network / Macintosh / Connecting to an Infrastructure Network setup is now complete. Proceed to “Operating the WT-4 for Computer” (pg.47), “Operating the WT-4 for FTP” (pg.107).
$00_WT-4_En.
$00_WT-4_En.book Page 47 Friday, August 10, 2007 2:02 PM Operating the WT-4 for Computer The WT-4 can be operated in one of the following four modes: Transfer mode: Upload images to a computer. Thumbnail select mode: Use the supplied software Thumbnail Selector to select and download images while viewing them as thumbnails (reduced images) on your computer.
$00_WT-4_En.book Page 48 Friday, August 10, 2007 2:02 PM Copying Network Profiles to the Camera / Ad Hoc Networks Copying Network Profiles to the Camera Ad Hoc Networks 1 Connect the UC-E4 as shown below. 2 Turn the camera on. Power switch MMY 3 Turn the computer on and start the WT-4 Setup Utility. • Windows: Double-click the [WT-4 Setup Utility] icon on the desktop • Macintosh: Click the [WT-4WirelessSetup] icon in the Dock.
$00_WT-4_En.book Page 49 Friday, August 10, 2007 2:02 PM The dialog shown below will be displayed; click [Next]. 5 Select [Add/Edit profiles] and click [Next].
$00_WT-4_En.book Page 50 Friday, August 10, 2007 2:02 PM A Copying Network Profiles to the Camera / Ad Hoc Networks The “Select Action” Dialog The other options in the “Select Action” dialog are described below. Note that the camera need not be connected to a computer to choose a printer or change the upload folder. • Change password: The dialog shown at right will be displayed. By default, no password is required to change device profiles using the WT-4 Setup Utility.
$00_WT-4_En.book Page 51 Friday, August 10, 2007 2:02 PM Select [Add new profile] and click [Next]. 7 Enter the following information and click [Next]: • Profile name: Enter a name of up to 16 characters. • Profile type: Choose [Computer]. • Interface type: Choose [Wireless & Ethernet] for networks that include wireless, or [Ethernet only] for Ethernet-only networks.
$00_WT-4_En.book Page 52 Friday, August 10, 2007 2:02 PM 8 Select [Manual setup] and click [Next].
$00_WT-4_En.book Page 53 Friday, August 10, 2007 2:02 PM A [Automatic setup] cannot be selected in the following cases: • When editing a preset network • When using a third party network adapter • When the computer network is set to a static IP address • When the OS is Windows XP SP1 or Mac OSX Operating the WT-4 for Computer Copying Network Profiles to the Camera / Ad Hoc Networks “Automatic Setup” Choose [Automatic setup (recommended)] when using a new network for the first time.
$00_WT-4_En.book Page 54 Friday, August 10, 2007 2:02 PM 9 Enter the following information and click [Next]. Copying Network Profiles to the Camera / Ad Hoc Networks • Network name (SSID): Enter a network name or choose from a list of existing networks. Do not change the name if it is supplied automatically. • Network type: Select [Ad hoc]. • Channel: Select a communication channel.
$00_WT-4_En.
$00_WT-4_En.book Page 56 Friday, August 10, 2007 2:02 PM 10 Select [Obtain IP address automatically] and click [Next]. Copying Network Profiles to the Camera / Ad Hoc Networks • Obtain IP address automatically: Select this option if the network is configured to supply IP addresses automatically. If the network does not include a DHCP server, addresses will be supplied by Auto IP (pg.180). • IP address: If the network is configured for manual IP addressing, enter an IP address for the WT-4.
$00_WT-4_En.book Page 57 Friday, August 10, 2007 2:02 PM 11 Confirm that settings are correct and click [Next]. Operating the WT-4 for Computer Copying Network Profiles to the Camera / Ad Hoc Networks 12 Select [Finish wizard] and click [Next].
$00_WT-4_En.book Page 58 Friday, August 10, 2007 2:02 PM 13 Turn the camera off and disconnect the USB cable. Copying Network Profiles to the Camera / Ad Hoc Networks UMMY The network profile has now been copied to the camera. Proceed to “Upload pictures to a host computer” (pg.70), “Thumbnail select mode” (pg.79), “PC Mode” (pg.90), “Print Mode” (pg.97).
$00_WT-4_En.book Page 59 Friday, August 10, 2007 2:02 PM Infrastructure Networks Connect the UC-E4 as shown below. 2 Turn the camera on. Power switch MMY 3 Turn the computer on and start the WT-4 Setup Utility. • Windows: Double-click the [WT-4 Setup Utility] icon on the desktop • Macintosh: Click the [WT-4WirelessSetup] icon in the Dock. 4 The dialog shown below will be displayed; click [Next].
$00_WT-4_En.book Page 60 Friday, August 10, 2007 2:02 PM 5 Select [Add/Edit profiles] and click [Next].
$00_WT-4_En.book Page 61 Friday, August 10, 2007 2:02 PM A Operating the WT-4 for Computer Copying Network Profiles to the Camera / Infrastructure Networks The “Select Action” Dialog The other options in the “Select Action” dialog are described below. Note that the camera need not be connected to a computer to choose a printer or change the upload folder. • Change password: The dialog shown at right will be displayed.
$00_WT-4_En.book Page 62 Friday, August 10, 2007 2:02 PM Copying Network Profiles to the Camera / Infrastructure Networks 6 Select [Add new profile] and click [Next]. 7 Enter the following information and click [Next]: • Profile name: Enter a name of up to 16 characters. • Profile type: Choose [Computer]. • Interface type: Choose [Wireless & Ethernet] for networks that include wireless, or [Ethernet only] for Ethernet-only networks.
$00_WT-4_En.book Page 63 Friday, August 10, 2007 2:02 PM 8 Select [Manual setup] and click [Next].
$00_WT-4_En.book Page 64 Friday, August 10, 2007 2:02 PM A Copying Network Profiles to the Camera / Infrastructure Networks “Automatic Setup” Choose [Automatic setup (recommended)] when using a new network for the first time. The following dialog will be displayed; if multiple infrastructure networks have been setup, select a setting which will be used for network connection and click [Next]. to proceed to Step 11 (pg.68).
