User Manual

ManualsBrandsSilex Technology ManualsElectronicsSX-10WAG

Connecting to the FTP Server

Operating the WT-4 for FTP140

Connecting to the FTP Server

Before connecting the WT-4, select [MTP/PTP] for the [USB] option

in the camera setup menu (pg.7) and confirm that the computer

intended for network connection is started and the user is logged

in.

1 Turn the camera off and insert the

memory card containing the pictures to

be sent.

• If there are multiple card slots, insert

the card into any slot.

To access the network via Ethernet, connect the Ethernet

cable (pg.2). Note that wireless transfer is disabled while an

Ethernet cable is connected. Disconnect the Ethernet cable

before accessing a wireless network. Turn the WT-4 off before

connecting or disconnecting the Ethernet cable.

2 Open the WT-4 USB connector cover and

connect the USB cable from the WT-4 to

the camera USB connector.

3 Turn the camera on.

DUMMY

Front

MMY

$00_WT-4_En.book Page 140 Friday, August 10, 2007 2:02 PM

Summary of content (12 pages)

PAGE 1
$00_WT-4_En.book Page 140 Friday, August 10, 2007 2:02 PM Connecting to the FTP Server Connecting to the FTP Server Before connecting the WT-4, select [MTP/PTP] for the [USB] option in the camera setup menu (pg.7) and confirm that the computer intended for network connection is started and the user is logged in. 1 Turn the camera off and insert the memory card containing the pictures to be sent. DUMMY • If there are multiple card slots, insert the card into any slot.
PAGE 2
$00_WT-4_En.book Page 141 Friday, August 10, 2007 2:02 PM 4 Connecting to the FTP Server 5 Select [Transfer mode] for the [Wireless transmitter] > [Mode] option in the camera setup menu (pg.152). A list of available connection profiles will be displayed. Highlight the desired profile and press J. A Viewing Profile Information Press the camera L (?) button to view information on the selected profile.
PAGE 3
$00_WT-4_En.book Page 142 Friday, August 10, 2007 2:02 PM 8 Connecting to the FTP Server A Confirm that the selected profile is displayed in green in the top level of the wireless transmitter menu. For information on what to do if an error is displayed, see “Troubleshooting” (pg.178). Using the Windows Vista Ad-hoc Connection To use the Windows Vista ad-hoc connection, turn on the WT-4 and conduct the following steps on your computer. 1 Click the [Start] and select [Connect To].
PAGE 4
$00_WT-4_En.book Page 143 Friday, August 10, 2007 2:02 PM Select a preset network name and click [Connet]. 3 Enter the network security key and click [Connect].
PAGE 5
$00_WT-4_En.book Page 144 Friday, August 10, 2007 2:02 PM 4 Click [Close].
PAGE 6
$00_WT-4_En.book Page 145 Friday, August 10, 2007 2:02 PM Uploading Images Press the K button to view pictures on the memory card. Display the first picture to be sent in single-image playback or highlight it in the thumbnail list. 2 While pressing the N button, press the center of the multi selector (D3) or the J button (D300). The image will be marked with a white “send” icon and transmission will begin immediately. During upload, images are marked with a green “sending” icon.
PAGE 7
$00_WT-4_En.book Page 146 Friday, August 10, 2007 2:02 PM 3 Turn off the WT-4 power. Uploading Images When the POWER LED (pg.3) changes from green to yellow and then goes out, detach the USB cable. • To change the destination folder, use the Setup Utility (pg.50, 126).
PAGE 8
$00_WT-4_En.book Page 147 Friday, August 10, 2007 2:02 PM ❏ Transfer Status During playback, the status of images selected for uploaded is shown as follows: Uploading Images a: “Send” Images that have been selected for upload are marked with a white a icon. b: “Sending” A green b icon is displayed during upload. c: “Sent” Images that have been uploaded successfully are marked with a blue c icon. A Loss of Signal Transmission may be interrupted if the signal is lost (pg.148).
PAGE 9
$00_WT-4_En.book Page 148 Friday, August 10, 2007 2:02 PM ❏ Network Status Uploading Images The status of the link between the host and the WT-4 is shown by the status LEDs and by the display in the top level of the wireless transmitter menu. The Status LEDs The POWER LED lights when the WT-4 is on. Signal quality is shown by the LINK LED: the faster the LED blinks, the better the signal and the faster data can be transmitted. The ERROR LED blinks to show that an error has occurred.
PAGE 10
$00_WT-4_En.book Page 149 Friday, August 10, 2007 2:02 PM The Status Display Network status can also be viewed in the top level of the wireless transmitter menu. Battery level: This icon shows five level of WT-4 battery level. Uploading Images e, f: The estimated time required to send the remaining images. Status area: The status of the connection to the host. The host name is displayed in green when a connection is established.
PAGE 11
$00_WT-4_En.
PAGE 12
$00_WT-4_En.book Page 151 Friday, August 10, 2007 2:02 PM Menu Guide This section describes the settings available for the [Wireless transmitter] option in the camera setup menu when the WT-4 is connected.