TM BluetoothTM Print Adapter User’s Guide Part Number 40150-100 Revision 0.2 TROY Group, Inc. Wireless and Connectivity Division • 1692 Browning • Irvine, CA 92606-4809 USA Tel: +1 (949) 399-0820 Fax: +1 (949) 399-0825 ª E-mail: support@troyxcd.com • www.troyxcd.
Copyright Notice All rights reserved. No part of this publication may be reproduced, stored, in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of TROY Group, Inc. The information contained herein is designed only for use with this TROY product. TROY is not responsible for any use of this information as applied to other products.
Contents Introduction Windows System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 About Your User’s Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 1 Installing the WindConnect Bluetooth Print Adapter Hardware Unpacking and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2 WindConnect Connector, Switch, and LEDs . .
iv
Introduction The TROY WindConnectTM BluetoothTM Print Adapter is a device that enables wireless communications capabilities on most models of printers. By using the WindConnect, you can conveniently print from laptop computers and other devices without using a cable, as shown in the diagram below. This manual covers installation of the WindConnect for use with laptop computers that have a TROY, IBM® or Toshiba Bluetooth PCMCIA card.
Note: The WindConnect Bluetooth Print Adapter is designed for printing text and low-resolution graphics. Because of the speed limitations of the Bluetooth wireless communications link, you should not use the WindConnect to print high resolution graphics or photographs. To get better printing performance with Bluetooth, you might want to consult your printer’s user guide.
1 Installing the WindConnect Print Adapter Hardware The WindConnect Bluetooth Print Adapter plugs directly into the parallel port of the printer. If desired you can simultaneously use the printer’s USB port for a hardwired connection to your PC.
Before Your Begin Before you install the WindConnect Bluetooth Print Adapter, make sure that your printer and your laptop computer already function properly via a parallel or USB printer cable. Refer to your printer’s documentation for instructions on using and maintaining your printer. In addition, make that you have properly installed the TROY, Toshiba or IBM Bluetooth adapter and software as described in the documentation that came with that device.
Connecting to the Printer Before connecting the WindConnect Bluetooth Print Adapter, make sure that the printer is turned off. The WindConnect has a 36-pin male Centronics parallel connector that is compatible with the 36-pin female connectors found on most printers. Therefore, the WindConnect can be plugged directly into the printer with no additional cable required. You are now ready to apply power to the WindConnect.
ing activity. Since you have not made a connection yet, both of these LEDs should be off. Verifying the Connection to the Printer Before attempting to print, it is very important to verify the connection between the WindConnect and the printer. If this connection is not good you will not be able to print! To verify this connection, make sure that both the WindConnect and the printer are powered on and ready. Then print a test page by holding in the test switch for less than five seconds.
2 Configuring the Software on Your PC You can now configure a laptop PC to print wirelessly to your EPSON printer equipped with an WindConnect Bluetooth Print Adapter. To do this, you will use the WindConnect Port Monitor software, which is included on the installation CD-ROM. The WindConnect Port Monitor greatly simplifies the Bluetooth printing process by combining the discovery and printing process into a single operation.
one of these older cards, first install the software and then upgrade the software using the Bluetooth Software Suite Upgrade included on the WindConnect installation CD-ROM. You must then verify that the Serial Port Profile is enabled on the Bluetooth Software Suite. To this: 1. Click the Windows Start button and select Control Panels. 2. The Control Panel window appears. Double click on the Bluetooth Configuration Tool. 3. You see the Bluetooth Configuration Tool dialog box.
rectly installed the Bluetooth PCMCIA card and software). Click on any one of these ports and verify that the Serial Port Profile is checked. If it is not checked, then click the box next to Serial Port Profile. 4. If you want to print to more than one Bluetooth device, you should repeat the above steps for one or more other Digianswer Virtual COM Ports.
2. In the Printers window, double-click Add Printer. 3. The Add Printer Wizard appears. Click the Next button. 4. Select Local Printer, and click Next.
5. Choose the manufacturer and the appropriate printer driver. Note that driver must support printing using a serial port. For example, not all Epson drivers will work, but the Epson Stylus Pro ESC/P2 driver is a generic serial port-compatible driver that allows most Epson printers to be used with the WindConnect. Click Next after you have finished selecting the manufacturer and printer model. 6. Choose the TBT1 virtual COM Port you created and click Next.
7. If desired, change the name of the printer to anything you like, such as “EPSON Stylus Color Printer Bluetooth”. Also, choose whether or not you want it to be the default Windows printer, and click Next. 8. Choose No to print a Test Page and click Finish. Since you have not made a Bluetooth connection yet, you will not be able to print a test page at this time. Printing the First Job You should now be able to print in the usual manner from any standard Windows application program.
gram. The first time you print, you will get a Port Monitor print screen similar to the one below: This screen will show all of the available WindConnect Bluetooth print adapters. If this is your first print adapter installation, you will only see one print adapter. Note that all WindConnect Bluetooth print adapters have the name XCD_xxxxxx, where “xxxxxx” is the last six digits of the MAC address (which is found on the label on the bottom of the unit).
Printing Additional Jobs After you print the first time, the port “remembers” that you have made a successful connection to your Bluetooth Print Adapter. If you print again within one minute, the job will be sent to the printer automatically and the Port Monitor screen will not appear. If you print again after a one minute delay, then you will again be presented with the Port Monitor screen.
3 Configuring Other Devices The WindConnect Bluetooth Print Adapter is designed to allow printing from a variety of different Bluetooth devices. Such devices must support the Bluetooth Serial Port Profile, the Object Push Profile, or the LAN Access Profile in order to work with the WindConnect Bluetooth Print Adapter. This is one of the most commonly available profiles, but check your device’s documentation to make sure that it is supported.
the previous chapter except that the local port is the COM port you created in step 1 instead of TBT1. 3. With some Bluetooth software you must first use the discovery program provided with the Bluetooth PCMCIA card, USB adapter, or built-in adapter to connect to the WindConnect Bluetooth Print Adapter (refer to the documentation provided with the Bluetooth device for additional information).
3. Click the Inquire button. You get a message “starting inquiry” and then a list of addresses of available WindConnect Bluetooth Print Adapter devices and other devices. The WindConnect Bluetooth Print Adapter address will appear in the format 004017xxxxxx; this is printed on the WindConnect Bluetooth Print Adapter box (all WindConnect devices begin with 004017). Click the address of the device you want to use.
5. If desired, change the Driver Name to match your printer (the standard Generic driver will work with most printers, but will not handle graphics). 6. Click Set As Default to save the settings and then click on the Home button to return to the main menu. You are now ready to print. To print: 1. Click the PrintBoy icon. 2. Click the category you wish to print (Appointments, To Do’s, Memos, etc.). Note: PrintBoy 2.
Using the WindConnect with Ericsson Mobile Phones The Ericsson R520 mobile phone supports printing address book cards (vCards) and other information using the Bluetooth OBEX Object Push Profile. To use the WindConnect Bluetooth Print Adapter with this phone, you must set enable a PIN number. To do this: 1.
3. Push the Yes key. 4. Push the 4 key to select Bluetooth. 5. Click the 3 key to discover the available Bluetooth devices on the network. You should get the message "Searching" 6. The WindConnect Bluetooth Print Adapter should appear in the list of available devices. Use the down arrow key to choose it and ten press the Yes key to select it. 7. Press the 1 key to select "Add to Paired". 8. Enter the passkey that you selected in the previous section and press Yes.
Using the Serial Port 4 The WindConnect has an RS-232 serial port that can be used to connect a console terminal, a serial printer, or a wide variety of other RS-232-compatible devices. The connector is an RJ45 modular jack similar to the type used on Ethernet networks (but not electrically compatible).
By default the serial port is set in console mode. In this mode, the port settings are permanently fixed at 115.2Kbps, 8-bit characters, no parity, and no flow control, and console operation. The console contains a variety of configuration and diagnostic commands. Most of these commands are beyond the scope of this manual, and they are documented on the TROY web site at www.troyxcd.com/tech. To use the serial port, connect the appropriate serial cable from a PC serial port (COM1 or COM2) to the WindConnect.
5 Troubleshooting If You Can’t Print If you are unable to print from your laptop or other device to the WindConnect Bluetooth Print Adapter, then check the following: 1. Make sure that the green light is on when you are printing. If it is not on, then there is no Bluetooth wireless connection. Unplug the WindConnect and then repeat the discovery process as outlined in the Discovering the WindConnect Bluetooth Print Adapter section in Chapter 2 of this manual.
5-2
Where to Get Help 6 TROY offers several customer support options to assist you in the event you experience difficulties with your WindConnect, including telephone support, repair services, extended warranty, and advance replacement. Worldwide Web Support The TROY worldwide web site provides a quick and easy way to answer many common technical questions. It includes a wide variety of technical support tips, as well as copies of product manuals, product literature, and firmware load images.
+49-(0)-800-3002210 (Europe and Africa) and request a Return Authorization Number from the TROY Technical Support Group. Make sure that you put this number on the outside of the shipping container you use to return the product and (if out-of-warranty) on your purchase order. You will also be asked for the serial number of the defective print server. Ship the unit freight prepaid back to TROY at the address provided by the Technical Support Group (adequate insurance is recommended).
Notices 7 FCC Compliance Statement For United States Users This equipment has been tested and found to comply within the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
For European Users This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. TROY Group cannot be responsible for any failure to satisfy the protection requirements resulting from a nonrecommended modification of the product.
REGULATORY INFORMATION European Union (EU) TROY hereby declares that the Bluetooth™ wireless technology built into the WindConnect Print Adapter, is in compliance with the essential requirements and other relevant provisions of European Directive 1999/5/EC. The internal Bluetooth™ function is a Bluetooth™ power class 1 intended radio device using the 2.4 GHz frequency band (2.400GHz – 2.4835GHz).
A minimum separation of 20 cm (8 inches) must be maintained between the antenna and the person for this device to satisfy the RF exposure requirements of the FCC. Note that any changes or modifications to this equipment not expressly approved by the manufacturer may void the FCC authorization to operate this equipment. Canada (IC notice) To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding.