DP 2-Port Gigabit Ethernet PCIe Installation Guide Introduction The DP 2-Port Gigabit Ethernet PCIe adds two 10/ 100/1000 Mbps Ethernet ports to your system. Features and Benefits • • • • • • 04-0820B Compliant with PCI Express Bus Specification, Revision 1.1 Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.
System Requirements • • Desktop computer with an available PCIe slot Windows® 10 (32-/64-bit) / 8.
Layout Active LED Link speed indicator LED RJ45 port Figure 1 Layout LED Indicators Two LEDs to monitor your network connection. • Active LED: Blinking green light when network activity is detected.
Hardware Installation Note: For low profile systems, replace the currently mounted bracket with the included low profile bracket. The design of computer cases and motherboards vary, refer to your computer's reference manual for further information if needed. Discharge any static electricity build up in your body by touching your computer case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. 1. Turn OFF the power to your computer. 2.
Windows Installation Install the board and boot up Windows, then follow the instructions below to install the DP 2-Port Gigabit Ethernet PCIe drivers. Windows 10 (32-/64-bit) / 8.x (32-/64-bit) / 7 (32-/64-bit) / Server 2012 R2 / Server 2008 R2 1. 2. Insert the driver CD. Close the CD autoplay window if prompted. Click Windows key and R. For Windows 10: Type D:\Windows\Win 10\setup.exe, click OK. (Change D: to match your CD\DVD-ROM drive letter) For Windows 8.x / Server 2012 R2: Type D:\Windows\Win 8_8.
3. 4. 5. 6. 7. At the User Account Control, click Yes. For Server 2008 R2 and 2012 R2, skip this step. At Welcome, click Next. At Ready to install the program, click Install. Skip this step if not prompted. Please wait while the driver install process continues. Click Finish to complete the installation. Windows Vista (32-/64-bit) / Server 2008 (32-/64-bit) 1. 2. 3. 6 Insert the driver CD. Close the CD autoplay window if prompted. Click Start, Run, type D:\Windows\Vista_ Server 2008\setup.
4. 5. 6. 7. At Welcome, click Next. Click Install. Skip this step if not prompted. Please wait while the driver install process continues. Click Finish to complete the installation. Windows XP (32-/64-bit) / Server 2003 (32-/ 64-bit) / 2000 1. 2. 3. 4. 5. 6. Click Cancel at the Found New Hardware. Skip this step if not prompted. Insert the driver CD, close the CD autoplay window if prompted. Click Start, Run, type D:\Windows\Win 2K_XP_2003\setup.exe, click OK. (Change D: to match your CD\DVD-ROM drive l
To Verify Windows Installation 1. 2. 8 Go to Device Manager to verify installation. For Windows 10 / 8 / 7 / XP / Server 2003 / Server 2008 R2 / 2000: Right click This PC, Computer or My computer, click Manage, then Device Manager. For Windows Vista: Right click Computer, click Manage, Continue, then Device Manager. For Windows Server 2012 R2: Right click This PC, click Manage, choose Tools, Computer Management, then click Device Manager.
Blank Page 9
Blank Page 10
Technical Support and Warranty QUESTIONS? SIIG’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analyst will promptly respond. SIIG offers a 5-year manufacturer warranty with this product.
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio.
