4K HDR HDMI 2.0 & USB 2.
Introduction The 4K HDR HDMI 2.0 & USB 2.0 Extender Over HDBaseT with RS-232 & IR extends HDMI transmission distance up to 330ft (100m) at 1080p or 230ft (70m) at 4K over an economical CAT5e/6 cable. Plus, bi-directional extension of IR, RS232 and USB 2.0 for advanced and interactive applications. Features and Benefits 2 Supports video resolutions up to 4Kx2K @60Hz (4:4:4 8bit) or HDR 4Kx2K @60Hz (4:2:0 10bit) to deliver crystal clear images 7.
Specifications Compliance HDMI 2.0a / HDCP 2.2 Resolution HDR 4Kx2K @60Hz (4:2:0 10bit) / 4Kx2K@60Hz (4:4:4 8bit) Audio LPCM, DTS-HD and Dolby True HD (7.1CH) Transmission Distance HDR 4Kx2K @60Hz: Up to 70m 1080p @60Hz: Up to 100m IR Signal Frequency 20KHz to 60KHz Connectors TX: 1x 19-pin HDMI Type-A, Female 1x 3.5mm audio jack (Stereo) 1x 3.5mm IR Blaster 1x 3.
Layout Note: With PoC technology, only one power adapter is needed to power both the Transmitter and Receiver. Stereo Input HDMI In IR Out IR In Figure 1: Transmitter (TX) - front HDMI In: Connect your HDMI source here with an HDMI cable (cable not included) Stereo Input: Provides a channel to extend an external analog audio to receiver over HDBaseT IR Out: Infrared 3.5mm socket. Plug IR Blaster extension cable here. See instructions on page 8. IR In: Infrared 3.5mm socket.
USB Type-A: Connect to USB Device Micro USB: Connect to USB Host Phoenix connector (RS232): Connect to the included terminal block and RS-232 connector (not included), then connect to a serial port device or computer for data transferring Dip Switch: Refer to below table for configuration - ON: In lower position - OFF: In upper position DIP Switch Position Description Connect Micro USB port to USB Host TX On (default) RX OFF (default) Connect USB device to Type-A port TX OFF Connect USB d
HDMI Out: Connect your HDMI display with an HDMI cable (cable not included) Stereo Output: External analog audio output from transmitter over HDBaseT S/PDIF Output: Local ARC output IR Out: Infrared 3.5mm socket. Plug IR Blaster extension cable here. See instructions on page 8. IR In: Infrared 3.5mm socket. Plug IR Receiver extension cable here. See instructions on page 8.
RS-232 Wire Connection 1. Insert the included terminal block to Phoenix connector. Figure 5 2. Connect the wires (not included) to the included Terminal Block and the RS232 connector as below diagram.
IR Extenders (20~60kHz IR devices supported) Figure 7: IR Blaster cable (Connect to IR Out) Figure 8: IR Receiver cable (Connect to IR In) IR Blaster cable: Plug into the Transmitter's or Receiver's IR Out to emit IR signals IR Receiver cable: Plug into the Receiver's or Transmitter's IR In to receive IR signals Control your media player (such as DVD) at the TV side using the media player's remote controller Plug the IR Receiver cable to the Receiver's IR In port Plug the IR Blaster cable to th
Hardware Installation Note: To achieve optimal performance, a shielded 100% copper wire CAT6/7 cable is recommended. 1. Power off all devices including your HDMI source and display. 2. Connect your HDMI source to the Transmitter's HDMI IN connector with an HDMI cable (not included). 3. Optional: Connect the IR Receiver or Blaster extension cable according to the instructions on page 8. 4. Connect USB Host/Device to both TX and RX units. 5. Connect audio source to TX and audio receiver/ speaker to RX unit.
Application Extends HDMI signals such as game consoles, DVD players or computers up to 100m (330ft). Equipped with bi-directional IR pass-through path, RS-232 serial port control and USB 2.0, offers the convenient path for interactive applications, such as touch panels. Makes it a great solution for digital signage with long distance A/V transmission.
Technical Support and Warranty QUESTIONS? SIIG’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analyst will promptly respond. SIIG offers a 3-year manufacturer warranty with this product.
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio.