Installation guide

ManualsBrandsSIIG ManualsAV extendersCE-H22611-S1

Introduction

The HDMI to CAT5e Daisy Chain HD Extender Kit with

RS-232 & IR extends HDMI signal over one Cat5/6 cable

up to 330ft and is cascade connection supported.

Features and Benefits

• Extend HDMI signals up to 100m over Cat5e/6

cabling

• Cascade receivers up to 10 layers

• Supports video high resolution Full HD 1080p, 1920

x 1080

• High Definition Audio (HD) Surround Sound

• RS-232 (Serial) and IR (Infrared Remote) enabled

• Metal housing with mounting mechanism

Package Contents

CE-H22611-S1

04-0957A

HDMI to CAT5e Daisy Chain

HD Extender Kit with

RS-232 & IR

Installation Guide

Summary of content (12 pages)

PAGE 1
HDMI to CAT5e Daisy Chain HD Extender Kit with RS-232 & IR Installation Guide Introduction The HDMI to CAT5e Daisy Chain HD Extender Kit with RS-232 & IR extends HDMI signal over one Cat5/6 cable up to 330ft and is cascade connection supported.
PAGE 2
CE-H22711-S1 Layout Transmitter Unit (Tx) Figure 1: Transmitter side panel • • • 2 DC 5V: DC 5V power jack. Plug the included power adapter here PWR: LED indicator for power status. On/Off when the Transmitter is powered on/off LINK: LED indicator for link status.
PAGE 3
• • • • • • RS-232: RS-232 control port. Plug the included 3.5mm to RS-232 cable then an RS-232 cable here, if needed HDMI IN: HDMI signal input port. Connect this port to your HDMI source device by using an HDMI cable (not included) HDMI OUT: HDMI signal output port.
PAGE 4
• • • • • PWR: LED indicator for power status. On/Off when the Receiver/Repeater is powered on/off LINK: LED indicator for link status. On when the connection of Transmitter and Receiver is established and detected RS-232: RS-232 control port. Plug the included 3.5mm to RS-232 cable then an RS-232 cable here, if needed HDMI OUT: HDMI signal output port.
PAGE 5
2. Point your source device's remote control to the IR receiver's eye, the command will be sent to Transmitter end, and the connected source device will enforce the command accordingly. Hardware Installation 1. 2. 3. Power off all devices, including the source device and display. Connect your HDMI source (such as a PC or NB) to the Transmitter's HDMI IN connector by using an HDMI cable. Connect the local HDMI display to Transmitter's HDMI OUT. source device local display Figure 4 4.
PAGE 6
. 7. Connect the two 3.5mm to RS-232 cables to the Transmitter and Receiver's RS-232 ports respectively. Skip this step if RS-232 control is not needed. Connect your CAT5/6 cable between the Transmitter's and Receiver's LINE port. Make sure the CAT5/6 LAN cable is securely connected. remote output display CAT5/ 6 cable source device local output display Figure 6 8. 9. 6 Each Receiver/Repeater can cascade-daisy chain to 2 or more Receivers/Repeaters for extending or expanding.
PAGE 7
Function Diagram Basic Connection remote HDMI IR receiver cable (optional) display IR blaster cable (optional) 2 HDMI source 1 2 local HDMI display 1 CAT. X cable 2 HDMI cable 2 Figure 7 • The extension distance through CAT.
PAGE 8
Advanced Connections Daisy Chain Connection HDMI Display 2 HDMI Rx Display 2 1 Rx HDMI Display 2 Rx 1 1 HDMI source 2 HDMI Display 2 1 CAT. X cable 2 HDMI cable Figure 8 • 8 The extension distance through CAT.
PAGE 9
Cascade Connection HDMI 1 CAT. X cable 2 HDMI cable Display 2 1 Rx HDMI Display 2 1 Rx HDMI HDMI source Display 1 Tx 2 2 HDMI Rx Display 2 Figure 9 • Cascade receivers up to 10 layers; extension distance through CAT.
PAGE 10
Gigabit Ethernet Switch Connection 2 1 Gigabit switch 1 1 CAT. X cable 2 HDMI cable Rx 1 1 Rx 1 Rx 2 Rx HDMI Display 1 Rx 1 Rx 1 2 Rx HDMI source HDMI Display HDMI Display Tx 1 Rx 1 Rx 2 2 HDMI Display Figure 10: Used with Gigabit Ethernet switch • • 10 Connect with the Gigabit Ethernet switch especially when your Tx or Rx unit has only one signal input/ output port The extension distance through CAT.
PAGE 11
Technical Support and Warranty QUESTIONS? SIIG’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analyst will promptly respond. SIIG offers a 2-year manufacturer warranty with this product.
PAGE 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio.